QUICKSTARTGUIDE - NST1118/ | ST2118 |
| |
RECHARGEABLE18VOLTNiCd STRINGTRIMMER |
| ||
1) Unpack components and verify contents. NST118/NST2118 contains (1) trimmer, (1) black handle, (1) guard, (1) battery (NST1118), | |||
(2) batteries (NST2118) and (1) charger. NOTE: NST1118contains one battery. |
| A | |
2) Place battery on charge. |
|
| 9 hours |
Important: Charge battery pack for at least 9 hours to ensure a full charge is delivered to the battery. During charging the | |||
green LED will appear. When charging is complete the green LED will go off. |
|
| 9 heures |
3) Install the handle. |
|
| 9 horas |
Important: The black auxiliary handle must be installed with the | B1 | B2 | B3 |
Black & Decker logo facing up. | |||
• Press in on the buttons on both sides of the upper housing (B1). | |||
• Partially push the handle on so that it will hold the buttons in when you |
|
|
|
release them with your hand (B2). |
|
|
|
• Push the handle completely onto the housing and position it slightly until it |
|
|
|
“snaps” into place (B3). |
|
|
|
Note: If the handle is installed upside down, the adjustment button will not |
|
|
|
engage. To remove the handle, insert a nail or screwdriver into the small hole |
|
|
|
on the side of the handle, push in the spring loaded button on the opposite |
|
|
|
side of the handle, and remove the handle from the trimmer body. |
|
| C3 |
4) Install the guard. |
|
| |
Turn the trimmer upside down so that you are looking down at the spool cap. |
|
|
|
• Turn the guard upside down and slide it onto the orange tab below the |
|
|
|
motor housing as shown (C1). Make sure the tabs on the guard engage the |
|
|
|
ribs on the motor housing as shown in C2. |
|
|
|
• Continue to slide the guard on until you hear it “snap” into place. |
|
|
|
• Using a phillips screwdriver, insert the guard screw to complete the guard |
|
|
|
assembly (C3). |
|
|
|
5) Remove the tape from the line and cutting blade on the guard. |
|
|
|
6) Adjust the mode and height. |
|
|
|
Important: The trimmer ships in the box set in the edging mode. |
|
|
|
• To switch the trimmer back into trimming mode, loosen the black collar lo- |
|
|
|
cated at the top of the aluminum pole (D1). |
|
|
|
• Rotate the pole 180°. There is a position stop at 180° to indicate you are in |
|
|
|
trimming mode (D2). |
|
|
|
• You may also adjust the height of the trimmer to a comfortable operating |
|
|
|
height when the collar is loose (D3). |
|
|
|
• Tighten the collar when the trimmer is at the desired height and mode. |
|
|
|
| Edge mode | Trim mode |
|
| Mode de coupe- | Mode de taillage |
|
| bordures | Modo de poda |
|
| Modo de bordeado |
|
|
7) Once the battery is charged, slide the battery into the trimmer area as shown. | E |
| |
|
|
|
8) Depress the lock off button (as shown here) in either direction and simultaneously pull the trigger. | F |
| |
You do not need to continue to depress the lock off button during operation. |
| ||
If you have additional questions or need help, please call Black & Decker at |
|
| |
8 a.m. to 5 p.m. EST Mon. - Fri. | 1 | 2 | |
Please check instruction manual for full instructions and warnings. | |||
|