Belkin F6C800-UNV F6C100, F6C120-UNV Technical Specifications, Storage, Safety Information

RS-232

Connector

USB

Connector

Using the serial or USB cable (provided), connect the cable to your UPS then connect the other end to the USB port on your computer.

Caution: Use only the factory-supplied UPS monitoring cable.

USB : HID Windows Setup Procedure

1.When the USB cable is first connected to a USB port on your computer, the Windows® 98 dialog called ADD NEW HARDWARE WIZARD should automatically appear. (To display this dialog manually, click the START button and choose SETTING to access the control panel, and double-click on ADD NEW HARDWARE.)

2.The ADD NEW HARDWARE WIZARD will guide you through the installation process. Click Next.

3.A dialog states, “Windows will now search for any new Plug- and-Play devices on your system.“ Click Next.

4.A subsequent dialog gives you these options: “Search for the best driver for your device (recommended) and display a list of all drivers in specific location. This enables you to select the driver you want. “Please accept the recommended choice by clicking NEXT.

5.The Wizard will then search your hard drive for a file called

“\INF\ hidden.inf”. This file contains all the information that Windows® OS needs to install the correct device drivers.

6.The wizard might ask for the Windows OS CD-ROM. Place the CD into the CD-ROM drive & select OK.

7.The installation process will continue to run until a dialog display shows that the drivers have been installed. Select the FINISH button and your drivers are installed.

G) Install the Software (Optional)

a)To fully utilize the UPS and its software, your computer must be able to operate the following operating systems: 95OSR2 / 98 / ME / NT4 /2000/XP & Novell 3.X & Higher and have a USB port.

b)Your UPS features the Bulldog Plus Shutdown Software. This allows you to protect and save your data should a power outage occur, as well as safely shutdown your computer in your absence. Please be sure to close out of all applications prior to installing the software.

1.To install the software, please place the CD into the CD drive of your computer.

2.Your computer should autorun the CD. If this does not occur, go to the Run feature on your Start icon (lower left corner) on your screen. Please enter the CD drive, it may be D: Upon entering the drive Run setup.exe. to execute the software. Should you continue to have a problem, please refer to your computer’s owner’s manual for the correct drive.

3.The “Welcome to the Belkin Bulldog Plus Product Installation Browser” will appear. Please click Install.

4.Upon clicking Install, the Bulldog Plus Installation window will appear. Please choose the appropriate software to install

5.InstallShield Wizard will appear onscreen, click Next.

6.Please read the License Agreement and click Yes.

7On Setup Type, ALL (Standalone) is the default. Standalone is for UPS management for your computer only. Networking management is for administrators who need to manage several UPSes in a workstation environment. You should not install the networking files unless you are technically qualified to use these features. For more information on networking, please refer to the software user’s manual.

8.On Choose Destination Folder, you have the option to choose the location of where you would like the Software located on your computer. We recommend using the default option as shown on screen. To use the default option, click Next.

9.On Select Program Folder, you have the option to choose the program folder for your Software. We recommend using the default option as shown on screen. To use the default option, click Next.

10.On the Select Language screen, please select your language choice.

11.The software will now be installed. Once completed, please click Finish.

Note!

Please refer to the help feature found on the Belkin On-line Screen. To access this screen, please click the Belkin shield found in the lower right corner on your task bar of your screen.

Once the Belkin On-line screen appears, choose help. The Bulldog Online Help screen will appear. You may use the Contents, Index or Search tabs to assist you with your help issues and to get more information on the specific features and functions of the software.

H) User Manual Installation

You will need Adobe Acrobat Reader to review the User’s Manuals. If you do not have the reader, please goto www.adobe.com to download a free version of the software.

1.From the “Welcome to the Belkin Bulldog Plus Product Installation Browser” window, locate and choose User Manual’s.

2.The “ Bulldog Plus User Manuals” window will appear. Please move your pointer to the manual you wish to open and click.

3.An Adobe pdf file will be opened. To save a copy to your hard drive, you will need to goto “File” on your menu bar and choose “Save a copy”.

4.On the Save a Copy window, please choose a destination folder for the manual.

I) Uni nstal l for Wind ows 9 5/98/ Me/NT 4/200 0/XP

The re ar e two options t o uninstall the Belkin Shutdo wn So ftwar e.

