Blodgett warranty Model B36-HHH, Utility Information, Other Technical Information

MODEL B36-HHH

APPROVAL/STAMP

SHORT FORM SPECIFICATIONS

The item shall be a 36"-wide front-manifold sectional range with full width hot-top with three 32,000 BTU sections, a cast iron surface, and an operating surface temperature of up to 700°F. The item shall have a 7" front rail and a belly bar. The item shall have 6" adjustable legs [casters]. The item shall have a [5" 24" 36"] flue riser able to support 250 pounds. The exterior (except for the back) shall be constructed of 430 stainless steel #3 polish. If the item is at the end of a battery, the end side shall be solid (rather than have a coverplate over the end of the front manifold).

Model 36A: The item shall have a 45,000 BTU convection oven with standing pilot and a thermostat range of 150°F to 550°F (66°C to 288°C). The oven interior shall be porcelain, meas- ure 14" high x 26" wide x 24" deep, and have two racks with five-position side-rails with 2-1/4" between positions. The blower fan shall have two speeds and a 1/3 hp motor.

Model 36D: The item shall have a 45,000 BTU standard oven with standing pilot and a thermostat range of 150°F to 550°F (66°C to 288°C). The oven interior shall be porcelain, meas- ure 14" high x 26" wide x 26.5" deep, and have two racks with five-position side-rails with 2-1/4" between positions.

Model 36C: The item shall have a cabinet base with two side-by-side stainless steel doors.

	UTILITY INFORMATION				GAS: Each unit has a 1-1/4" front gas manifold that couples to the adjacent sectional unit(s), and can be
					ordered with a 1" rear gas connection with a male NPT connector. Minimum supply pressure is 7" W.C. for
	GAS (BTU/hr)		ELECTRICITY (amp)
MODEL					natural gas, 11" W.C. for propane. An external pressure regulator and shut off valve must be provided. If
	Natural Gas	Propane	120V	208/240V
					using a flexible-hose gas connection, the I.D. of the hose must not be smaller than the connector on the unit
					and must comply with ANSI Z21.69. Provide an adequate means of restraint to prevent undue strain on the
B36A-HHH	141,000	126,000	4.8	2.6
					gas connection.
B36D-HHH	141,000	126,000	1.0	1.0	ELECTRICITY: Both standard-oven and convection-oven models require electric power (50Hz or 60Hz single-
					phase AC). 120V models have a 7-foot (2134 mm) power cord with a grounded plug. 208/240V models
B36C-HHH	96,000	84,000	-	-
					have a terminal block for connection to a single-phase 208/240V source.
B36N-HHH	96,000	84,000	-	-	FLUE EXHAUST: Installation under a vented hood is recommended.

OTHER TECHNICAL INFORMATION

Exterior surfaces are 430 stainless steel #3 polish, except the back is aluminized steel.

Each 12” section has a separate control knob located on the front panel. On oven models, a gas valve for the oven is located on the front panel above the oven. The oven control panel is located to the left of the oven door and includes an on-off switch, indicator light, thermostat knob, and (on convection ovens) a speed selector switch for the blower motor. The fan motor for convection ovens is 1/3 hp, 2-speed, 1725/1140 rpm, with overload protection. Check local codes for fire and sanitary regulations.

NOTE: The company reserves the right to make substitutions of components without prior notice

BLODGETT

www.blodgett.com

1100 Old Honeycutt Road Fuquay-Varina, NC 27526 USA • Phone: (877) 255-3976 • Fax: (866) 644-1354

Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY P/N BR00029 Rev D (6/08)