Bionaire BAP1225-U, BAP1250-U warranty Instruction Leaflet, MODEL BAP1225-CN BAP1250-CN

BAP1225/1250CN04EFM1.qxd 11/17/04 3:51 PM Page 1

EnviroCheckTM

99.97% HEPA

Air Cleaner

MODEL BAP1225-CN

BAP1250-CN

AIR CLEANER SAFETY

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using appliance.

• To avoid fire and shock hazard, plug the air cleaner and

EnviroCheckTM Wireless Air Quality Center directly into 120V

AC electrical outlets.

• If the filter is covered by a bag when shipped: remove plastic

bag before use.

• Keep the cords out of heavy traffic area. To avoid fire hazard

NEVER put cords under rugs, near heat registers, radiators,

stoves or heaters.

• To protect against electrical hazards DO NOT immerse in

water or other liquids. Do not use near water.

• Close supervision is necessary when any appliance is used by

or near children or disabled persons.

• Always unplug the air cleaner or EnviroCheckTM Wireless Air

Quality Center before moving it, opening the grill, changing

the filters, cleaning the IR Lens or whenever the appliances

are not in use. Be sure to pull by the plug and not the cord.

• NEVER drop or insert any object into any openings.

• Do not operate any appliance with a damaged cord or plug, if

motor fan fails to rotate, after the appliance malfunctions, or if it

has been dropped or damaged in any manner. Return appliance

to manufacturer for examination, electrical or mechanical

adjustment or repair.

• Use appliance only for the intended household use as

PLEASE SAVE THESE INSTRUCTIONS

CONSUMER SAFETY INFORMATION

THIS PRODUCT IS EQUIPPED WITH A POLARIZED PLUG (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to

install the proper outlet.

DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG IN ANY WAY.

The length of the cord used on this product was selected to reduce the hazards of becoming tangled in, or tripping over a longer cord. If a longer cord is necessary an approved extension cord may be used. The electrical rating of the extension cord must be equal to or greater than the rating of the air purifier. Care must be taken to arrange the extension cord where it cannot be pulled on by children or accidentally tripped over.

FEATURES

Dual Position – The air cleaner can stand upright or lie on its side. Also designed to fit with its back flush against the wall. When positioning the unit, please be sure the air inlet and air outlets are not blocked to ensure maximum airflow.

Three Levels of Filtration:

Washable Foam Pre-Filter – Captures larger particles like pet dander and prolongs the life of the HEPA and CARBON filters.

Carbon Filter – Helps reduce household odors and remove larger particles.

HEPA Filter – Removes 99.97% of airborne particles as small as

0.3 microns from air passing through the filter. This includes things

like smoke, dust, pollen, ragweed, grass-

Advanced Communication Technology – Radio frequency technology sends continuous signals between air cleaner and EnviroCheckTM Wireless Air Quality Center.

Sensor Control Mode – When set to Sensor Control auto mode, the sensor measures your indoor air quality and adjusts the fan speed automatically to provide optimum filtration. It also helps conserve energy by only operating the fan at higher speeds when needed.

Remote Operation – The function of the
EnviroCheckTM Wireless Air Qulaity Center
is similar to a remote control. From across	on/off
the room, you can operate your air cleaner		HI		PM
- you can change speed settings, turn off		ON TIMER		PM
the appliance or set to sensor control.	mode	SENSOR	CONTROL
Programmable Controls – Gives you the		timer set	clock	alarm
flexibility to program your air cleaner to turn
on and off at your convenience.

Clock/Alarm Mode – Convenient clock

and alarm mode make the EnviroCheckTM Wireless Air Quality Center multi-functional. Replaces tabletop or nightstand clock. Also features a 10 minute snooze alarm.

This product earned the ENERGY STAR by meeting strict energy efficient guidelines set by the US EPA. The energy efficiency of the ENERGY STAR qualified model is measured based on a ratio between the model’s CADR for dust and the electrical energy it consumes, or CADR/ Watt.

