position, the valve closes after 100 seconds.
• Fixing to the wall
Drill the holes A referring to the distances indicated (Fig.2). Fix the appliance to the wall and align it in horizontal posi- tion to the wall units. When the appliance has been adjusted, definitely fix the hood using the screws A (Fig.4). For the various installations use screws and screw anchors suited to the type of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with the product, check that they are suitable for the type of wall on which the hood is to be fixed.
• Fixing the decorative telescopic flue
Arrange the electrical power supply within the dimensions of the decorative flue. If your appliance is to be installed in the ducting version or in the version with external motor, prepare the air exhaust opening. Adjust the width of the support bracket of the upper flue (Fig.3). Then fix it to the ceiling using the screws A (Fig.3) in such a way that it is in line with your hood and respecting the distance from the ceiling indicated in Fig.2. Connect the flange C to the air exhaust hole using a connection pipe (Fig.4). Insert the up- per flue into the lower flue and rest above the frame. Extract the upper flue up to the bracket and fix it with the screws B (Fig.3). To transform the hood from a ducting version into a filtering version, fit the charcoal filters provided referring to the fitting instructions.
• Filtering version
Install the hood and the two flues as described in the paragraph for installation of the hood in ducting version. To assemble the filtering flue refer to the instructions contained in the kit. If the kit is not provided, order it from your dealer as accessory. The filters must be applied to the suction unit positioned inside the hood. They must be centred by turning them 90 degrees until the stop catch is tripped (fig. 7).
USE AND MAINTENANCE
•We recommend that the cooker hood is switched on before any food is cooked. We also recommend that the appliance is left running for 15 minutes after the food is cooked, in order to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
•The anti-grease filter is used to trap any grease particles suspended in the air, therefore is subject to saturation (the time it takes for the filter to become saturated depends on the way in which the appliance is used).
- To prevent potential fire hazards, the anti-grease filters should be washed a minimum of every 2 months (it is possible to use the dishwasher for this task).
- After a few washes, the colour of the filters may change. This does not mean they have to be replaced.
If the replacement and washing instructions are not
followed, the anti-grease filters may present a fire hazard.
•The active carbon filters are used to purify the air which
is released back into the room. The filters are not washable or re-usable and must be replaced at least once every four months. The active carbon filter saturation level depends on the frequency with which the appliance is used, the type
of cooking performed and the regularity with which the anti-grease filters are cleaned.
•Clean the cooker hood frequently, both inside and outside, using a cloth which has been dampened with denatured alcohol or neutral, non-abrasive liquid detergents.
•The light on the cooker hood is designed for use during cooking and not for general room illumination. Extended use of the light reduces the average duration of the bulb.
•Replacing halogen light bulbs (Fig. 8).
To replace the halogen light bulbs B, remove the glass pane C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type. Caution: do not touch the light bulb with bare hands.
•Replace incandescent/halogen/fluorescent lamps (Fig.9):
Only use lamps of the same type and Wattage installed on the device.
•Commands: (fig.5) mechanical the key symbols are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
• FILTER REMOVAL
WARNING - ENSURE THE APPLIANCE IS SWITCHED OFF AT THE MAINS BEFORE REPLACING THE BULBS AND FILTERS.
1.remove the filters by lifting the recessed handle and lift free from the hood frame.
2.To reinstall the filters position in the recess at the rear and press to lock in position.
BULB REPALCEMENT
1.Remove the filters
2.Unscrew the bulb in an anti-clock wise direction.
3.After installing the correct replacement bulb, refit the filter.
Replacement bulbs can be easily obtained from a good electrical or DIY store.
BEFORE CALLING SERVICE/TROUBLE SHOOTING
The hood was switched on but the unit does not operate.
•Have you plugged in/switched on the power supply at the socket?
•Check for a blown fuse/or trip.
Extraction is poor
•Check and clean the filters if required, if required, if active filters are present replacement filters maybe required.
•Check that the exhaust ducting is not obstructed.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE WARNINGS.
