CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS
| NAMEPLATE RATING AMPS – 0 – 10.0 | |||||
Total Extension Cord Length (ft) | 25 | 50 | 75 | 100 | 125 150 | |
Wire Gauge | 18 | 18 | 16 | 16 | 14 | 14 |
9.Use only the supplied charger when charging your unit. The use of any other charger could damage the battery or create a hazardous condition.
10.Use only one charger when charging.
11.Do not attempt to open the charger or the unit. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.
12.DO NOT incinerate battery packs even if they are severely damaged or completely worn out.
13.Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:
a.Wash quickly with soap and water.
b.Neutralize with a mild acid such as lemon juice or vinegar.
c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a
SAVE THESE INSTRUCTIONS
IMPORTANT CHARGING SAFETY INSTRUCTIONS
CHARGING THE POWER PACKTHE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1.Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC.
2.Slide the charger onto the power pack as shown in Figure 2 & 3 and let the power pack charge initially for 9 hours. After the initial charge, under normal usage, your power pack should be fully charged in 3 to 9 hours.
3.Unplug charger, and remove the power pack. Place the power pack in the unit and be certain that it is inserted fully into the battery cavity until it “clicks” into place.
NOTE: To remove the power pack from the unit, press down on the release button on the back of the pack (Figure 4) and slide out.
IMPORTANT CHARGING NOTES
1.After normal usage, your power pack should be fully charged in 3 to 9 hours. If the power pack is
2.DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the power pack. Longest life and best performance can be obtained if power pack is charged when air temperature is about 75°F (24°C).
3.While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.
4.If the power pack does not charge
yellow pages.
5.The power pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using unit with its power pack in a depleted condition.
6.The power pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the power pack.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keep the battery pack fresh and fully charged.
NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack has not been kept on maintenance charge, it may need to be recharged before use. A battery pack may also slowly lose its charge if left in a charger that is not plugged into an appropriate AC source.
SWITCHThe switch can be operated by moving the lever from side to side. The “ON” and “OFF” positions are marked on the housing as shown in Figure 1A & 1B.
CAUTION: DO NOT POINT UNIT DISCHARGE AT SELF OR BYSTANDERS.
CAUTION: Always wear safety glasses. Wear a filter mask if the operation is dusty. Use of gloves, long pants and substantial footwear is recommended. Keep long hair and loose clothing away from openings and moving parts. THIS SWEEPER IS FOR HOUSEHOLD USE ONLY.
NOTE: Ensure the blower is switched off and the battery is removed before attaching or removing the sweeper tube.
•TUBE ASSEMBLY To attach the tube to the sweeper, line up the tube with the sweeper housing as shown in Figure 5. Push the tube into the sweeper housing until the lock button engages the lock hole in the tube.
•OPERATION
Hold the sweeper with one hand as shown in Figure 6 and sweep from side to side with the nozzle several inches above the ground. Slowly advance keeping the accumulated pile of
debris in front of you.
MAINTENANCE•CLEANING AND STORAGE TURN OFF UNIT!
CAUTION: DO NOT POUR OR SPRAY WATER ON THE UNIT.
Use only mild soap and a damp cloth to clean the unit. Never let any liquid get inside the unit; never immerse any part of the unit into a liquid.
Your sweeper should be stored in a dry place. Do not store the unit on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts.
THE RBRC™ SEALThe RBRC™ (Rechargeable Battery Recycling Corporation)
Seal on the
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel- cadmium batteries. Help protect our environment and conserve natural resources by returning the spent
Problem | TROUBLESHOOTING |
|
Possible Cause | Possible Solution | |
• Unit will not start. | • Battery not installed properly. | • Check battery installation. |
| • Battery not charged. | • Check battery charging |
|
| requirements. |
•Battery will not charge. • Battery not inserted into charger. • Insert battery into charger until red LED appears.
• Charger not plugged in. | • Plug charger into a working |
| outlet. Refer to “Important |
| Charging Notes” for more |
| details. |
| • Check current at receptacle |
| by plugging in a lamp or other |
| appliance. |
| • Check to see if receptacle is |
| connected to a light switch |
| which turns power off when |
| you turn out the lights. |
• Surrounding air temperature | • Move charger and tool to a |
too hot or too cold. | surrounding air temperature |
| of above 40 degree F(4,5°C) |
| or below 105 degree F |
| (+40,5°C). |
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
IMPORTANT
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.
SERVICE INFORMATIONAll Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service Centers are listed under
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.Balayeuse de 18 volts
GUIDE D’UTILISATION
Code de date | Numéro de catalogue : NS118, |
| NS118G, NS118L |
|
|
VISITEZ WWW.BLACKANDDECKER.COM/NEWOWNER
POUR ENREGISTRER VOTRE NOUVEAU PRODUIT.AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LAPLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE,
•Avant de faire fonctionner l'outil, s'assurer que le tube de soufflage est verrouillé en place.
•Il faut charger la pile pendant 9 heures avant d'utiliser l'outil.CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.
AVERTISSEMENT : Directives et consignes de sécurité importantes.AFIN DE RÉDUIRE LES RISQUES DE BLESSURES :•Avant toute utilisation, s’assurer que tous ceux qui se servent de l’outil lisent et comprennent toutes les mesures de sécurité et tout autre renseignement contenus dans le présent guide.
•Conserver ces mesures et les relire fréquemment avant d’utiliser l’outil ou d’en expliquer le fonctionnement à d’autres personnes.
•Ne pas pointer l'orifice de sortie de l'outil vers soi ni vers d'autres personnes.
•Éloigner les cheveux longs et les vêtements amples des ouvertures et des pièces en mouvement.
