Billy Goat PR550, PR550H, PR550V, PR550HV, OS551, OS551H specifications Slicing Blade Wear

17MAINTENANCE

Use only a qualified mechanic for any adjustments, disassembly or any kind of repair .

WARNING: TO AVOID PERSONAL INJURY, ALWAYS

TURN MACHINE OFF, MAKE SURE ALL MOVING

PARTS COME TO A COMPLETE STOP.

DISCONNECT SPARK PLUG WIRE

BEFORE SERVICING UNIT.

ENGINE: See engine manufacturer operator's instructions.

RECONNECT SPARK PLUG WIRE,

AND ALL GUARDS, BEFORE

STARTING ENGINE.

USE ONLY BILLY GOAT ORIGINAL

EQUIPMENT PARTS FOR

REPLACEMENT AND REPAIR

BLADE WEAR AND ROTATING REEL END TO END

FLAIL BLADE WEAR

1.Wait for engine to cool and disconnect spark plug.

2. Close fuel valve on engine (if available).

3.Lean unit back onto lower handles and secure in place.

4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the overall length of the blade. (See fig. 1)

5.If blades measure less than 3.25"(83 mm) in overall length they must be replaced. NOTE: We recommend replacing all the flails at once.

Fig. 1

SLICING BLADE WEAR

1.Wait for engine to cool and disconnect spark plug.

2.Close fuel valve on engine (if available).

3.Lean unit back onto lower handles and secure in place.

4.Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the overall length of the blade from the center of the attachment bolt to the tip of the worn blade.

5.If blades measure less than 3"(76 mm) in length they must be replaced. NOTE: We recommend replacing all the blades at once.

ROTATING FLAIL REEL END TO END

To maximize flail blade life and performance the reel can be rotated end to end periodically to provide a fresh lead cutting edge. Takes approx. 20 min. and requires 1/2" and 9/16" socket wrenches with extension bar.

1.Wait for engine to cool and disconnect spark plug.

2. Close fuel valve on engine (if available).

3.Lean unit back onto lower handles and secure in place.

4. Remove (6) lock nuts(item 62) holding the belt and shaft guards(item 21 &22) in place. It is necessary to lower the height adjust lever to reach the locknuts on the guards. Remove the guards.

5.Remove the drive belt(item 9) by "walking" it out of the groove on the reel pulley(item 2).

6.Remove the (4) lock nuts(item 60) and washers(item 68) holding the bearings(item 23) to the frame of the unit.

7.The reel is now free from the machine. Slide the reel down and out of the machine.

8.Remove the capscrew(item 71), lockwasher(item 57), reel pulley(item 2), key(item 42), and reel spacer(item 10) from the end of the reel.

9.Rotate the reel end to end, and re-install these items on the opposite end of the reel.

10.Re-install the reel in reverse order of removal. Re-install the guards in reverse order of removal.

DRIVE BELT REPLACEMENT

NOTE: Takes approx. 10 min. and requires 1/2" socket wrench with extension.

1.Wait for engine to cool and disconnect spark plug.

2 . Remove (3) lock nuts(item 62) holding the belt guard(item 21) in place. It is necessary to lower the height adjust lever to reach the locknuts on the guard. Remove the guard.

3.Remove the belt(item 9) by rotating the reel pulley(item 2) and walking it out of the groove. Discard old belt

4. Install new belt using same procedure to walk the belt into the groove.

5.With new belt installed pull bail rod back to engaged position and measure extension of idler spring. Spring should stretch 3/4" - 1" (19

25mm) with bail engaged. Adjust clutch cable as necessary to achieve this extension.

6.Re-install the belt guard.

Maintenance Schedule	Follow these hourly
	maintenance intervals.
Maintenance Operation	Every Use	Every
	(Daily)	25 hrs

Engine (See Engine Manual)

Check engine oil

Inspect and clean engine air filter

Grease reel bearings

Inspect belt

Inspect for loose, worn, or damaged parts

Oil height adjustment linkage

Part No. 350324 Page 10 of 16 Form No. F031605A