Bionaire 127176 warranty Heater Safety, Important Instructions, Consumer Safety Information

HEATER SAFETY

PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1.	Read all instructions before using the appliance.
2.	To avoid fire or shock hazard, plug the appliance directly into
	a 120V AC electrical outlet.
3.	The heater is hot when in use. To avoid burns, DO NOT
	let bare skin touch hot surfaces. Use handle when moving
	this heater. Keep combustible materials, such as furniture,
	pillows, bedding, papers, clothes, and curtains at least 3
	ft (0.9 m) from the front of the heater and keep them away
	from the sides and rear.
4.	DO NOT run cord under carpeting. DO NOT cover cord with
	throw rugs, runners, or the like. Arrange cord away from
	traffic area and where it will not be tripped over.
5.	This heater is not intended for use in bathrooms, laundry
	areas and similar indoor locations. NEVER locate heater
	where it may fall into a bathtub or other water container.
6.	Extreme caution is necessary when any heater is used by,
	or near children or invalids, and whenever the heater is left
	operating and unattended.
7.	Always unplug the heater when not in use.
8.	When unplugging, be sure to pull by the plug and not the
	cord.
9.	DO NOT insert or allow foreign objects to enter any
	ventilation or exhaust opening as this may cause an electric
	shock or fire, or damage the heater.
10.	DO NOT operate heater with a damaged cord or plug, or
	after the heater malfunctions, or has been damaged in any
	manner. Return appliance to manufacturer for examination,
	electrical or mechanical adjustment, or repair.

CONSUMER SAFETY INFORMATION

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician

to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

TECHNICAL SPECIFICATIONS

	Amps:	12.5
	Wattage:	1500W/ (+ 5% - 10%)
	Working Voltage:	120V AC/60 HZ
	Bulb Type:	(2) 25W max Candelabra Base

Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps.

ASSEMBLY INSTRUCTIONS

Please make sure to check packaging for parts that could be used to operate your heater.

This package includes:
1	- Fireplace Heater	2	- Light bulbs
1	- Remote Control	2	- AAA Batteries for Remote
1	- Stand	4	- Machine Screws (for stand)
1	- Wall Mount Hardware Kit

Installing Batteries into the Remote:

Before operation, insert 2 “AAA” batteries into the back of the remote control:

• Do not mix old and new batteries

Stand Assembly:

For floor use attach the Stand to the Fireplace heater using the 4 machine screws (provided). Gently lay the unit on the floor and attach the Stand to the bottom For wall mount see Wall Mount Instructions below.

Wall Mount Installation:

This product weighs 25 lbs. Do not install alone.

Mounting Template with instructions is attached below to make mounting your Fireplace Heater easy.

• Wall Mount Hardware Kit includes:

4 - 1.5” Phillips head self tapping screws

4 - toggle bolts

2 - mounting brackets

IMPORTANT: Before drilling into any wall ensure no electrical cables are present in the area.

Max. height of 47” (1.2 m).

Make sure you allow at least 3 feet (1m) of space on the sides of unit.

Brackets

3 ft.

3 ft.

3 ft.

minimum

OPERATING INSTRUCTIONS

•There may be an odor coming from the heater the first time you use it. This is normal during the break-in period. Make sure the heater is in a well ventilated area and continue running it until the smell goes away.

•You may hear a popping or crackling sound as the heater heats up. This is normal and safe operation.

•The Fireplace Heater can be operated by using the remote control (Fig. 1) or the control panel (Fig. 2) located on the top of the unit.

•Place the heater on a firm, level surface or mount on wall.

•Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps.

Power On/Off

Turn Power ON. LCD and Power Light will illuminate. The units default settings are: Temperature 80°; Timer OFF; Flame Brightness HIGH; Sound ON.

Thermostat

•Press Thermostat button until desired temperature level appears on LCD Display. It is recommended to start by setting the temperature to the highest setting. When your room reaches the desired comfort level, lower the thermostat until the heat stops and thermostat light turns off. Note: the fan will continue to run for flame operation.

•The system now maintains the selected comfort level by automatically turning the heater ON and OFF. The Thermostat light cycles ON and OFF with the heater element as it maintains the programmed temperature.

•When LCD reads 00 the heat will turn off but the fan will continue to run for flame operation.

Timer

You can set the timer to automatically turn the unit off. Press the Timer button, select between 1 and 12 hours. Your selection will then be displayed on the LCD.

