13CONTROLS
ENGINE SPEED CONTROL
HONDA ENGINE CONTROLS
Engine speed is set by using the throttle control lever, located in the middle of the operators handle.
B & S ENGINE CONTROLS
Increase Speed
START | STOP |
Throttle lever on handle
Decrease Speed
Decrease Speed
STOP | START |
Throttle lever on handle
Increase Speed
FUEL VALVE | CHOKE LEVER |
Set lever to choke position when starting a cold engine
RUN 
CHOKE
14INSTRUCTION LABELS
These labels should be included on your Aerator. If any of these labels are damaged, replace them before putting this equipment into operation. Item and part numbers are given to help in ordering replacement labels.
WARNING |
| |
EXPLOSIVE FUEL | 400268 | |
STOP ENGINE AND ALLOW TO | ||
|
15ENGINE LABELS
Briggs & Stratton
THIS ENGINE EQUIPPED WITH
LOW OIL SENSOR, IF ENGINE WILL
NOT START, CHECK OIL LEVEL
COOL BEFORE REFUELING. |
|
Label Hot Engine | Label Danger |
Part No.400268 | Keep Hands |
| and Feet Away |
| Part No.400424 |
RUN 
CHOKE
' ..
ON
' '
Read and follow Operating Instructions before running engine.
Gasoline is flammable. Allow engine
LIFT HERE
WARNING
THE UNIT WEIGHS OVER 300 LBS.
OFF
to cool at least 2 minutes before fueling.
Engines emit carbon monoxide, DO NOT run in enclosed area.
Label LIFT HERE
Part No.360187
WARNING
900327
Label Danger Guard
Part No.900327
LIFT HERE WITH CAUTION
Label Warning Unit Weight Part No.360188
START | STOP |
Label Throttle Control
Part No.810656
Honda
OPERATING INSTRUCTIONS |
|
|
|
|
| BEFORE STARTING, MAKE SURE: |
|
| |
TO START, MOVE ENGINE STOP SWITCH TO "ON" AND PULL ROPE. |
|
|
|
| TINE DEPTH CONTROL BAIL IS IN UP POSITION. |
|
| ||
NOTE: IT MAY BE NECESSARY TO USE THE ENGINE CHOKE IF |
|
|
|
| ALL GUARDS ARE ATTACHED. |
|
| ||
ENGINE IS COLD. |
|
|
|
| FOR PREVENTATIVE MAINTENANCE |
|
| ||
PUSH FORWARD ON TINE LIFT HANDLE TO ENGAGE TINES |
|
|
|
|
|
| |||
IN GROUND. |
|
|
|
|
| CHECK ENGINE OIL DAILY. |
|
| |
PUSH FORWARD ON OPERATOR’S BAIL TO ENGAGE DRIVE AND |
|
|
|
| INSPECT AND CLEAN ENGINE AIR FILTER DAILY. |
|
| ||
START AERATING. |
| READ OWNERS MANUAL | REPLACE AS NEEDED. |
|
| ||||
DURING OPERATION PUSHING DOWN ON OPERATOR’S HANDLE |
| GREASE ALL BEARINGS AND CHECK GEAR REDUCTION |
| ||||||
WILL MAXIMIZE CORING DEPTH. |
| BEFORE OPERATING |
| ||||||
| OIL LEVEL ON EVERY ENGINE OIL CHANGE. |
|
| ||||||
RELEASE BAIL TO STOP UNIT. |
|
|
|
|
|
|
| ||
NOTE: ENGINE WILL CONTINUE TO RUN WITH BAIL DISENGAGED. |
|
|
|
|
| ALWAYS: |
|
| |
TO TURN UNIT, PULL BACK ON TINE LIFT HANDLE TO LIFT TINES |
|
|
|
| INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY |
|
| ||
OUT OF GROUND. GRADUAL TURNS CAN BE MADE WITHOUT |
|
|
|
|
|
| |||
LIFTING THE TINES. |
| USE PERSONAL | WORN AND DAMAGED PARTS. | 360191 |
| ||||
| PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING. |
| |||||||
WITH TINES UP, PUSH FORWARD ON OPERATOR’S BAIL TO |
| PROTECTION EQUIPMENT | DISCONNECT SPARK PLUG WIRE BEFORE SERVICING UNIT. |
| |||||
ENGAGE WHEELDRIVE FOR ASSISTED TURNING. |
|
| |||||||
TO STOP ENGINE MOVE ENGINE STOP SWITCH TO "OFF". |
|
|
|
| USE ONLY A QUALIFIED MECHANIC T O SERVICE THIS MACHINE. |
|
| ||
Label Instructions AE - Part No. 360191
OIL ALERT
WHEN OIL LEVEL LOW, ENGINE STOPS IMMEDIATELY.
Part No. 360178 | Page 4 of 12 | Form No. F121203A |
