Black & Decker 90518515 instruction manual Assembly Instructions

9

11

13

10

12

14

CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence.

1.Angle unit as shown in figure 7.

2.Slowly swing trimmer side-to-side as shown in figure 8.

3.To convert for maintenance edging, turn off the tool. Holding the trimmer (as shown in figure 9) with one hand by the auxiliary handle, grasp the trimmer head collar, push in direction of arrow and rotate the trimmer head clockwise (when viewed from the switch end) until it stops, (half turn), release your hand. The tool is locked in the edger position.

4.To operate as a maintenance edger, position trimmer above sidewalk as shown in figure 10.

5.Return to trimming position by turning the tool off, pushing in direction of arrow and rotat- ing the trimmer head counter clockwise until it stops.

RELOADING LINE ST4500

USE ONLY .065 in. (1.65mm) DIAMETER NYLON MONOFILAMENT LINE. Heavier line will overload the motor and cause overheating. This line is available at your local dealer or authorized service center.

Do not use fishing line or other lines that are not recommended.

1.Unplug extension cord at trimmer.

2.Remove the bump cap by pulling up while depressing the two release tabs on the sides of the hub at the points shown in figure 11.

NOTE: It may be necessary to pull up on the cap while depressing the release tabs one side at a time.

3.Remove any broken cutting line, wrap the remaining line tight and reinsert spool into hub as follows.

a.Wind the line tight enough so that it is all below the edges of the flanges on the spool. If it extends past the flanges, it won’t fit into the hub.

b.Place the loose end of the cutting line through the gap in the spool flange as shown in figure 12. (Either gap will do but try to leave yourself about 3 or 4 inches of line to work with.)

c.Holding the line in the gap, insert the end through the eyelet in the hub and slip the spool into the hub, as shown in figure 13.

Make sure the spring is still in place in the hub. If the spool does not slip into the hub easily, press gently and pull straight out on the cutting line that protrudes through the eyelet.

4.Once the spool drops into the hub, align the release tabs on the shroud with the slots in the hub as shown in figure 14 and press the shroud into place. Be sure that both release tabs snap into place.

5.To replace the line on a spool, follow the steps below

a.Locate, on the empty spool, one of the two small holes shown in figure 15.

b.Insert the end of the line no more than 1/8 in. into the hole and begin winding the line around the spool (figure 16). Be sure to wind the line in the direction of the arrow in figure 17. Do not overfill spool. The spool holds 20 feet (6 m) of line.

c.Perform steps 3 and 4 above.

OPERATING INSTRUCTIONS FOR CATALOG # ST7600, ST7700 AUTO FEED SYSTEM

LINE FEED

Your trimmer uses .065 in. (1.65 mm) diameter, ROUND nylon line to cut grass and weeds quickly and easily. During use, the tip of the nylon line will become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of line. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. The advanced automatic line feeding mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever its required. DO NOT BUMP unit on ground in attempt to feed line or for any other purposes.

15 16

CAUTION: ALWAYS USE EYE PROTECTION.

CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence.

17

19

21

18

20

1.Angle unit as shown in figure 7.

2.Slowly swing trimmer side-to-side as shown in figure 8.

3.To convert for maintenance edging, turn off the tool. Holding the trimmer (as shown in figure 9) with one hand by the auxiliary handle, grasp the trimmer head collar, push in direction of arrow and rotate the trimmer head clockwise (when viewed from the switch end) until it stops, (half turn), release your hand. The tool is locked in the edger position.

4.To operate as a maintenance edger, position trimmer above sidewalk as shown in figure 10.

5.Return to trimming position by turning the tool off, pushing in direction of arrow and rotat- ing the trimmer head counter clockwise until it stops.

CLEARING JAMS AND TANGLED LINES

From time to time, especially when cutting thick or stalky weeds, the line feeding hub may become clogged with sap or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below.

1.Press the release tabs on the line hub cap, as shown in figure 18 and remove the cap by pulling it straight off.

2.Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool area. (If you plan to replace the spool or rewind it, this is the place to do so, otherwise, move on.)

3.Unwrap about one foot (30 cm) of line to ensure that it’s undamaged. If it is OK rewind it and insert the line end through the eyelet in the spool hub as shown in figure 19. Pull 4 in. (10 cm) of the line through the hole and maintain tension while placing the spool down into the hub with the arrow up, as shown in figure 20.

4.Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn a few degrees left and right freely). Take care to keep the line from becoming trapped under the spool.

5.Snap the hub cap back on, and power the tool on. In a few seconds or less you’ll hear the nylon line being cut automatically to the proper length.

SPOOL OR LINE REPLACEMENT

USE ONLY .065 in. (1.65mm) DIAMETER NYLON MONOFILAMENT LINE. Heavier line will overload the motor and cause overheating. This line is available at your local dealer or authorized service center.

Do not use fishing line or other lines that are not recommended.

SAVE THESE INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

ATTACHING THE GUARD AND EDGE GUIDE TO THE TRIMMER/EDGER

WARNING: The guard must always be on the tool to protect the user. NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.

Unplug the tool before attempting to attach the guard.

1.Locate the edge guide and spread it apart as shown in figure 1.

2.Attach the edge guide to the housing by locating the two ends into the holes in the housing.

3.See figure 2 for edge guide assembled on the trimmer.

4.Remove the guard attachment screw from the guard. Slip the guard onto the trimmer housing and lineup the screw hole in the guard with the screw hole in the housing

(figure 3).

5.Insert the guard attachment screw to secure the guard in place as shown in figure 4.

6.Attach extension cord to cord retainer as shown in figures 5 & 6.

OPERATING INSTRUCTIONS FOR CATALOG # ST4500 BUMP FEED TRIMMER

LINE FEED

Your trimmer uses .065 in. (1.65 mm) diameter, ROUND nylon line to cut grass and weeds quickly and easily. Cutting line will wear faster and require more feeding if the cutting or edging is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. As you use the trimmer, the string will get shorter due to wear. Gently bump the unit on the ground and the line will feed.

CAUTION: ALWAYS USE EYE PROTECTION.

1.Perform step 1 above to remove cap.

2.Remove the spool from the tool and remove and discard all line on the spool.

3.Choose either OPTION 1 or OPTION 2 below for spool or line replacement. Perform steps listed under Option 1 or Option 2, then continue with steps 4 through 6 below.

4.Insert the line end through the eyelet in the spool hub, as shown in figure 19. Pull the line through the hole to maintain tension while placing the spool down into the hub, as shown in figure 20.

5.Press the spool down GENTLY and rotate it until you feel it drop into place. (When in place, the spool will turn a few degrees left and right freely). Take care to keep the line from becoming trapped under the spool.

6.Snap the hub cap back on, and power the tool on. In a few seconds or less you’ll hear the nylon line being cut automatically to the proper length.

OPTION 1: ACCESSORY REPLACEMENT SPOOL

Use Black & Decker replacement spool Model No. AF-100. Discard old spool.

OPTION 2: REWINDING SPOOL USING BULK LINE

Bulk line for your trimmer/edger is available at extra cost from your local dealer or Black & Decker Service Center. To install bulk line, follow the steps below. (Use .065 in.

diameter ROUND line only)

1.Insert one end of the bulk line into the hole in the spool as shown in figure 21 about 1/2 in. (12 mm).

2.Hold the line in the hole and pull the rest of the line through the slot in the spool.

3.Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on the spool until the line builds up to the notches in the spool rim. Do not overfill spool. The spool holds 30 feet (10 m) of line.