PRE-OPERATING INSTRUCTIONS

1.Carefully unpack your air cleaner. Select a firm level place where there are no obstructions to the air inlet or filtered air outlet. A good location in a room is approximately one foot away from the wall, in a central location of your home.

2.Open the door of the air cleaner by carefully placing fingers in the indentation on the right side of the door and gently pull forward.

3.The carbon filters, which are packed in a plastic bag in the box, should be removed from plastic bag and then placed on each of the HEPA filters. The plastic tabs on the HEPA filter will hold the carbon in place. (Figure 1)

3.Synchronize the appliances by simply pressing the on/off button on the EnviroCheckTM Wireless Air Quality Center. The air cleaner will beep in rapid succession for a few seconds. The EnviroCheckTM Wireless Air Quality Center is now ready to operate with your air cleaner.

PROGRAMMING INSTRUCTIONS

CLOCK

When the EnviroCheckTM Wireless Air Quality Center is plugged into the electrical outlet, the time will automatically set for 12:00 am. After the clock has been set it will show current time as long as the appli- ance is plugged in.

1.To set the clock time, press the “CLOCK” and “SET” buttons at the same time. The hour numbers will begin to flash.

2.Press “+” or “-“ to set desired hour., then press “SET”.

3.When a button has not been pressed for a few seconds OR when the “SET” button is pressed again, the minute numbers will begin to flash.

4.Press the “+” and “-“ buttons to adjust the minutes as indicat- ed above in step 2.

5.When a button has not been pressed for a few seconds OR when the “SET” button is pushed again the clock will begin operating.

ALARM

The EnviroCheckTM Wireless Air Quality Center is equipped with an alarm clock option.

Setting Alarm	HI	PM
		ON TIMER

1.	To set the alarm, press the “ALARM” and				PM
	“SET” buttons at the same time. The hour	de	SENSOR CONTROL
	numbers will begin to flash and a small bell	timer	set	clock	alarm
	will appear in the bottom right hand corner
	of the LCD screen.
2.	Press “+” or “-“ to set desired hour., then press “SET”.
3.	When a button has not been pressed for a few seconds OR
	when the “SET” button is pressed again, the minute numbers

Programmable Timer

The EnviroCheckTM Wireless Air Quality Center has a programmable timer feature. You can program the air cleaner to turn on and off at your convenience. NOTE: The EnviroCheckTM Wireless Air Quality Center must be used to turn the air cleaner on, set the operating speed, and turn air cleaner off in order for the timer to work. (Steps 1-3 below)

1.	Using the EnviroCheckTM Wireless Air Quality Center turn the
	air cleaner on by pressing the “ON/OFF” button. (See
	Operating Instructions below for more details.)
2.	Set the desired operating speed by using the “MODE” button.
3.	Then using the EnviroCheckTM Wireless Air Quality Center turn
	the air cleaner off by pressing the ”ON/OFF” button.
4.	To program the timer press the “TIMER” and “SET” buttons
	at the same time.
	a)	Set the “Timer On” time first: To set the time the air
		cleaner will come on, press the “TIMER” and “SET”
		buttons at the same time. The hour numbers in the
		timer section will begin to flash.
	b)	Press “+” or “-“ to set desired hour., then press “SET”.
	c)	When a button has not been pressed for a few seconds
		OR when the “SET” button is pressed again, the minute
		numbers will begin to flash.
	d)	Press the “+” and “-“ buttons to adjust the minutes as
		indicated above in step 2.
	e)	When a button has not been pressed for a few seconds
		OR when the “SET” button is pushed again the timer
		“ON” will be set and the Timer “OFF” will begin flashing.
	f)	Set the “Timer Off” time second by following instructions
		in step 4a - e.
5.	After completing timer set operation the “TIMER ON” and
	programmed time will be displayed.
6.	Once the unit has begun operating in timer mode the “TIMER
	OFF” and programmed off-time will appear in the top display.
7.	To turn off the programmable timer press and hold the

described in this manual. Any other use not recommended by

Read instructions before operating.

Retain for future reference.

