NOm sTaTemeNT
Normas Ociales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de
que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para refer-
encia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de oper-
ación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calicado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no inter-
era su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra
o supercie similar puede bloquea la ventilación, no se debe colocar en libre-
ros o gabinetes que impidan el ujo de aire por los oricios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo am-
plicadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
AC1020A/AC1021A-XMIT/ AC1021A-REC
2
OPeraTING POINTers & TrOUBLesHOOTING
AC1020A/AC1021A-XMIT/ AC1021A-REC
11
Multimode ber optic cable contains an optical ber with a light carrying “core” that
is only .0025 inches (62.5 microns) in diameter. Single mode ber optic cable has an
even smaller “core”, only 00032 to .0004 inches (8-10 microns). This is smaller than
a human hair! Therefore, any minute particles of dirt or dust can easily block the ber
from accepting or radiating light. To prevent this from happening, always use the
provided dust caps whenever optical connectors are exposed to air. It is also a good
idea to gently clean the tip of an optical connector with a lint-free cloth moistened
with alcohol whenever dust is suspected.
The status of the VIDEO and AUDIO indicator LEDs should provide the rst clue as
to the origin of an operational failure. If these are off, it usually means that the ber is
broken or has too much attenuation. Next, be certain that the input and output signal
connections are correct.
If, after reviewing the above possibilities, the system is still not operating, please
contact the Black Box Tech Support for further assistance
The RGBHV with Stereo Audio ber optic transmission system is designed to operate
with most multimode (MM) and single mode (SM) optical bers.
Remember to check the attenuation and bandwidth of the ber optic cable. The
system will only operate properly if these specications fall within the range of the
system’s loss budget.
Optical Fiber:Troubleshooting:Maintenance:
The only maintenance of the AC1020A system that can be provided by the user is to
ascertain that the optical connectors are free of dust or dirt that could interfere with light
transmission and that electrical connections are secure and accurate. DANGER! Always
disconnect the transmitter power before removing the optical ber from the unit! For
assistance with all other repairs, please contact Black Box technical support.