Opt ion 1

1.Click th e Sta rt icon in the lower left hand corn er of your scre en an d got o the Prog rams folde r. Scroll to th e Belkin Bulldo g Plu s folder and ch oose set up. Insta ll Wizard will appea r.

2.Cho ose Remove and click Next .

3.The Prog ram Files and Audio Files will be checke d. If they are not, ple ase check them. Click Next. Th e uninstall pro cedur e will beg in.

4.Click Finish when complete.

Opt ion 2

(No te: Windows XP users, cho ose the Co ntrol pane l fun ction from your Sta rt icon an d the n got o to step 2.)

1.Click th e Sta rt icon in the lower left hand corn er of your scre en an d got o the Sett ings icon. Goto and choose the Cont rol Panel folde r. Th e Con trol Pan el window will appea r.

2.Locate a nd click t he Add /Remo ve Pro grams icon . The Add /Remo ve Pro grams wind ow will ap pear.

3. Locate and ch oose the Belkin Bulldog Plus softwa re. Click the Cha nge/Remove butt on on the right . Install Wizar d will app ear.

4.Cho ose Remove and click Next .

5.The Prog ram Files & Aud io Files will be che cked. If they are no t, please che ck th em. Click Next. The uninstall proce dure will begin .

6.Click Finish when complete.

Please visit belkin.com for the latest software upgrades and information on your belkin ups.

TECHNICAL SPECIFICATIONS

MODEL		F6C800-UNV	F6C100- UNV	F6C120-
				UNV
	Capacity	800VA /450W	1000VA /	1200VA
			550W	/670W
INPUT	Voltage		90-136Vac
	Range
	Frequency		60HZ ( ±3HZ )
OUTPUT	Voltage	Simulated sine wave, 120vac±10%
	Frequency		60HZ ( ±1HZ )
	( on battery)
	Back up time
	Full / half	3-8 min	3-8 min	3-7 min
BATTERY	load
	Typical
	Recharge	_ 12hours recover 85% capacity
	Time
ENVIRONMENT	Ambient	0~85% humidity non-condensing, 0~35_
	operation
	Safety	UL / C-UL, meet FCC class B
CONFORMANCE
	Surge	Meet IEEE C62.41 Category A standard,
			890Joules.
	Dimension	120mm X 300mm X 190mm		(4.72” X 11.81”
PHYSICAL	(W X D X H)		X7.48”)
	Net weight	11.4KGS/25.13	13KGS/28.6	13.5KGS/29.7
		LBS	5LBS	5LBS

All specifications are subject to change without prior notice.

STORAGE

Storage Conditions

Store the UPS covered and upright in a cool, dry location with its battery fully charged. Before storing, charge the UPS for at least four hours. Disconnect any cables connected to the computer interface port to avoid unnecessary drainage of the battery.

Extended Storage

During extended storage in environments where the ambient temperature is +5 oF to +86 oF, charge the UPS battery every six months. During extended storage in environments where the ambient temperature is +86 oF to +113 oF, charge the UPS battery every three months.

Note:

Belkin Components User License Agreement

Away from sunlight Away from heat Away from water

Belkin Components (Belkin”) thanks you for choosing one of our products. This User License Agreement (Agreement”) contains the terms and conditions under which limited use of the product is licensed to you.

PLEASE READ THIS NOTICE CAREFULLY. DO NOT USE THE SOFTWARE OR PRODUCT UNTIL YOU HAVE READ AND AGREED TO THIS AGREEMENT. IF YOU USE THE SOFTWARE AND PRODUCT, YOU ARE AGREEING TO THE TERMS AND CONDITIONS SET OUT IN THIS AGREEMENT. IF YOU DO NOT ACCEPT THESE TERMS AND CONDITIONS, YOU MUST RETURN THE UNOPENED PRODUCT WITH THE DISKS INSIDE TO THE PARTY FROM WHOM YOU RECEIVED IT. SCOPE OF USE: In this Agreement, software means all machine- readable software programs and associated files in this package. All modified versions of and upgrades or improvements to such programs and all copies of such programs and files. You, a single user opening this envelope (You or our), may use the software on a single central processing unit. You may not rent it, loan it out, or lease it, nor use it on a multi-user system.

