7

FOR LASER SAFETY OBSERVE THE FOLLOWING CAUTIONS:

•LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE,or into a reflection

from a mirror-like surface Fig. A & B.

•AVOID EXPOSURE - LASER LIGHT IS EMITTED FROMFRONT GUARD

APERTURE.Use of controls or adjustments, or performance of procedures other

than those specified herein may result in hazardous laser light exposure.

•DO NOT DISASSEMBLE LASER MODULE.The laser is a CLASS II LASER

PRODUCT that can emit laser power up to 1 mWMAX at 650 nm, which could result

in exposure with the module disassembled. The laser unit complies with 21 CFR

1040.10 and 1040.11.

•USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATIONEXPOSURE.

•THE USE OF OPTICAL INSTRUMENTSwith this product will increase eye

hazard.

•LASER RADIATION, avoid direct eye exposure, serious eye injury can result.
•DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of
flammable liquids, gases, or dust.
•USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES.Use of any other
batteries may create a risk of fire.
•USE ONLY ACCESSORIES that are recommended by the manufacturer for your model.
•ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER,may create a risk of
injury when used on another laser.
•REPAIRS AND SERVICING MUSTbe performed by a qualified repair facility. Repairs
performed by unqualified personnel could result in serious injury.
•DO NOT REMOVE OR DEFACE WARNING LABELS.Removing labels increases the
risk of exposure to radiation.
•THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) -
104°F(40°C).
ADDITIONAL SAFETY RULES FOR THE LASER
Fig. B

For your convenience and safety the

following labels are on your tool.

Properly secure cover.
Tighten screw before use.
Sujete correctamente la tapa. Ajuste el
tornillo antes de usar la herramienta.
Fixer solidement et correctement le
couvercle. Serrer la vis avant utilisation.
CLASS 2
LASER
RADIATION WHEN
OPEN DO NOT STARE
INTO THE BEAM. L¡SER CLASE
2 EMITE RADIACI”N CUANDO EST¡
ABIERTO. NO FIJE LA VISTA EN EL HAZ.
MISE EN GARDE : RAYONNEMENT LASER
CLASSE 2 UNE FOIS L'OUTIL ALLUM…, NE PAS
FIXER DU REGARD LE FAISCEAU.
LASER RADIATION DO NOT STARE INTO BEAM. CLASS 2 LASER
PRODUCT PER EN60825-1:11994+AII+A2 Pmax-1.0mW, =633-670nm
CAUTION/ATENCI”N/ATTENTION
RADIACI”N L¡SER. NO MIRE FIJAMENTE HACIA EL RAYO.
PRODUCTO L¡SER DE CLASE 2.
RAYONNEMENT LASER. NE PAS FIXER LE FAISCEAU DU
REGARD. PRODUIT LASER DE CLASSE 2.
COMPLIES WITH 21CFR PARTS 1040.10 AND
1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO.50, DATED JULY 26,2001.
CUMPLE CON LAS NORMAS DEL C”DIGO DE
REGULACIONES FEDERALES 21CFR 1040.10 Y
1040.11, CON LA EXCEPCI”N DE LOS
APARTADOS CONFORMES AL AVISO L¡SER N∫
50, DE FECHA 26 DE JULIO DE 2001.
CONFORME AUX SECTIONS 1040.10 ET 1040.11
DU CHAP. 21 DU CFR HORMIS LES
D…ROGATIONS CONFORM…MENT ¿ LíAVIS N∞ 50
SUR LE LASER, DAT… DU 26 JUILLET 2001.
WARNING
AVERTISSEMENT
ADVERTENCIA
AVOID EXPOSURE:
Laser radiation is emited from this aperture.
EVITE LA EXPOSICI”N:
Por esta abertura se emite radiaciÛn l·ser.
…VITEZ TOUTE EXPOSITION:
Rayonnement laser Èmis de
cette ouverture.