Instruction Leaflet

the manufacturer may cause fire, electrical shock or injury to

persons. The use of attachments not recommended or sold

by The Holmes Group may cause hazards.

• Do not use outdoors.

• Never block the air openings, or place on soft surface, such

as bed or sofa, as this could cause the unit to tip over thus

blocking the air intake opening.

• EnviroCheckTM Wireless Air Quality Center should only be used

in a room with temperatures between 40° F and 110° F

• Keep appliances away from heated surfaces and open flames.

• DO NOT attempt to repair or adjust any electrical or

mechanical functions on these appliances. Doing so will void

the warranty. The inside of these appliances contain no user

serviceable parts. All servicing should be performed by

qualified personnel only.

es, mold spores, dust mite debris and

pet dander.

Carbon Filter Indicator – When the carbon filter indicator light turns red it is time to change the carbon filters.

HEPA Filter Indicator – The filter life monitor uses a series of lights to give you an indication of the remaining filter life. With new filters the bottom light will

be illuminated green. As the filter life progresses the filter life indi- cator will move to yellow and your HEPA filters should be checked for particulate accumulation. When the filter life indicator light is red, it is time to change the HEPA filters.

EnviroCheckTM Wireless Air Quality

Center – Multifunctional providing an indoor air quality display, auto mode, programmable controls, remote operation of air

4.This model utilizes a hang tab. The filter should easily slide onto the filter hang tab with only a small amount of pressure. (Figure 2)

NOTE: The side with the soft gasket should face inward.

5.Replace the front grill by swinging door closed and gently press until front grill is firmly in place.

6.Carefully remove your EnviroCheckTM Wireless Air Quality Center from the packaging materials.

7.Select a firm level place on a tabletop or counter where there are no obstructions to the venting holes.

Figure 1

Figure 2

	will begin to flash.
4.	Press the “+” and “-“ buttons to adjust the minutes as indicat-
	ed above in step 2.
5.	When a button has not been pressed for a few seconds OR
	when the “SET” button is pushed again the time will appear
	on the LCD screen and the alarm is set. A small bell will now
	appear in the bottom right hand corner indicating the alarm is
	operational.
6.	To check the alarm setting, press the “ALARM” button. The
	alarm set time will appear. Press the “TIME” button to return
	to clock mode.

Turning Alarm OFF

1.	When the alarm goes off, a rapid beeping will be heard.
2.	To deactivate the alarm press the “ALARM” and “SET” buttons at
	the same time. The bell in the right hand corner will disappear.

☎ INFO-LINE

If after having read this leaflet, you have any questions or comments on your air cleaner, call 1-800-253-2764in North America.

•	WARNING: To reduce the risk of fire or electrical shock, DO
	NOT use these appliances with any solid-state speed control
	device.
•	DO NOT place anything on top of these appliances.

cleaner as well as a clock and alarm mode.

Air Quality Sensor – Uses an advanced infrared optical system to constantly detect tiny airborne particles in the air around the EnviroCheckTM Wireless Air Quality Center, such as pollen and dust. It displays the air quality conditions using a series of LED lights glowing red when high levels of particles are present and green when air quality is improved.

SYNCRONIZING INSTRUCTIONS

1.Plug the air cleaner into a 120V AC electrical outlet. The air clean- er will begin to beep continuously until it is synchronized with the EnviroCheckTM Wireless Air Quality Center.

2.Plug the EnviroCheckTM Wireless Air Quality Center into a 120V AC electrical outlet near the air cleaner. It will beep once. NOTE: EnviroCheckTM Wireless Air Quality Center is designed to operate up to 30 feet from air cleaner.

3.	The longer the alarm sounds the louder it gets.
4.	The alarm has a snooze feature. Press the “ALARM” button
	when the alarm is sounding and the alarm will turn off. After 10
	minutes, the alarm will sound again. The alarm will continue to go
	off every 10 minutes until the alarm mode is deactivated. See
	step 2 above.