Key to Icons

On/Off

Thermostat

Timer

Flame Brightness

Sound

Fahrenheit/Celsius

Remote Control

Fig. 1

Control panel

FRONT	LCD	Power
Control
Panel	Display	Light
Buttons

Glass	Heat	Removable
Panel	Vent	Stand

BACK

Handle

Hanging

Brackets

11.	A heater has hot and arcing or sparking parts inside. DO
	NOT use it in areas where gasoline, paint, or flammable
	liquids are used or stored.
12.	Use appliance only for intended household use as described
	in this manual. Any other use not recommended by the
	manufacturer may cause fire, electric shock, or injury to
	persons. The use of attachments not recommended or sold
	by the manufacturer may cause hazards.
13. DO NOT use outdoors.
14.	To prevent a possible fire, DO NOT block air intakes or
	exhaust in any manner. DO NOT use on soft surfaces like a

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (nickel-cadmium) batteries

The remote control for this unit has the capability of operating all control panel functions. Please note this remote will not work through walls.

Bulb Placement:

Unwrap the two 25W Candelabra Bulbs from cardboard insert found at the top of unit and open doors on back of unit with a screwdriver.

1.Remove stand from main unit, if installed.

2.Secure the mounting brackets to the wall using the Wall Mounting Template provided (see below).

3.Hang main body on wall brackets by lifting over the bracket and sliding down.

4.Use Cord Wrap to hide extra cord.

Flame Brightness

There are four flame brightness settings: High, Medium, Low, Off. Press button to select desired brightness.

Sound

Press Sound button to adjust 4 sound levels or turn crackling sound on or off.

Fahrenheit/Celsius

Press to show temperature in Fahrenheit or Celsius.

Fig. 2	(Back of Heater)
	(Front of Heater)

Light Bulbs Cord Wrap

	bed, where openings may become blocked.
15.	To disconnect heater, press the On/Off button, then remove
	plug from outlet.
16.	Avoid the use of an extension cord because the extension
	cord may overheat and cause a risk of fire. However, if you
	have to use an extension cord, the cord should be No.
	14AWG minimum size and rated not less than 1875 watts.
17.	If the heater will not operate, see specific instructions under
	Auto Safety Shut-off on resetting the heater.
18.	DO NOT attempt to repair or adjust any electrical or
	mechanical functions on this unit. Doing so will void your
	warranty. The inside of the unit contains no user serviceable
	parts. All servicing should be performed by qualified
	personnel only.
19.	DISCONTINUE USE IF PLUG OR OUTLET IS HOT.
	RECOMMEND OUTLET BE REPLACED IF PLUG OR
	OUTLET IS HOT TO TOUCH.

PLEASE SAVE THESE INSTRUCTIONS

0 inches 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

BRACKET	Wall Mounting Template
Mark for
Drill
				Drilled	Bolt
				Hole
GUIDE					Toggle
	Included for mounting:	To mount into wall studs	To mount into drywall	Wall	Bracket
	4 - 1.5” (38 mm) Phillips	1. Find studs in wall. Studs are typically 16” (40 cm) apart.	Use toggle bolts for 3/8 - 5/8” (10 – 16 mm) thick drywall.
	head self tapping screws	2. Cut Mounting Template on dotted line and tape onto wall so	1. Cut Mounting Template on dotted line and tape onto wall. Use level to make
		brackets are centered on studs.	sure template is level and mark wall with a sharp object such as an awl.

	4 - toggle bolts	3. Use level to make sure template is level. Using a sharp object	2. Drill 3/8” (10 mm) holes at top and bottom of bracket guide in center of studs.
	2 - mounting brackets	such as an awl, mark hole location.	3. A - Align bolts, through bracket holes then thread on Spring Loaded Wings.
		4. Using a Power Driver with Phillips head bit, drive 1.5” (38 mm)	B - Collapse Wings while pushing through hole in wall.	Spring
		screws through bracket and drywall into wood or metal stud.	C - Pull bolt out to secure Toggle Wings against inside of wall (wings spring	Loaded
		IMPORTANT: Before drilling into any wall ensure no	open on other side of wall and securely hold bolt and bracket).	Toggle	Wall
		electrical cables are present in the area.	D - Screw bolt in until tight.	opens on
				inside of
Mark for				wall
	Note: The mounting hardware included is intended for mounting the heater on 3/8” to 5/8” (10 – 16mm) drywall affixed to wood or metal studs. For your convenience the wall mount
Drill
	brackets are 16” (40 cm) on center to align with 2 studs. Not all studs will be 16” (40 cm) on center. If you are not able to align with studs, toggle bolts are provided. For other wall types,
	please consult a professional or visit your local hardware store to determine which type of hardware is best for your particular wall.

16

Mark for

Drill

BRACKET

GUIDE

Mark for

Drill