LICENSE: You have the non-exclusive right to use the software. You are not permitted to copy, modify or transfer the software or documentation. You may not compile, disassemble or otherwise reverse engineer, breakdown, analyze or modify the software.

USE AND RESTRICTIONS: You are permitted to make backup copies of all the software disks for archival purposes only. You must reproduce the proprietary notice set forth on the disks and affix them to all backup copies. You are not permitted to use these programs in connection with

a computer service, or to use the backup copies other than as a replacement for the original copy.

TERM: This license is effective upon acceptance by opening this envelope or in any other way using the enclosed software, which will constitute your acceptance of, and agreement to, this Agreement, and is effective until terminated. The limited license in this Agreement will be automatically terminated if you fail to comply with any of the Terms and conditions in this Agreement. You agree that upon such termination

you will immediately destroy all programs and documentation, including all copies made or obtained by you.

SOFTWARE, PROGRAM, DOCUMENTATION, AND ANY RELATED INFORMATION, GOODS OR SERVICES ARE PROVIDED WITH NO WARRANTY OR REPRESENTATION OF ANY KIND WHAT SO EVER. BELKIN HEREBY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

The entire risk of the use, results and performance of the software, program and documentation is borne by you. Should any or all of the product, software, program, documentation, or related information, goods or services be defective, misused, unsuitable or cause or give rise to any harm or liability whatsoever, you, not Belkin or its associates, dealers or agents, assume the entire liability, cost of repair, correction

or any payment or other remedy whatsoever. Furthermore, no warranty or guarantee is made regarding the use or results of the product, software, program, documentation, or any related information, goods or services in terms of correctness, accuracy, reliability, timeliness or otherwise. You use and rely on the program at your own risk. The following is the only and exclusive warranty and remedy of any kind: Belkin does warrant that the program disks are free from physical

defects in materials and workmanship under normal use for a period of one (1) year from the date of purchase, as evidenced by a copy of the sales receipt. Return the defective disk or documentation with your receipt directly to Belkin for a replacement.

DISCLAIMER: Belkin or its associates will in no event be liable (i) in any amount for lost profits or special, incidental, punitive or consequential damages, or (ii) for any claim or damage of any nature, or under any theory, whatsoever, in any amount in excess of the purchase price you paid for the product. The warranties and remedies here set forth are exclusive, and in lieu of all others oral or written, express or implied. Some jurisdictions do not allow exclusion or limitation of implied warranties or of liability for incidental damages, so the foregoing limitations or exclusion may not apply to you. This warranty gives you specific legal rights, which vary from jurisdiction to jurisdiction.

HOWEVER, YOU WAIVE SUCH RIGHTS, EXCEPT AS EXPRESSLY PROVIDED UNDER THE TERMS AND CONDITIONS OF THIS AGREEMENT, TO THE MAXIMUM EXTENT ALLOWED BY LAW. The license is governed by the laws prevailing in the State of New York, without regard to its conflicts of laws principles.

ACKNOWLEDGMENT:

By opening the package on which this Agreement is printed, or through which it is visible, you acknowledge that you have read this Agreement, understand it, and agree that this agreement is the complete and exclusive statement of agreement between yourself and Belkin and supersedes any prior agreements, oral or written, and any other communications relating to the subject matter of this Agreement.

SEVERABILITY:

Any term or provision of this Agreement or any application thereof, which may be prohibited or unenforceable by law in a particular jurisdiction, shall be interpreted and enforced to the maximum extent allowed in such jurisdiction (which the parties acknowledge could mean severing the provision from this Agreement or, if allowed, enforcing it in a narrower form), without affecting the remainder of this Agreement, or any other application of such term or provision in such jurisdiction, or application of such term or provision in any

Safety Information

CAUTION!

•Internal battery voltage is 12V DC.

•The unit is intended for installation in a controlled environment (temperature controlled, indoor area free of conductive contaminants).

•All batteries used are Sealed Lead Batteries. Batteries must be recycled.

Recycling Information

Your UPS contains a Non-spillable Sealed Lead Battery. On the battery, you will find the battery name. Please reference the chart below for recycling information.

Battery Name	Recycling Inside	Recycling Outside
	the USA	the USA
BB Battery	(800) 278-8599	N/A
CSB Battery	(800) 738-7372	1 (817) 244-4415
VISION Battery	(973) 726-5323	N/A