TRAVEL bag INSTRUCTIONS
(800)
Fax: (208)
Congratulations on your purchase of the BOB Travel Bag. It is designed to contain and protect your single seat BOB Sport Utility, Revolution or Stroller Strides stroller during transport. The Travel Bag may be rolled and guided by the end handle or carried via shoulder strap and/or side handle. The Travel Bag will need to be assembled prior to use.
Before attempting to assemble or use your new Travel Bag, read and understand these instructions to ensure proper assembly and operation. If you are unclear on any point, contact your dealer or BOB before use.
WARNINGS
. This product is designed exclusively for use with BOB single Sport Utility, Revolution or Stroller Strides strollers. It is not intended for use with any other strollers or products.
. When not in use, keep out of reach of children.
. Maximum Weight Capacity 30lb (13.6Kg) Do not overload.
. Never leave child unattended.
. The Travel Bag is designed to reduce the possibility of damage to your stroller during transportation but does not eliminate it completely.
. We recommend inspecting your Stroller and Travel Bag before and after each transport journey to ensure functionality and safety.
Assembly Instructions:
A1. Remove bag from packaging. Place bag flat on ground or table with wheels down. Open Travel Bag top cover zipper and locate components. Fig. A identifies the anatomy and components of the Travel Bag.
A2. Unfasten the Velcro of the five Fabric Flaps along inboard sides of travel bag. Temporarily place top of each over side and out of the way as shown in Fig. A.
A3. Locate wall support panel, (black plastic sheet) unroll and note orientation of notch at each end.
A4. Orient wall support panel with notches toward top cover (up) and feed each end into each respective pocket along inside corners of Travel Bag as shown in Fig B. Push ends of wall support panel fully into each pocket until notch is aligned with pocket seam.
A5. Align and fasten Velcro of fabric flaps straight and secure around wall support panel. You may find it helpful to bend the support panel top edge slightly inboard while the Velcro of each fabric flap is secured.
|
|
|
Wall Support Panel (rolled up) |
| Zippered Top Cover |
|
|
|
Front
Wheel
Center Strap
& BuckleFront QR
Pocket Seam
Notch
Insert Notch fully up to Seam
Fig. B: Panel ends into corner pockets (right side shown).
Fig. C: Fork Dropout Protector shown properly attached.
Center Strap open w/ends outboard
Top
Cover
Open
Fig. 1: Travel Bag fully assembled and prepared for stroller.
A6. Locate fork dropout protector and confirm it is attached securely to end of small red webbing as shown in Fig. C. The fork dropout protector can be replaced easily if lost or damaged with most other common fork dropout protector(s) used on strollers and bicycles for shipping, available through your bicycle or stroller dealer.
Use Instructions:
U1. Prepare Travel Bag: Zip Travel Bag zipper completely open and fold top cover over, exposing pockets for Front Wheel and Front Wheel Quick Release (QR). Locate center strap and unfasten side release buckle. Place center strap ends outboard of Travel Bag as shown in Fig. 1.
U2. Prepare stroller to place in Travel Bag. Remove contents from stroller (occupant and all contents of Low Boy luggage pouch). Remove stroller rear wheels. Close rear wheel QR’s. (See Rear Wheel section of your stroller’s owner’s manual).
U3. Remove Front Wheel from stroller (See Front Wheel section of your stroller’s owner’s manual). Remove Front QR from Front Wheel. Reassemble Front QR components in proper orientation as shown in Fig. 2, and place inside the gray pocket located inside top cover of Travel Bag. Locate black plastic axle protectors at ends of red straps inside large front wheel pocket. Push hollow end of each plastic axle protector fully over each end of Front Wheel axle as shown in Fig. 3. Place Front Wheel into pocket inside top cover and fasten Velcro closures.
| Fork Protector |
|
|
|
|
|
|
|
|
| |
|
| Fabric Flaps | |||
| & Strap |
| |||
|
|
|
| (open) | |
|
|
|
|
| |
|
|
|
|
|
|
Shoulder
Handles Strap
Cam Housing
Conical
Springs
Rod
Adjusting Nut
QR
Lever
U4. Place rear wheels inside Travel Bag with stub axles facing up. Position stroller wheels along center line as far back towards base of bag as possible, leaving extra space for fork protector, as shown in Fig. 4.
U5. For Sport Utility Stroller (fixed wheel) models, close
Fig. A: Anatomy of the BOB Travel Bag.
Fig. 2: Front QR anatomy shown properly assembled.
Caliper Brake Quick Release Lever after removing wheel, as stroller will fold more
OMA17A | P1 |