page no.
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Operating Instructions
NOTE: Heater functions best WITHOUT an extension cord.
If an extension cord is necessary:
• Use a UL approved, 3 prong plug (grounded) cord shall be no. 16 AWG minimum size |
and rated not less than 1500 watts. |
• Never connect two or more extension cords together. |
• Use the shortest extension cord possible. |
• Keep connections dry and off the ground. |
• Avoid draping the electric heater cord where children or animals could encounter it. |
Cleaning and Care (continued)
Cleaning Surfaces
1.Wipe surfaces clean with a solution of water and mild dishwashing detergent or baking soda.
2.Wipe clean with damp cloth.
Note: While cleaning your unit, be sure to keep the area around the heating element dry at all times. Do not submerge the heating element. If the heating element is submerged in water, do NOT use it. It must be replaced.
Before Turning “ON”
1.Make sure all labels, packaging and protective films have been removed from the heater.
2.Heater should be thoroughly inspected before each use, and by a qualified service person at least annually.
Turning “ON” | Illustration 1 |
Maintenance
To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis:
1.Keep exterior surfaces clean.
2.Air flow must be unobstructed. Keep circulating air passages around the heating element clean.
1.Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 1)
2.Push the power button. (Illustration 2)
Note: The red LED light will glow while the heater is on.
Note: When restarting the heating element will start up slowly before getting to full power.
While Heater is “ON”
If heater tips over, the heater will automatically turn “OFF”.
If heater tips over:
1.IMMEDIATLEY unplug power cord from the wall outlet.
2.Carefully turn the heater upright.
Connecting the power cord to a
dry GFI 3 plug outlet.
Illustration 2
Replacing the Fuse
1.Push the power button. (Illustration 2)
2.Unplug the power cord from the wall outlet.
3.Using a screwdriver, remove the fuse cover. (Illustration 4)
4.Carefully remove the old fuse, and replace with the new fuse. (Illustration 5)
Note: ONLY replace the old fuse with a 250V 15A fuse.
5.Reattach the fuse cover. Note: Do not over tighten
6.Follow the Turning “ON” instructions or the Storage Instructions.
Remove fuse cover
Illustration 5
Remove old fuse
CAUTION: Dome, pole and shroud cover may be hot. Use heat resistant gloves to set heater upright.
3.Inspect heater to ensure no damage. If no damage continue to next step.
If there is damage call a qualified technician to inspect and make any necessary repairs.
Do NOT use the heater if there is any sign of damage. A qualified technician should inspect and make any nescessary repairs before the heater is used again.
Power button
Storage
Between Uses and During Periods of Extended Inactivity or When Transporting:
1. | Push the power button. (Illustration 2) |
2. | Unplug the power cord from the wall outlet. |
3. | Store heater upright in an area sheltered from direct contact with inclement weather (such |
| as rain, sleet, hail, snow, dust and debris). |
4. | If desired, cover heater to protect exterior surfaces and to help prevent build up in air |
4.Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 1)
5.Push the power button. (Illustration 2)
Note: The red LED light will glow while the heater is on.
Note: When restarting the heating element will start up slowly before getting to full power.
Turning “OFF”
1.Push the power button. (Illustration 2)
2.Unplug the power cord from the wall outlet.
Cleaning and Care
Notices
1.Abrasive cleaners will damage this product.
2.Never use oven cleaner to clean any part of heater.
3.Do not clean any heater part in a self cleaning oven. The extreme heat will damage the finish.
4.Inspect heater before each use.
5.Have heater inspected annually and repairs should be made by a qualified service person.
6.Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.
7.Do not paint engine, engine panels or dome.
8.This heater should be thoroughly cleaned on a regular basis.
9.After a period of storage and/or non use, inspect for any abrasion, wear or cuts to the power cord.
passages. |
Wait until heater is cool before covering.