3.Select the desired operating speed. This Bionaire® Air Cleaner has four speed settings. You can select from <<HIGH>> ( ),

<<MED>> ( ), <<LOW>> ( ) or <<SLEEP>> ( ) by pressing the “MODE” button on either the air cleaner control panel or the EnviroCheckTM Wireless Air Quality Center.

4.The light on the control panel will illuminate letting you know the power is on and at what speed the air cleaner is operating.

5.For optimum air filtration, it is recommended to operate the air cleaner continuously. Its rugged motor has been designed to provide many years of continuous use.

For continuous use, it is recommended to operate the air cleaner on the LOW or MEDIUM setting. For quieter operation or use in a bedroom, select the LOW or ultra-low SLEEP setting. When high levels of air pollution are present, select the HIGH setting to quickly circulate and filter the room air.

NIGHTLIGHT

Your EnviroCheckTM Wireless Air Quality Center has a built in nightlight which automatically turns on as your room gets dark. To turn off this nightlight press the "+" and "-" buttons at the same time. To turn this function back on simply press both buttons again. NOTE: When any button is pressed the backlight will come on for a few seconds. Once no buttons are pressed again for 5 seconds the light will go off.

Air Quality Sensor

Your Bionaire® Air Cleaner comes with an Air Quality Sensor which uses an advanced infrared optical system to constantly detect tiny particles in the air around the EnviroCheckTM Wireless Air Quality Center such as pollen and dust. It also displays the air quality even when the air cleaner is turned off, using a series of colored lights. Radio frequency technology sends continuous signals between air cleaner and the EnviroCheckTM Wireless Air Quality sensor and adjusts air cleaner to improve air quality wherever it is placed.

•The air quality sensor uses a series of lights to indicate air quality conditions and particle levels. The lights range in color from green which indicates good air quality conditions or low levels of airborne particulate to red which shows poor air quality conditions or high levels of airborne particulate.

•The air quality sensor operates continuously when the EnviroCheckTM Wireless Air Quality Center is plugged into a 120V AC outlet, even when the air cleaner is turned off.

Sensor Control Mode

When the EnviroCheckTM Wireless Air Quality Center is in the “Sensor Control” mode, it will automatically adjust the fan setting to the optimum speed based on the air quality conditions and particle levels in the air. As the particle concentration in the air rises, so does the speed. In sensor control mode, the unit will always run at a minimum of SLEEP speed even if the particle levels are low to maintain ideal conditions.

1.To turn the air cleaner onto “Sensor Control” mode you must use the EnviroCheckTM Wireless Air Quality Center.

2.Turn the air cleaner on using the Operating Instructions. Select the desired operating speed by scrolling through the settings using the “MODE” button. You can select from “HI”, “MED”, “LOW”, “SLEEP” or “Sensor Control”.

3.Once in “Sensor Control” mode, the air cleaner speed will fluctuate depending on airborne particulate concentration.

NOTE: The Sensor Control mode can not be controlled from the air cleaner control panel. It can only be controlled using the EnviroCheckTM Wireless Air Quality Center.

CLEANING/MAINTENANCE INSTRUCTIONS

Air Cleaner Maintenance Instructions

Turn off and unplug the unit before cleaning.

1.	The outside of the air cleaner can be cleaned with a soft,
	damp cloth.
2.	The filtered air outlet/top air vent can be cleaned of dust with
	a small, soft brush.
3.	You can remove the air inlet/front grill for cleaning by open the
	door of the air cleaner. Carefully placing fingers in the indentation
	on the right side of the door and gently pull forward. With
	door open to 90 degrees pull grill up and forward. Once
	removed front grill can be cleaned with warm soapy water. Do
	not place in dishwasher. Make sure the grill is completely dry
	before reinstalling. (Figure 3)
4.	If you wish to clean the inside of the	Figure 3
	air purifier, please remove filters and
	only use a dry, soft cloth to wipe it
	down.
5.	DO NOT wash HEPA or CARBON
	filters.
WARNING: Do not allow moisture to		STEP 2
come in contact with the main housing			STEP 1
of the air cleaner.

