Billy Goat KD505SPQ Troubleshooting, Engine Service and Warranty, Serial Plate, Parts List, page

19			Item		Description				KD505SPQ
			No.						Part No.	Qty.
Parts List			86	WHEEL WITH SPROCKET ASS’Y CAST (21, 94, 95, 96)					900512	2
			87	CHAIN 52 PITCH					890239	2
continued from											* Denotes
			88	CHAIN 40 PITCH					900323	1
page 11.			89	WASHER FLAT 5/16 (3/8 ID x 7/8 x 1/16)					*8171003	4	standard
			90	BOLT CARRIAGE 5/16 -18 x 3/4					*8024039	4	hardware item
			91	WASHER SPRING LOCK 5/16					*8177011	4	that may be
			92	NUT REGULAR 5/16-18					*8142002	4	purchased
			93	JACKSHAFT					900320	1	locally.
			94	SPROCKET	(PER ASSEMBLY)	26 TEETH (Size 65A26)			890238	1
			95	SCREW SELF TAP 1/4-14 x 3/4		(PER ASSEMBLY)			800505	5
			96	WASHER LOCK EXTERNAL TOOTH (PER ASSEMBLY)					*8181007	5
			97	JACKSHAFT ASS’Y (INCLUDE. 93, 101, 102, 107, 108, 109)					890197	1
			98
			99	LABEL CLUTCH					830503	1
			100	LABEL-DANGER GUARDS					900327	1
			101	BEARING PLATE					900317	2
			102 BEARING BALL (WITH SNAP RING)						900321	2
			103	WASHER LOCK 1/4					*8177010	4
			104	ROD BAIL CLUTCH					900970	1
			105	BAR BRACE HANDLE					900768	1
			106 SCREW CAP 5/16-18 x 3/4						*8041026	1
			107	SPROCKET - 17 TOOTH					900303	1
			108	SPROCKET - 8 TOOTH					900302	2
			109	ROLL PIN 3/16 DIA. x 1 1/4 LG.					*8195166	4
			110	LOCKNUT 5/16 - 18 FLANGE					850164	5
			112	BRACKET CONTROL ASS’Y (INCL. 113, 114, 115)					900221	1
			113	SPRING					900136	1
			114 ROLL PIN 1/8” DIA. x 1 1/4 LG.						*9195106	1
			115	ROD CLUTCH					900208	1
			116	SCREW CAP 1/4-20 x 1/2” LG.					*8041002	3
			117 WASHER 1/4” FLAT (5/16 ID x 3/4 OD x 1/16)						*8171002	8
			118	GUARD CHAIN ASS’Y					890231	1
			119	CLIP-CLUTCH CABLE					900999	1
			120
			121	CLUTCH DOUBLE RELEASE					900307	1
			122	WASHER FENDER 5/16					*8172020	1
			123 LABEL READ OWNER'S MANUAL						890301	1
20	TROUBLESHOOTING					Before Requesting Service Review These Suggestions
	Problem				Possible Cause						Solution
Will not vacuum or has poor				Dirty debris bag. Nozzle height set too high or too low. Hose kit cap					Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
vacuum performance.				missing. Clogged nozzle or exhaust. Excessive quantity of debris.					Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
									Allow air to feed with debris.
Abnormal vibration.				Loose or out of balance impeller or loose engine.					Check impeller and replace if required. Check Engine.
Engine will not start.				Throttle in off position. Out of gasoline. Bad or old gasoline.					Check stop switches, throttle, and gasoline. Connect spark plug wire.
				Spark Plug wire disconnected. Dirty air cleaner.					Clean or replace air cleaner. Or contact a qualified service person.
No self propelling.				Operator's bail not releasing clutch. Broken or out of adjustment					Adjust clutch cable. Adjust bracket control assembly. Replace any
				clutch cable. Worn or broken clutch assembly. Bracket control					worn or damaged or malfunctioning parts.
				assembly (item 112) out of adjustment.
Self propelled drive will not				Clutch cable out of adjustment. Clutch not lubricated and is locked-up. Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
release .
Engine is locked, will not				Debris locked inside impeller. Engine problem.					See page 5, Contact an engine servicing dealer for engine problems.
pull over.
22.1		Engine Service and Warranty					22			WARRANTY PROCEDURE
								Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
	Contact your nearest engine manufacturer's autho-
				rized servicing dealer.				The WARRANTY terms are stated on the lower part which remains with the
								user. Whenever a Billy Goat Machine is faulty due to a defect in material
21	Serial Plate			Record your machine model, serial number				and / or workmanship, the owner should make a warranty claim as follows:
				and date-of-purchase and where purchased				The Machine should be taken to the dealer from whom it was
					1803 S. Jefferson			purchased or to an authorized Billy Goat dealer.
	L A				P.O. Box 308			The owner should present the remaining half of the Warranty
					Lee's Summit,
	95			R	MO 64063 / USA			Registration Card, or, if this is not available, the invoice or receipt.
					Tel (816) 524-9666
					Fax (816) 524-6983			The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
		Model			Serial No.			who will send it with the faulty part to Billy Goat headquarters.

									The Quality / Service department at Billy Goat headquarters will study
L									the claim and parts and will notify their conclusions.
	A								The decision by the Quality / Service department at Billy Goat
		Unit(Weight)			Engine Power
p
108									headquarters to approve or reject a Warranty claim is final and
			lbs.	kg		kW	rpm		binding.
Operator							min-1	Note: To process a Warranty Claim, it is necessary to quote the Model
									& Serial number who are printed on the Billy Goat Serial Plate.

Purchase Purchased

Datefrom

BILLY GOAT INDUSTRIES INC.

P.O. BOX 308 (1803 S JEFFERSON LEE'S SUMMIT, MO 64063 / USA PHONE: 816-524-9666 FAX: 816-524-6983

Part No. 890311 Page 12 of 12 Form No. F010396C