Billy Goat TKD505SPT Troubleshooting, Parts List, continued from, page, Model, Serial No, min-1

19		Item	Description	TKD505SPT	Qty.
		No.		Part No.
		86	WHEEL WITH SPROCKET ASS’Y CAST (21, 94, 95, 96)	890242	2
Parts List		87	CHAIN 52 PITCH	890239	2
continued from		88	CHAIN 40 PITCH	900323	1
page 11.		89	WASHER FLAT 5/16 (3/8 ID x 7/8 x 1/16)	*8171003	4
		90	BOLT CARRIAGE 5/16 -18 x 3/4	*8024039	4
		91	WASHER SPRING LOCK 5/16	*8177011	4	* Denotes
	92		NUT REGULAR 5/16-18	*8142002	5	standard
		93	JACKSHAFT	900320	1	hardware item
		94	SPROCKET (PER ASSEMBLY) (SIZE # 65A26) 26 TEETH	890238	1
						that may be
		95	SCREW SELF TAP 1/4-14 x 3/4 (PER ASSEMBLY)	800505	5	purchased
		96	WASHER LOCK EXTERNAL TOOTH (PER ASSEMBLY)	*8181007	5
						locally.
		97	JACKSHAFT ASS’Y (INCLUDE. 93, 101, 102, 107, 108, 109)	890197	1
		98	SHIELD MUFFLER TKDSP	890190	1
		99	LABEL CLUTCH	830503	1
	100		LABEL-WARNING GUARDS	900327	1
		101	BEARING PLATE	900317	2
		102	BEARING BALL (WITH SNAP RING)	900321	2
		103	WASHER LOCK 1/4	*8177010	2
		104	ROD BAIL CLUTCH	900970	1
		105	BAR BRACE HANDLE	900768	1
		106	SCREW CAP 5/16-18 x 3/4	*8041026	1
		107	SPROCKET - 17 TOOTH	900303	1
		108	SPROCKET - 8 TOOTH	900302	2
		109	ROLL PIN 3/16 DIA. x 1 1/4 LG.	*8195166	4
		110	LOCKNUT 5/16 - 18 FLANGE	850164	5
		111
		112	BRACKET CONTROL ASS’Y (INCL. 113, 114, 115)	900221	1
		113	SPRING	900136	1
		114	ROLL PIN 1/8” DIA. x 1 1/4 LG.	*9195106	1
		115	ROD CLUTCH	900208	1
		116	SCREW CAP 1/4-20 x 1” LG.	*8041006	2
		117	WASHER 1/4” FLAT (5/16 ID x 3/4 OD x 1/16)	*8171002	6
		118	GUARD CHAIN ASS’Y TKDSP	890195	1
		119	CLIP-CLUTCH CABLE	900999	1
		120	PLATE BRACE HT. ADJ. KD / TKD	900756	1
		121	CLUTCH DOUBLE RELEASE	900307	1
		122	WASHER FENDER 5/16	*8172020	1
	123		LABEL READ OWNER'S MANUAL	890301	1

20		TROUBLESHOOTING		Before Requesting Service Review These Suggestions
	Problem			Possible Cause	Solution
	Will not vacuum or has poor		Dirty debris bag. Nozzle height set too high or too low. Hose kit cap		Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
	vacuum performance.		missing. Clogged nozzle or exhaust. Excessive quantity of debris.		Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
					Allow air to feed with debris.
	Poor chipping performance.		Extremely hard wood. Dull or damaged chipper blade.		Avoid extremely hard wood. Sharpen or replace chipper blade (see
					page 8).
	Engine stalls or labors when		Feeding branches into chipper too rapidly. Engine service may be		Feed branches at a slower rate. Service engine.
	chipping.		required.
	Abnormal vibration.		Loose or out of balance impeller or loose engine.		Check impeller and replace if required. Check Engine.
	Engine will not start.		Throttle in off position. Out of gasoline. Bad or old gasoline.		Check stop switches, throttle, and gasoline. Connect spark plug wire.
			Spark Plug wire disconnected. Dirty air cleaner.		Clean or replace air cleaner. Or contact a qualified service person.
	No self propelling.		Operator's bail not releasing clutch. Broken or out of adjustment		Adjust clutch cable. Adjust bracket control assembly. Replace any
			clutch cable. Worn or broken clutch assembly. Bracket control		worn or damaged or malfunctioning parts.
			assembly (item 112) out of adjustment.
	Self propelled drive will not		Clutch cable out of adjustment. Clutch not lubricated and is locked-		Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
	release.		up.
	Engine is locked, will not		Debris locked in chipper blade, hopper or inside impeller. Engine		See page 5, Clearing a clogged chipper hopper. Contact an engine
	pull over.		problem.		servicing dealer for engine problems.

22.1	Engine Service and Warranty
	Contact your nearest engine manufacturer's autho-
		rized servicing dealer.
21	Serial Plate	Record your machine model, serial number
		and date-of-purchase and where purchased

WARRANTY PROCEDURE

22Please fill in the WARRANTY CARD and send the upper part to Billy Goat. The WARRANTY terms are stated on the lower part which remains with the user. Whenever a Billy Goat Machine is faulty due to a defect in material and / or workmanship, the owner should make a warranty claim as follows:

The Machine should be taken to the dealer from whom it was purchased or to an authorized Billy Goat dealer.

L A

97

LpA

109

Operator

R

1803 S. Jefferson		P.O. Box 308
Lee's Summit,	MO	64063	/ USA
(816) 524-9666	FAX (816) 524-6983
Model			Serial No.
Unit (weight)			Engine Power
lbs		kg	kW	min-1
			@

The owner should present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.

The Warranty Claim will be filled in by the authorized Billy Goat Dealer, who will send it with the faulty part to Billy Goat headquarters.

The Quality / Service department at Billy Goat headquarters will study the claim and parts and will notify their conclusions.

The decision by the Quality / Service department at Billy Goat headquarters to approve or reject a Warranty claim is final and binding.

Note: To process a Warranty Claim, it is necessary to quote the Model & Serial number who are printed on the Billy Goat Serial Plate.

Purchase	Purchased
Date	from
Part No. 890316

BILLY GOAT INDUSTRIES INC.

P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA

PHONE: 816-524-9666 FAX: 816-524-6983

Page 12 of 12 Form No. F082195D