AS182Pub1000002000R1 8/3/05 2:29 PM Page 6
MULTI-POSITION AUTO OFF
If your iron is equipped with auto shutoff:
3. Empty the water by holding the iron over a sink with the tip pointing down. Water will empty out of
30 seconds |
8 minutes |
F |
•Once it reaches appropriate temperature, it will turn off after
30 seconds of inactivity if left horizontally, or 8 minutes if left in any other position (F).
•The auto shutoff light starts blinking red to let you know that the iron has stopped heating.
•As soon as you pickup the iron, it starts heating again.
Care and Cleaning
This product contains no user serviceable parts. Refer service to qualified service personnel.
| CLEANING OUTSIDE SURFACES |
L | 1. Make sure iron is unplugged and has cooled completely. |
2. Wipe the soleplate and outer surfaces with a soft cloth dampened with water and a mild |
household detergent. Never use abrasives, |
pads that may scratch or discolor the iron. |
SURGE OF STEAM
•Horizontal
1.With Tank 1 filled with water to the MAX mark, turn the
2. To remove tough wrinkles, pump the button at
3. After cleaning, steam iron over an old cloth to remove any residue from the steam vents. |
SELF-CLEANING
To keep the steam vents free of any buildup, about once a month follow these instructions.
1. | Fill Tank 1 with water well below the MAX line. |
2. | Plug in the iron. |
G |
•Vertical
1.Hang the garment to be steamed on a clothes hanger (Curtains or drapes can be steamed once they are hung).
2.Move the selector to 
.
3.Hold the iron close to, but not touching, the fabric.
4.Pull the fabric tight in your free hand and pump the 
button as you move the iron over the fabric (G).
IRONING WITH SPRAY (TANK 2)
Using Downy Wrinkle Releaser® Liquid
3. | Turn the |
| the auto shutoff indicator light goes out and comes on again. |
4. | Turn |
| facing down. |
5. | Move the selector to | . Be careful, as hot water and steam | |
| will come out of the steam vents (M). Continue to hold the | ||
| selector in the | position until all the water has emptied, or | |
| until you feel all mineral deposits have been flushed. If | ||
| necessary, rock iron side to side and front to back. | ||
6. | When finished, release the selector, stand the iron on its heel | ||
1.Grasp tank fill cap, twist and pull off. Be careful not to pull it too hard (H).
2. Pour Downy Wrinkle Releaser® liquid into opening to fill tank (J).
3. Press 
button to apply to fabric as you iron.
4. If spray is weak, pump the button a few times.
H | Using Water Only |
|
Important: For best results, do not mix tap water with Downy
Wrinkle Releaser® liquid.
1. Repeat step 1 above.
2. Using a clean cup, fill Tank 2 with water (K).
3. Press 
button to spray water as you iron.
4. If spray is weak, pump the button a few times
EMPTYING TANK 1 AFTER IRONING (OPTIONAL)
1. Turn the
J
2. Open the
K
rest and plug it in. Heat for about 2 minutes to dry out any |
remaining water. |
CLEANING AND MAINTENANCE OF TANK 2
About once a month, to keep Tank 2 free and clear of any buildup or deposits you should follow these instructions.
1.Unplug iron.
2.Over a sink, remove the cap on Tank 2.
3.Empty any remaining contents of Tank 2.
4.Fill half of Tank 2 with warm water.
5.Replace the cap and shake the iron vigorously to remove deposits.
6.Remove the cap, empty the contents.
7.You are now ready to refill the tank with water or Downy Wrinkle Releaser® liquid.
STORING YOUR IRON
1.Unplug the iron and allow it to cool.
2.Check that the selector is set to 
.
3.Store vertically on its heel rest to prevent water leaking from the soleplate.
5 | 6 |
