page no.
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Note: Always lock lid before folding legs.
Operating Instructions
This grill is designed to operate with a one pound
DO NOT ATTEMPT TO REFILL ANY ONE POUND (16.4 oz. or 14.1 oz.) PROPANE GAS TANKS!
Figure 1a | Figure 1b |
1. Make sure the regulator/control valve is in the “LOCK OFF” position. (Figure 1a)
2. Lubricate the threads of the regulator valve with |
| LOCK |
| |
| OFF | OFF | ||
petroleum jelly, insert the gas tank into the regulator | HIGH | PUSH |
| LOW |
TURN ON | ||||
|
| TO |
|
|
valve and |
| MED |
| |
3. Test for leaks |
|
| ||
|
|
|
| |
Note: Always open legs completely and are secured in place before lighting.
Burner Connection
1.Make sure the control valve is securely fastened to the burner. (Figure 2)
If your unit was assembled for you, visually check the connection between the burner and control valve.
WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property.
2.If the burner pipe does not rest flush to the control valve, please contact 1.800.762.1142 for assistance.
Regulator / 1# LP Gas Tank Connection
Figure 2
Figure 3
| LOCK |
| |
| OFF | OFF | |
HIGH | PUSH |
| LOW |
TURN ON | |||
| TO |
|
|
1. Make
liquid dishwashing soap with three parts water. | MED |
|
2.Make sure control knob is “OFF”. (Figure 3)
3.Spoon several drops of solution, or use squirt bottle, at the LP gas tank to regulator connection. (Figure 4)
4.Inspect the solution at the connection, looking for bubbles.
If NO bubbles appear, the connections are secure.
If bubbles appear, you have a leak.
a.Loosen and retighten this connection, making sure the connection is secure.
Figure 4
X
X
b. Retest with solution.
If you continue to see bubbles after several attempts, disconnect propane source and contact 1.800.762.1142 for assistance.
1.Make sure all labels, packaging and protective films have been removed from the grill.
2.Remove manufacturing oils before cooking on this grill for the first time, by operating the grill for at least 15 minutes on “HIGH” with the lid closed. This will “heat clean” the internal parts and dissipate odors.
Lighting1.Make sure all labels, packaging and protective films have been removed from the grill.
2.Open lid. Attempting to light the burner with the lid closed may cause an explosion!
3.Make sure there are no obstructions of airflow to the gas unit. Spiders and insects can nest within and clog
the burner / venturi tube at the orifice.
A clogged burner tube can lead to a fire beneath the appliance.
4.Control knob must be in the “LOCK OFF” position. (Figure 4)
5.Turn the control knob to “HIGH”
6.Press the Igniter button repeatedly to light burner.
7.If ignition does not occur in 5 seconds, turn burner control knob OFF, wait 5 minutes and repeat lighting procedure.
8.If igniter does not light burner, use a lit match secured with the lighting rod provided to light burners manually. Access the burner through the hole in bottom bowl as indicated. (Figure 5 and 6)
9.Turn the grill to “LOW”, and position the lit match near side of the burner.
Important: Always use the lighting rod provided when lighting burners with a match.
Figure 5
Match
Figure 6
| Figure 7 |
Flame | 1/2" |
12.7 mm |
1/4"
6.4mm
0"
0mm