Pre-Filter Cleaning Instructions

1.Every 2-3 weeks check the conditions of the washable foam pre-filter.

2.Open the front door and remove the pre-filter frame to exam- ine the pre-filter. (see figure 3)

3.If the pre-filter has a noticeable amount of dust, lint or particu- late accumulation, wash it by hand in warm soapy water. The pre-filter must be washed at least every 30 days or more often as necessary. If the pre-filter is worn or damaged replace it. DO NOT wash in an automatic washer. Gently hand wash only.

4.After washing, rinse and dry the pre-filter thoroughly before replacing it into the air cleaner door. DO NOT dry the pre-filter in an automatic dryer. Hand dry only by dabbing gently with a hand dry cloth towel.

5.Replace pre-filter in door and latch pre-filter frame (see figure 4).

Filter Life Indicators	Figure 4
The HEPA Filter life indicator uses a
series of lights to give you an
indication of the remaining filter life. With
new filters, the lights on the air cleaner
display will be illuminated green. As filter
life progresses the filter life indicator will
move to yellow. When the filter light is
red, it is time to change the HEPA filters.
There is also a carbon filter indicator light

on the air cleaner control panel. When this light illuminates red, it is time to change the Carbon filters.

FILTER REPLACEMENT INSTRUCTIONS

On average, HEPA filters need to be replaced every 12-18 months. Carbon filters need to be replaced every 3-6 months. Filter life will vary depending on air quality and usage.

1.Turn off and unplug your air cleaner before attempting to replace the filters.

2.Remove each of the filters from the unit by pulling gently towards you.

3.To replace the carbon filter, simply remove the old carbon filter and using the plastic tabs as a guideline (see Figure 1), insert a new carbon filter in its place after removing the plastic bag.

4.To replace the HEPA filter, discard the old HEPA filters. DO NOT attempt to clean. Put the carbon filter back on the new HEPA filter. Insert the new HEPA filter into the unit, by sliding it on the hang tabs (see Figure 2).

5.After replacing the filters, RESET the appropriate Filter Life Indicator by inserting a small object (such as a pin or paper clip) into the hole below the filter change light. The series of

LED lights is the HEPA ( ) filter indicator and the red LED is the carbon () filter light.

NOTE: The side with the soft gasket should face inward.Replacement filters are available from your local suppli- er or by calling 1-800-253-2764.

Air Cleaner	Filter Quantity	Filter #	Filter
Model #	Needed		Description
BAP1225-CN	2	A1230H	HEPA
	2	A1260C	Carbon
BAP1250-CN	3	A1230H	HEPA
	3	A1260C	Carbon

Air Quality Sensor Cleaning Instructions

It is recommended that you clean the air quality sensor monthly to maintain accurate monitoring or particulate levels.

1.The air quality sensor is located on the back side of the EnviroCheckTM Wireless Air Quality Center.

2. Open the sensor door (Figure 5)

3. Use a dry cotton swab to gently clean the

sensor lens. Do not use any water or cleaning Figure 5 agents.

4.Securely close the sensor door. If it is not closed the sensor may not operate properly.

TROUBLESHOOTING

Problem	Solution
Air Cleaner will	• Check to make sure air cleaner is
not operate	properly plugged in.
	• Check to make sure the air cleaner is
	on by pressing the on/off or (		) button.
	• Check the filters to see if they are in
Decreased air flow	good condition and if they need to be
	changed.
	• Check to ensure nothing is blocking
	air inlet and filtered air outlet.
EnviroCheckTM	• Make sure the EnviroCheckTM Wireless
Wireless Air Quality	Air Quality Center is synchronized with
	the air cleaner by following
Center is not
	synchronization instructions.
controlling unit	• The Air Cleaner and EnviroCheckTM
	Wireless Air Quality Center can be re-
	synchronized by holding down the
	ON/OFF (	) button on both the Air
	Cleaner and the EnviroCheckTM
	Wireless Air Quality Center at the same
	time for 5 seconds until you hear a rapid
	beeping sound.
Air Quality Sensor	• Chances are there are low levels of
lights are always	airborne particles around the sensor.
green	This should not be a concern.

