Fig. 21
Stroller with handlebar folded.
Fig. 16 Place straps over shoulders
and secure to buckle.
10. SEAT SAFETY
HARNESS: Set parking brake before
placing child in stroller. To secure your child in the
seat, put one shoulder strap over each shoulder
and snap the male buckle into the female receiver on
the crotch strap (Fig. 16). Adjust shoulder straps to
be snug and secure (Fig.
17). Connect and adjust
the sternum strap (red), see Fig. 18.
WARNING: Never place passengers in the stroller without securing them in the harness. Unrestrained passengers can affect the control
Crotch
Strap
Buckle
Shoulder
Strap
9. SUN CANOPY: The stroller features a two position canopy. To fully open the canopy, rotate the assembly forward until the fabric is taut. The rear canopy flap should be freed from the Velcro to give additional sun protection. To reduce the size of the sun canopy, pull the canopy toward the handlebar. The additional fabric can be gathered by pulling the canopy
drawstring (Fig. 1) and
securing the cord lock.
To set the parking brake, press the brake bar down into the locked position (Fig. 14) with your foot on the red foot pedal – making sure the locking pin fully engages the locking disk. To ensure the brake is set properly, attempt to roll the stroller fore and aft after setting the brake. If the stroller will not roll, the brake is set properly. To release the parking brake, lift up on the red foot pedal with your foot until the brake bar springs up into the fully unlocked position (Fig. 15).
Parking Brake - Unlocked position.
Fig. 15
Brake Bar
(Unlocked Position)
Parking Brake - Locked position.
Fig. 14
8. PARKING
BRAKE: The brake is a parking brake, it prevents the stroller from moving while loading and
unloading. The parking brake is not designed as a stopping brake. Do not use the brake to slow or stop the stroller. The brake
is intended to park the stroller on flat surfaces, not on inclines. Never leave your child in
the stroller unattended with or without the parking brake set!
Brake Bar
(Locked Position)
Red Foot Pedal
Locking
Disk
Locking
Pin
(Engaged)
Fine tune tracking of stroller is accomplished by using the tracking adjustment knob shown in Fig. 13. If your stroller pulls to the left, turn the knob counter-
clockwise 1/2 turn. If your stroller pulls
to the right, turn the
knob clockwise 1/2 turn. Repeat Roll
test and adjustment until the stroller rolls straight.
Seat in fully reclined position.
Fig.20
Fig. 19
Fig. 18
Fig. 17
Seat in fully upright position.
Reclining Strap
Loops
Connect sternum strap.
Securely adjust shoulder straps.
Sternum
Strap
below until tracking is satisfactory. Fig. 12 illustrates how to interpret the results.
Reference convention: Left and right are described as viewed from
the operator’s frame of reference (behind the stroller). Example: The swivel lockout knob is on the left side of the stroller.
Seat Reclining
Ladder Lock
Buckles
BOB REVOLUTION OWNER’S MANUAL
of the stroller.
Passenger weight limit - 70 lbs (32 kg)
Passenger height limit - 44 in (112 cm)
11. RECLINING SEAT:
Set parking brake before making any seat adjustments. To recline the seat, rotate the ladder lock buckles (Fig. 19) forward thus releasing the reclining straps. To raise the seat, pull the reclining strap loops until you obtain the desired position. The seat back can be adjusted to recline anywhere between the fully upright position and the fully reclined position (Fig. 19 & 20).
12. SHOCK ABSORBERS:
The suspension system features two shock positions to provide a
comfortable ride for kids of different weights. The two positions are shown in Fig. 2. Position 1 is intended for
occupants up to 40 lbs. (18 kg), while position 2 is intended for occupants from 40 to 70 lbs. (18
to 32 kg) total. The stroller features a metal shock bracket
with a sliding track and spring loaded shock pin that
automatically locks in place when
it aligns with either of the two shock positions. Shock position adjustments should be made with
the stroller unloaded. The shocks
will lock into position 1 when unfolding the stroller. To use the
stiffer shock position, move the shock from position 1 to position
2 by depressing the shock release button (Fig. 2) with one hand, and with the other hand, lift slightly and pull the shock backward.
When the shock pin is properly
aligned in position 2, the pin will
“snap” into place. Repeat this process for the second shock. To move the shock from position 2 to position 1, reverse the above process for both shocks.
13. FOLDING:
Remove child from stroller. Remove the contents of the Low Boy cargo pouch, seat back and seat pockets. The shock absorbers must be in position 1 (Fig. 2) before folding. Press both the right and left handlebar release levers (Fig. 3), and fold the handlebar forward as shown in Fig. 21. Locate the
frame release handle
underneath the seat (Fig. 22) and pull upwards
sharply. This will allow the
lower frame to fold
together, as shown in Fig. 23. The folded stroller can be made even more
compact by removing the
front and rear wheels. The front wheel is removed by
opening the front wheel quick release and removing the wheel
