BW2100_2100R07EM1. qxd:BW2100_2100R07EM1. qxd 11/19/07
FAN SAFETY
PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be taken including the following:
1.Read all instructions before using this appliance.
2.Use fan only for purposes described in the instruction manual.
3.To protect against electrical shock do not immerse unit, plug or cord in water or spray with liquids. Plug the appliance directly into a 120V AC electrical outlet.
4.Close supervision is necessary when any appliance is used by or near children.
5.Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.
6.Avoid contact with moving parts.
7.DO NOT operate in the presence of explosive and/or flammable fumes.
8.To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
9.DO NOT operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner.
10.The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
11.DO NOT use outdoors.
12.DO NOT let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas.
13.To disconnect, grip plug and pull from wall outlet. Never yank on cord.
14.Always use on a dry, level surface.
15.DO NOT operate fan until fully assembled with all parts properly in place.
16.This product is intended for household use only and not for commercial or industrial applications.
4:51 PM Page 2
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS APPLIANCE HAS A POLARIZED AC PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
INSTALLATION INSTRUCTIONS
Carefully unpack contents from carton.
A 
I
A. Front Grill | G. Fan Directional Switches (2) |
B. Control Panel | H. Built-in Extender Screen |
C. Mode Button | I. Extender Locks (2) |
D. LED Display | J. Extender Panels (2) (not shown) |
E. Temp Up (+) | K. Remote Control (For BW2100R |
F. Temp Down (-) | only - not shown) |
| |
FOR DOUBLE-HUNG AND SLIDER WINDOWS
NOTE: FOR SLIDER WINDOW, SET THE FAN VERTICALLY IN YOUR WINDOW OPENING WITH THE LEFT SIDE OF THE FAN SITUATED ON THE BOTTOM AND THE BUILT-IN EXTENDER SCREEN FACING UPWARDS.
1.Set the fan into your window opening (note that the window screen does not have to be removed or left open.)
2.If the fan does not fit snugly to the top and bottom of the window casing, attach the “Extender Panel(s)” and adjust the built in extender screen until the fan fits safely in your window. (See Figure 2)
3.To keep the fan in place, carefully close the window so that the bottom edge of the window rests on the flat area at the flat top of the fan.
FIGURE 2 | FRONT VIEW |
|
| LEFT | RIGHT |
Extra Extender Panels | Built-in Extender, pull out |
4.25 inches (10cm) - | up to 7 inches (17cm) |
2 pieces included in
your box
UNIT’S LENGTH
WARNING: BE SURE FAN IS SECURELY INSTALLED IN YOUR WINDOW AT ALL TIMES. DO NOT LEAN OR PUSH ON FAN WHILE IT IS IN THE WINDOW.
OPERATING INSTRUCTIONS
1.Plug cord into any standard 120 volt AC outlet. Please make sure the speed control is in the off position.
2.To turn the fan on and control the speed, press the mode button. Note that pressing the mode button will allow you to cycle through the speed setting (High=3, Med=2, Low=1) as well as the Automatic Thermostat Temperature settings (Auto High = A3, Auto Medium = A2, Auto Low = A1). 0 indicates the Off position.
3.Set the airflow direction by sliding the fan directional switches located above each fan blade. Note that the fan blades work independently from one another and can be used for air intake (bring fresh air in from outside), exhaust (push air out from within the room) or exchange (cycles air in and out of the room simultaneously).
AUTO MODE
Your fan is equipped with a Programmable Digital Thermostat that will automatically turn the fan ON and OFF depending upon the preset comfort temperature. This is ideal for night time operation when temperatures can drop below comfort levels.
For example, if you set your fan to 75 degrees and the temperature drops to 74 degrees then the fan will automatically turn off. The fan will automatically turn on again when the room temperature exceeds the set temperature.
SETTING AUTO MODE
1.Press the Mode button to scroll to the desired auto speed setting (A3, A2, or A1).
2.Choose the desired temperature setting by pressing the Temp Up (+) or Temp Down (-) buttons. You may select a temperature between 60 and 80 degrees Fahrenheit. Once the desired temperature is set, the digital display will return to show the ambient room temperature. View the set temperature by pressing either the Temp Up (+) or Temp Down (-) buttons.
IMPORTANT: If the fan does not start in the Auto mode, please be sure that the set temperature is below the current room temperature. Lower the set temperature if you would like the fan to start or switch over to the manual speed modes.
SETTING THE TIMER
1.Hold both the Temp Up (+) and Temp Down (-) buttons down until the digital display flashes “00”.
2.Press the (+) or (-) buttons to change time in 1 hour increments. Note selection ranges from 1 to 16 hours. When in the timer mode, the time remaining will be displayed.
NOTE: If Timer is set when fan is ON, the time displayed will turn the fan OFF once elapsed. If Timer is set when fan is OFF, the time displayed will turn the fan ON.
(The default ON speed setting is Manual Low).
NOTE: Timer function can be turned off by pressing the MODE key at any time.
REMOTE CONTROL (FOR BW2100R ONLY)
Your remote control requires (2) AAA batteries (included) for operation. To install the batteries, simply depress the back of the remote with your thumb on the indentations. Insert batteries according to the diagram shown inside and replace cover. The remote controls the Mode, Speed, Temperature, and Timer settings.
•Do not mix old and new batteries.
•Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
