Marine Electrical Products
Analog AC Voltmeter
0-150 Volts PN 8244 / PN 9353
Meter Specifications
Input Voltage: | PN | Voltage |
|
8244/9353 | |||
| 8245/9354 | ||
Amperage Draw: | 1 Milliampere |
| |
Display: | Analog scale |
| |
Accuracy: | 3% of scale range |
| |
Face Width: | PN | Inches | Millimeters |
8244/8245 | 2 | 50.80 | |
| 9353/9354 | 66.70 | |
Mounting Hole: | 8244/8245 | 38.10 | |
| 9353/9354 | 47.60 |
Guarantee
Any Blue Sea Systems product with which a customer is not satisfied may be returned for a refund or replacement at any time.
Installation
Warning
It is not possible within the scope of these instructions to fully acquaint the installer with all the knowledge of electrical systems that may be necessary to correctly install this product. If the installer is not knowledgeable in electrical systems we recommend that an electrical professional be retained to make the installation.
1. Disconnect all AC and DC power
Disconnect all AC power originating on or off the vessel. This includes inverters, generators, shore power attachments and any other device capable of supplying AC power to the ship’s circuits. Disconnect the main positive DC cable from all batteries to eliminate the possibility of a short circuit and to disable the inverter while installing the meter.
Blue Sea Systems Inc.
425 Sequoia Drive Bellingham, WA 98226 USA
Phone (360)
www.bluesea.com
9332 Rev. 003
Marine Electrical Products
Analog AC Voltmeter
Meter Specifications
Input Voltage: | PN | Voltage |
|
8244/9353 | |||
| 8245/9354 | ||
Amperage Draw: | 1 Milliampere |
| |
Display: | Analog scale |
| |
Accuracy: | 3% of scale range |
| |
Face Width: | PN | Inches | Millimeters |
8244/8245 | 2 | 50.80 | |
| 9353/9354 | 66.70 | |
Mounting Hole: | 8244/8245 | 38.10 | |
| 9353/9354 | 47.60 |
Guarantee
Any Blue Sea Systems product with which a customer is not satisfied may be returned for a refund or replacement at any time.
Installation
Warning
It is not possible within the scope of these instructions to fully acquaint the installer with all the knowledge of electrical systems that may be necessary to correctly install this product. If the installer is not knowledgeable in electrical systems we recommend that an electrical professional be retained to make the installation.
1. Disconnect all AC and DC power
Disconnect all AC power originating on or off the vessel. This includes inverters, generators, shore power attachments and any other device capable of supplying AC power to the ship’s circuits. Disconnect the main positive DC cable from all batteries to eliminate the possibility of a short circuit and to disable the inverter while installing the meter.
Blue Sea Systems Inc.
425 Sequoia Drive Bellingham, WA 98226 USA
Phone (360)
www.bluesea.com
9332 Rev. 003
( Installation (continued)
2.Select mounting location and cut opening
Select a mounting location which is protected from water on the meter front and back and is not in an area where flammable vapors from propane, gasoline or lead acid batteries accumulate. The meter is not ignition protected and may ignite such vapors. There are two mounting methods for the meters, surface mount or panel mount.
Surface Mount: Drill five clearance holes as shown below. The part number of the meter will determine the size and location of the clearance holes. Use the nuts and washers supplied in the accessory package to secure the four mounting studs to the mounting surface. This method will work on mounting surfaces up to 5/8” thick.
PN 8244 | / PN 8245 | PN 9353 / PN 9354 |
Micro | Meters | Standard Meters |
Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use PN 8013 to mount a single meter or PN 8014 to mount two meters.
( Installation (continued)
2.Select mounting location and cut opening
Select a mounting location which is protected from water on the meter front and back and is not in an area where flammable vapors from propane, gasoline or lead acid batteries accumulate. The meter is not ignition protected and may ignite such vapors. There are two mounting methods for the meters, surface mount or panel mount.
Surface Mount: Drill five clearance holes as shown below. The part number of the meter will determine the size and location of the clearance holes. Use the nuts and washers supplied in the accessory package to secure the four mounting studs to the mounting surface. This method will work on mounting surfaces up to 5/8” thick.
PN 8244 | / PN 8245 | PN 9353 / PN 9354 |
Micro | Meters | Standard Meters |
Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use PN 8013 to mount a single meter or PN 8014 to mount two meters.