Behringer U-CONTROL UMX49 Range definitions, Factory Reset command, Optional controller functions

U-CONTROL UMX49/UMX61

b) Sequential scrolling in program libraries.

Most sound producers have the option to store presets in a separate bank (frequently called a User Bank). If the sequence of songs to be played at a concert is defined by your band, you can store all of the sounds used for the gig in the User Bank in the sequence they occur in the concert and completely concentrate on your playing. A cumbersome search for sounds in the sound producers is no longer required thanks to the OCTAVE SHIFT push-buttons.

1)Press the ASSIGN push-button and hold it down.

2)Press the key.

3)Release the ASSIGN push-button.

4)Finally, press the key. In order to discard your

assignments, please press the key or press the ASSIGN push-button again. The ASSIGN LED will go off in all 3 cases.

Pressing the right hand one of the two push-buttons now causes your external device to switch one preset number upward to be switched upward in your external device; pressing the left hand causes a step downward in your preset library. By pressing both push-buttons you jump to Preset 0 in the current bank.

Please note that you must assign an individual MIDI channel to the OCTAVE SHIFT push-buttons if you do not want to work in the GLOBAL CHANNEL (refer to chapter 4.2.2).

c) Optional controller functions

Please note that the OCTAVE SHIFT push-buttons generate switch controllers in the event of a controller assignment. One of the two values 0 or 127 will always be produced.

There are two exceptions: if you assign controller

CC07 (Channel Volume) to the OCTAVE SHIFT push- buttons, pressing one of the push-buttons will always generate the value 0. In case of controller CC 10 (panning), pressing a push-button will always produce the value 64.

Please note that pressing both push-buttons simultaneously does not generate anything when assigning a controller.

1)Press the ASSIGN button and keep it pressed.

2)Press the one of the two OCTAVE SHIFT buttons to which you want to assign a controller.

3)Release the ASSIGN button.

4)Press the number keys on the keyboard to enter the controller number of your choice (as described in chapter 4.2.1).

5)Confirm your selection with . To discard your

assignments either press the button or the ASSIGN button again. In either case the ASSIGN LED goes out.

Remember to assign the OCTAVE SHIFT buttons to an individual MIDI channel if you do not want to use the GLOBAL CHANNEL (see chapter 4.2.2).

4.2.10 RANGE definitions

The RANGE parameter can be defined for the PITCH BEND wheel and the key velocity.

a)for the PITCH BEND RANGE: This defines to what extent the movement of the PITCH BEND wheel affects the pitch of the sound. Proceed as follows to change the PITCH BEND RANGE:

1)Press the ASSIGN button and keep it pressed.

2)Use the number keys to enter the keyboard velocity (see table 4.1).

3)Release the ASSIGN button.

4)Confirm your selection with . To discard your

assignments either press the button or the ASSIGN button again.

KEY	EFFECT ON KEY VEOLCITY
	OFF: velocity value is fixed to 110.
	Change of key pressure has no effect on
	volume level.
	SOFT: key pressure is very sensitive; low
	velocity changes create high changes in
	volume level
	MEDIUM: key pressure is “normal”; (very) hard
	hit notes are (very) loud, (very) soft hit notes
	produce (very) low volume
	HARD: key pressure is more unsusceptible
	compared to all other settings
bis	invalid input

Table 4.1: Effect of RANGE definition on keyboard velocity

4.2.11 The FACTORY RESET command

To reset all settings on your UMX25, proceed as follows:

1)Press the ASSIGN push-button and hold it down.

2a) To cause a temporary FACTORY RESET, simultaneously press both OCTAVE SHIFT push-buttons. All temporarily changed control elements are returned to their factory settings. The USER MEMORY, however, is retained and will not be reset.

2b) Simultaneously press the , and

keys to perform a complete FACTORY RESET. In this case, the USER memory is also overwritten, in addition to resetting all control elements of the FACTORY MEMORY.

3)Release the ASSIGN push-button again. The LED of the ASSIGN push-button continues to be illuminated.

4)Finally, press the key. If you do not wish to perform

the RESET command, please press either the - key or press the ASSIGN push-button again.

12 4. OPERATION