Installation

1.Disconnect all AC and DC power

Before starting, disconnect the main positive cable from all batteries to eliminate the possibility of a short circuit while installing the distribution panel. Also disconnect the AC shore power cord from the boat to eliminate the possibility of electrocution from AC wiring in the proximity of the DC distribution panel.

2.Select mounting location and cut opening

Select a mounting location which is not in an area where flammable vapors from propane, gasoline or lead acid batteries accumulate. This panel is not ignition protected and may ignite such vapors.

Using the panel template provided, make a cut out in the mounting surface where the distribution panel is to be mounted. Do not yet fasten the panel to the mounting surface.

3.Select positive feed wire

Determine the positive feed (red) wire size by calculating the total amperage of the circuits that will be routed through the panel. Blue Sea Systems’ water resistant electrical panels are rated at 45 amp total capacity. The positive feed wire must be sized for 3% voltage drop at the 45 amp panel rating or the maximum amperage that will be routed through the panel in any particular installation, whichever is less. It is recommended that the positive feed wire be sized for the full panel capacity, which, in most cases, will require at least 8 AWG wire, assuming a 10 foot wire run between the panel and the batteries in 12 volt systems. Refer to the Wire Sizing Chart for other situations. Remember that the length of the circuit is the total of the positive wire from the power source and the negative wire back to the DC Negative Bus. Be certain that there is a fuse or circuit breaker of the correct size protecting the positive feed wire.

4.Install LED negative feed wire

Use a 16 AWG wire to connect the LED negative feed (yellow) wire to the DC Negative Bus.

Wiring Diagram

DC Water Resistant Power Distribution Panel

5.Install branch circuit wires

Determine the proper wire size for each branch circuit using the guidelines in step 3. Verify that the standard 15 amp fuses installed in the panel are appropriate for each branch circuit. Remove and replace if necessary. Connect the positive (red) branch circuit wires to the load terminals of each switch. Connect each negative (black) branch circuit wire to a DC Negative Bus such as Blue Sea Systems’ MiniBus PN 2304.

6.Apply branch circuit labels

For each branch circuit, select a label from the 30 basic labels provided, and apply it to the recessed area on the front of the panel. If the appropriate labels are not found, the Extended Label Set of 120 labels may be ordered from your marine supplier (PN 8039). Individual labels are also available from Blue Sea Systems, and may be ordered using the provided Label Order Form.

7.Mount Panel with water resistant gasket

A gasket has been included for sealing the panel against the mounting surface. The gasket will easily stretch around the panel when applied from the front. Place the gasket between the panel and the mounting surface. Make sure all surfaces are clean and free from debris. Using the panel mounting screws supplied with the panel, screw down the panel to the mounting surface.

8.Testing

Reconnect the main positive cable to the battery terminals and turn the main switch on to supply power to the panel. Turn on all branch circuits and test the voltage at the panel. Compare this voltage to the battery terminal voltage to determine that the voltage drop is within 3%. With all branch circuits still on, test the voltage at one device on each circuit to determine that there is a 3% or 10% drop as is appropriate.

Note

This Blue Sea Systems electrical distribution panel is furnished with 15 amp AGC (fast acting) glass fuses. This rating was selected to minimize the need for removing the fuse and reinstalling different size fuses. 15 amp fuses will satisfy the vast majority of marine circuit protection situations.

Applicable Standards

•American Boat and Yacht Council (ABYC) Standards and Recommended Practices for Small Craft sections: E-1, E-3, E-9.

•United States Coast Guard 33 CFR Sub Part 1, Electrical Systems.

Wiring Diagram

DC Water Resistant Power Distribution Panel

PN 8053

PN 8054

Page 1 Page 2
Page 2
Image 2
Blue Sea Systems 8053 specifications Installation
Page 1 Page 2

8053 specifications

The Blue Sea Systems 8053 is a robust and reliable battery management solution designed to enhance the boating experience. This product stands out in the marine electronics market due to its comprehensive features and advanced technology.

One of the main features of the Blue Sea Systems 8053 is its Dual Battery System, which allows users to manage two separate batteries simultaneously. This capability ensures that critical systems on board, such as navigation equipment and lights, remain powered even when one battery is depleted. The device is designed to prevent over-discharging, which can extend the lifespan of the batteries and provide peace of mind to boaters.

Another significant characteristic of the 8053 is its automatic charging functionality. This feature integrates seamlessly with the boat's charging system, ensuring that both batteries are charged optimally when the engine is running or when a shore power connection is available. The incorporation of a sophisticated voltage sensing system guarantees that batteries are charged based on their specific needs, enhancing overall efficiency.

The 8053 also includes an integrated LED indicator system, which provides real-time visual feedback on battery status and charging conditions. This user-friendly aspect eliminates the need for constant manual checks and helps boaters quickly assess the health of their batteries. The clear, color-coded indicators show battery levels and operational status, allowing for easy troubleshooting if issues arise.

Furthermore, the Blue Sea Systems 8053 is built with high-quality marine-grade materials that ensure durability and longevity in harsh marine environments. Its design features sealed components to protect against moisture and corrosion, making it ideal for use in both freshwater and saltwater settings.

Safety is paramount, and the 8053 is engineered with built-in protection mechanisms against common electrical issues, such as overloads and shorts. These safety features help mitigate risks while ensuring reliable operation.

Overall, the Blue Sea Systems 8053 is a comprehensive, user-friendly battery management system that enhances the reliability and efficiency of a vessel's electrical system. With its advanced charging technology and robust safety features, it is an excellent choice for boaters looking to optimize their power management needs on the water.
Top Page Image Contents