Blue Sea Systems 120 V Ac ELCI MAin Panels instruction

Marine Electrical Products

120V AC ELCI Main panels

PN 8100 / PN 8101 / PN 8102

Specifications

Material:	0.125" 5052-H32 Aluminum Alloy
Primary Finish:	Chemical Treatment per Mil Spec C-5541C
Final Panel Finish:	Graphite color 2 part textured Polyurethane
Circuit Breakers:	30A Main with 30mA trip ELCI, and (if equipped),
	15A single pole AC/DC Circuit Breaker
Amperage Rating:	Panel is rated for 30 amps service.
Voltage Rating:	Panels are rated for 120 volts AC and are so marked
	in order to comply with ABYC standards
	PN	Inches	Millimeters
Overall Dimensions: 8101/8102		5-1/4 × 7-1/2	133.4 × 190.5
	8100	5-1/4 × 3-3/4	133.4 × 95.3

Applicable Standards

•American Boat and Yacht Council (ABYC) Standards and recommended Practices for Small Crafts sections: E-11, AC and DC Electrical Systems on Boats.

•United States Coast Guard Code of Federal Regulations 33, Part 183, Subpart I, Electrical Systems on Boats.

GUARANTEE: Blue Sea Systems stands behind its products for as long as you own them. Find detailed information at www.bluesea.com/about. For customer service, call 800-222-7617.

Blue Sea Systems Inc.	Phone (360)	738-8230
425 Sequoia Drive	Fax (360)	734-4195
Bellingham, WA 98226 USA	www.bluesea.com
	980006510 Rev. 002

Installation

1.Disconnect all AC and DC power

Disconnect all AC power originating on or off the vessel. This includes inverters, generators, shore power attachments and any other device capable of supplying AC power to the ship’s circuits.

Disconnect the main positive DC cable from all batteries to eliminate the possibility of a short circuit and to disable the inverter while installing the distribution panel.

2.Select mounting location and cut opening

This panel is to serve as your main shore power disconnect circuit breaker. Select a location which is not more than 10 feet from the shore power inlet or the electrical attachment point of a permanently installed shore power cord as measured along the conductors of the feed wires. If it is more than 10 feet additional fuses or circuit breakers must be installed within 10 feet of the shore power inlet.

Select a mounting location which is protected from water on the panel front and back and is not in an area where flammable vapors from propane, gasoline or lead acid batteries accumulate. The circuit breakers used in this marine electrical panel are not ignition protected and may ignite such vapors.

Using the panel template provided, make a cut out in the mounting surface where the distribution panel is to be mounted. Do not yet fasten the panel to the mounting surface.

3.Install branch circuit wires

Determine the proper wire size for each branch circuit using the wire sizing chart . Verify that the standard 15 amp circuit breakers installed in the panel are correct for each branch circuit. Remove and replace any that are incorrectly sized. The circuit breaker must have a rating less than the allowable amperage of the wire, yet greater than the circuit’s continuous current.

WARNING

It is not possible within the scope of these instructions to fully acquaint the installer with all the knowledge of electrical systems that may be necessary to correctly install this product. If the installer is not knowledgeable in electrical systems we strongly recommend that an electrical professional be retained to make the installation.

If either the panel front or back is to be exposed to water it must be protected with a waterproof shield.

The panels must not be installed in explosive environments such as gasoline engine rooms or battery compartments as the circuit breakers are not ignition proof.

The vessel’s shore power cord must be disconnected form shoreside power before installing this electrical panel.

If an inverter is installed on the vessel its power leads must be disconnected at the battery before the panel installation. Be aware that many inverters have a “sleep mode” in which their voltage potential may not be detectable with measuring equipment.

If an AC Generator is installed aboard it must be stopped and rendered inoperable before the panel is installed.

Verify that no other AC source is connected to the vessel’s wiring before the panel is installed.

Connect each branch circuit hot (black) to the appropriate load terminal. Connect each branch circuit neutral (white) to one of the screws on the neutral bus. Connect each branch safety ground wire (green) to one of the screws of the safety ground bus.

Do not confuse the neutral current carrying wires (sometimes called ground) with the green normally non-current carrying wires (sometimes called grounding). These two wires must be connected only at the source of power, nowhere else.

Wire sizing chart

Use the wire sizing chart below to determine the minimum branch circuit wire sizes.

ABYC E-11 Table VI-B 105˚ C ( 221˚ F) Wire


17.5	11.9
24.5	20.8

31.5	26.8
42.0	35.7

56	47.6
84	71.4

112	95.2
126	107.1

Note: This chart assumes wire with 105° C (221° F) insulation rating and no more than 3 conductors are bundled.

Not suitable for sizing flexible shore power cords.

Blue Sea Systems recommends that the feeder wires from the power inlet to the panel should be 10 AWG for 30A systems and 6 AWG for 50A systems.

120 V Ac ELCI MAin Panels specifications

Blue Sea Systems is renowned for its innovative electrical solutions, and their 120 V AC ELCI (Equipment Leakage Circuit Interrupter) Main Panels exemplify this commitment to safety, reliability, and performance in marine applications. These panels incorporate advanced technologies designed to protect both the vessel and its occupants from electrical hazards, making them an essential component for any boat or yacht.

One of the standout features of the Blue Sea Systems ELCI Main Panels is their ability to detect ground faults in electrical systems. The ELCI technology continuously monitors the electrical circuit for leakage current, automatically shutting off power in the event of a fault. This critical safety feature helps prevent electric shock incidents and reduces the risk of electrical fires on board.

The panels are designed with user-friendly interfaces, featuring clear indicators and robust construction that provides both durability and ease of operation. With a comprehensive DC and AC circuit distribution, the panels allow for organized wiring and simplified troubleshooting. Their space-efficient designs ensure they can be integrated conveniently into various vessel layouts, accommodating different sizes and setups.

Another hallmark of Blue Sea Systems products is their dedication to quality and compliance with marine industry standards. The ELCI Main Panels are built to meet stringent guidelines, ensuring they function reliably in the demanding marine environment, characterized by humidity, vibration, and temperature fluctuations. Their construction includes corrosion-resistant materials and is rigorously tested to withstand the challenges of life at sea.

The panels also offer versatile installation options, including the ability to accommodate multiple AC circuits with ease, making it simpler for users to customize their electrical systems. With options for both GFCI and non-GFCI circuit configurations, these panels cater to a wide range of electrical needs aboard vessels.

In summary, Blue Sea Systems' 120 V AC ELCI Main Panels integrate cutting-edge safety technology, user-friendly design, and robust construction to provide a superior electrical solution for marine environments. Their focus on safety and reliability makes them a top choice for boat manufacturers and marine electricians, enhancing the overall boating experience while ensuring the well-being of all onboard.

Blue Sea Systems 120 V Ac ELCI MAin Panels dimensions Specifications, Applicable Standards

Models: 120 V Ac ELCI MAin Panels