Black & Decker BDV090 manual Use

ENGLISH (Original instructions)

Check the polarity of the battery posts. A positive (POS,P, +) battery post usually has a larger diameter than the negative (NEG, N, -) battery post.

Connect the positive (red) clamp from the battery charger to the positive (POS, P, +) post of the battery.

Connect the negative (black) clamp from the battery charger to the negative (NEG, N, -) post of the battery.

When disconnecting the battery charger from the battery, always:

uSwitch off and unplug the battery charger.

uRemove the negative (black) clamp first.

uRemove the positive (red) clamp last.

uRefit any insulating covers to the battery posts.

Use

Connecting the appliance with the battery clamps (fig. A)

Warning! Always disconnect the ac plug from the ac mains socket before connecting or disconnecting the appliance to or from the battery.

Warning! Never connect any of the accessory leads together as this will cause a hazard. The accessory leads should only ever be connected to the in-line connector (6).

uConnect the battery clamps (3) to the battery charger with the in-line connector (6).

uThe appliance's output leads have colour-coded battery clamps (3) (red-positive and black-negative). These connect directly to the corresponding connectors on the battery terminals.

uFollow the steps outlined in "Safety instructions" at the front of this manual.

uInsert the ac plug of the battery charger into an ac mains socket.

Connecting the appliance with the ring terminals (fig. A & B)

Warning! Always disconnect the ac plug from the ac mains socket before connecting or disconnecting the appliance to or from the battery.

Warning! Never connect any of the accessory leads together as this will cause a hazard. The accessory leads should only ever be connected to the in-line connector (6).

uConnect the ring terminals (4) to the battery charger with the in-line connector (6).

uThe output leads have crimped, colour-coded ring terminals (4) (red-positive and black-negative). The ring terminals (4) connect directly to the corresponding con- nectors on the battery terminals.

uRemove the nuts from the bolts of the battery terminal's connectors (fig. B).

uInstall the red ring terminal (4) to the bolt of the positive battery terminal connector and replace the nut.

uInstall the black ring terminal (4) to the bolt of the negative terminal connector and replace the nut.

uInsert the ac plug of the battery charger into an ac mains socket.

Connecting the appliance with the dc accessory plug (fig. A)

Warning! Always disconnect the ac plug from the ac mains socket before connecting or disconnecting the appliance to or from the battery.

Warning! Never connect any of the accessory leads together as this will cause a hazard. The accessory leads should only ever be connected to the in-line connector (6).

uConnect the dc accessory plug (5) to the battery charger with the in-line connector (6).

uInsert the dc accessory plug (5) into the vehicle's dc ac- cessory outlet.

uInsert the ac plug of the battery charger into an ac mains socket.

Charging Indicators

uRed LED (2) - bad connection, the battery is not able to accept charge or a reverse polarity connection has been detected.

uFlashing green LED (2) - good connection and the battery is charging.

uSolid green LED (2) - the battery is fully charged.

When the appliance is properly connected, the yellow LED will illuminate, indicating that the smart circuit is functioning to as- sess the status of the battery. This procedure may take up to 2 minutes if the battery voltage is lower than 12.8 Volts.

The appliance is fully automatic; it will power on when needed and power off when the battery is fully-charged.

The appliance has built-in circuit protection which guards against overcharging or short circuits.

Charging the battery (fig. C)

uSlide the charge voltage selector switch (1) to the 6V or 12V position as required.

uLeave the appliance on.

uMonitor the battery from time to time.

Note: A clicking sound may occur during the charging proc- ess, this is normal.

uWhen the solid green LED is lit, the battery is fully charged.

uRemove the ac plug from the ac mains socket.

uRemove the charging leads from the battery.

6