SERVICE INSTRUCTIONS

1.Do NOT attempt to repair or adjust any electrical or mechani- cal functions on this unit. Doing so will void the warranty. The inside of the unit contains no user serviceable parts. All servic- ing should be performed by qualified personnel only.

2.If you need to exchange the unit, please return it in its original carton, with a sales receipt, to the store where you purchased it. If you are returning the unit more than 30 days after the date of purchase, please see the enclosed warranty.

3.Should your Air Cleaner require service, please call

1-800-253-2764 in North America for further assistance.

4. If you have any other questions or comments, feel free to write to us:

Consumer Service Department

32B Spur Drive

El Paso, TX 79906

Visit our website at www.bionaire.com

TWO (2) YEARS FULL WARRANTY

Manufacturer warrants for TWO (2) YEARS from the date or original purchase, to repair or, if repairs are not commercially applicable to replace without charge (parts and labor), any supplied or manufactured part of this air cleaner which, upon inspection by an authorized service center, proves to have failed in normal use due to defects in material or workmanship, or, at its option, to replace the unit. If the product can not be reasonably repaired, the consumer may elect a free replacement or refund.

Operations under conditions other than those recommended or at voltages other than the voltage indicated on the unit, or any attempts by unauthorized personnel to service the unit or modify it, will render the guarantee void.

Manufacturer shall not be liable for any personal injury, property damage or any incidental or consequential damages of any kind (including water damage), resulting from defects, malfunctions, misuse, improper installation or alteration of the product.

MANUFACTURER EXPRESSLY DISLAIMS ALL REPSONSIBILITY FOR CONSEQUENTIAL DAMAGES OR INCIDENTAL LOSSES FOR BREACH OF EXPRESS OR IMPLIED WARRANTIES CAUSED BY USE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE.

The provisions of this warranty are in addition to and not a modification of or subtraction from the statutory warranties and other rights and remedies contained in any applicable legislation and to the extent that any such provision purports to disclaim, exclude or limit any such statutory warranties or other rights or remedies, such provisions shall be deemed to be amended to the extent necessary to comply therewith.

For Warranty Service, please call 1-800-253-2764.

A Bionaire® customer service representative will help determine which is the best procedure in order for your air cleaner to be repaired.

KEEP THIS NUMBER FOR FUTURE REFERENCE

RADIO FREQUENCY COMPLIANCE INFORMATION

Operation is subject to the following two conditions:

1.This device may not cause interference.

2.This device must accept any interference, including interfer- ence that may cause undesired operation of the device. Modifications not authorized by the manufacturer may void user 1st authority to operate this device.

Bionaire® , the Bionaire logo® and EnviroCheckTM are trademarks of The Holmes Group, Inc. or its subsidiary.

Printed In China

"TIMER" button for 3 seconds.

NOTE: If the air cleaner is turned on before timer mode begins, the unit will remain on and “TIMER OFF” will appear on the display. The air cleaner will still turn off as programmed.

EnviroCheckTM Wireless Air Quality Center

The EnviroCheckTM Wireless Air Quality Center serves as a command center for the air cleaner. It remotely operates the air cleaner by sending continuous signals from the EnviroCheckTM Wireless Air Quality Center to the air cleaner. This one way communication can be overridden by operating the controls directly on the air cleaner. When using the EnviroCheckTM Wireless Air Quality Center, the yellow LED on the air cleaner will illuminate. When operating controls directly on the air cleaner, the Yellow LED light will turn off. To resume primary control from the EnviroCheckTM Wireless Air Quality Center, press the ”ON/OFF” or “MODE” button. The Yellow LED light on the air cleaner will again illuminate.

Operating Instructions

1.The air cleaner can be operated from either the control panel directly on the air cleaner or the EnviroCheckTM Wireless Air Quality Center.

2.To turn the air cleaner on, press the “ON/OFF” button on the

EnviroCheckTM Wireless Air Quality Center OR press the () on the air cleaner.