PRO MIXER VMX300

15It the PFL MODE switch is set to SPLIT, the channels are strictly separated: channel 1 will be heard on the left side, channel 2 on the right. In this mode, the MIX control has no influence on the PFL signal.

2.4

3D surround function

The built-in QRS effect widens the stereo image and adds life and transparency to your sound—an easy way to put a unique final polish on your music and turn your performance into an incomparable experience. The SURROUND control determines the intensity of the effect, which can be turned on and off via the ON button.

2.5 Beat counter

The PRO MIXER VMX300’s built-in beat counter is an extremely useful feature, allowing smooth crossfades between two tracks—an important key to the success of your performance. The beat counter analyzes and displays the tempi of your tracks in BPM (Beats Per Minute). The beat counter sections of channel 1 and 2 are identical.

The tempo of the track is shown in the respective channel’s DISPLAY ( ). In the case of multiple tempo changes, the display would change continuously, causing unnecessary confusion and rendering the function virtually useless. Enter the SYNC LOCK button ( ): with it, you can limit the range of possible tempo values within a song. Pressing this button once the counter has “caught” and displayed a realistic value will simplify things. The BEAT ASSIST button ( ) allows you to set the beat counter’s tempo manually, similar to “tap tempo”. Pressing the button three times in time with the track will set the beat counter and its display at that tempo. The BEAT ASSISST and SYNC LOCK buttons are each equipped with an LED to show that the respective function is activated.

Once the tempo of the two tracks have been determined and locked with the SYNC LOCK or BEAT ASSIST buttons, the tempo difference between channel 1 and 2 will be depicted via the 9-segment TEMPO DIFFERENCE LED display ( ). It shows the degree of the tempo difference by a respective deflection to the right (channel 2 track is faster) or to the left (channel 2 track is faster). The center LED lights when the tempi are equal. The synchronization of channel 1 and 2 is shown in the TIME OFFSET LED display ( ) below the TEMPO DIFFERENCE display. When the center LED is lit, the tracks are in sync with each other. When the display moves to the left or right, the corresponding channel is running out of sync. The TEMPO DIFFERENCE and TIME OFFSET displays are only active when the tempi of both channels have been locked as explained above.

To exit the SYNC LOCK or BEAT ASSIST mode, simply press the SYNC LOCK key in both channels again.

2.6 Crossfader section

22

23

24

25

26

The CROSSFADER is used to fade between channels 1 and 2. Like the channel faders, the crossfader section is equipped with a 45-mm VCA-controlled fader.

The REVERSE switch (TAP/HOLD) enables you to invert the direction of the crossfader, so that you can quickly switch from channel 1 to channel 2. This effect is created by simply pushing the REVERSE switch down (TAP)—as soon as it is released, it returns to its original position and your crossfade setting (and your music) is at it was before. Pressed upwards, the switch locks into the reversed position (HOLD). To reset it, simply push it downwards.

The CROSSFADER CURVE control in the crossfader section is similar to the CURVE switches in the input channels (see ). The control allows you to fade between the various crossfader curve modes.

The KILL switches (TAP/HOLD) enable you to attenuate the three frequency bands (LOW, MID and HIGH) by -32 dB with a single press. Like the REVERSE switch, the switches lock in the upward position (KILL HOLD), and must be held in the downward position (KILL TAP). With other DJ mixers, the kill switches override the channel EQ’s. The VMX3000 is unique in that the kill switches supplement the channel EQ’s, allowing extreme attenuation of the respective frequency band. The left-side KILL switches are assigned to channel 2, the right-side switches to channel 3. There are no KILL switches for channel 1.

The MIC INPUT connector is a balanced ¼" TRS socket for microphone connection.

8

2. FRONT PANEL