Bosch Appliances specifications R-U,Z, RF835E Lens inside view

3.7	Set the PIR Sensitivity.			3.8 Uncover the Look Down Lens.		3.9	Mount the Detector Base.
		For pet applications,						Corner mount
	PIR	set jumper to STD.
	Sensitivity
	Selection Pins						Breakaway
							Thinwall
		INT					to activate	Surface
	INT		INT		STD		Wall
							Tamper	mount
		STD			INT
	STD		STD		- 10		Switch
					- 6
					MAX
	MAX		INT	Peel away	MW
	MIN				MIN
	MW		STD	the mask				Corner mount
				In non-pet applications only, if
						Note: The Wall Tamper cannot be used in
Note: The INT setting is more sensitive than				look-down is desired, peel away
				the look-down mask. Do not			corner mount installations or when
	the STD setting.			remove the clear plastic lens.			using the swivel bracket.

3.10 Remove the battery		ID Label	During the warm-up period, the tricolor LED will flash red until the unit has stabilized
tab, install the wall			(approximately 5 minutes). When the LED stops flashing, the detector is ready to be
tamper spring,			walk tested.	LED Condition	Cause
replace the	Pull battery		If the Wall Tamper is desired, gently	Steady Red	Unit Alarm
cover and	tab out from
base.	between the		press the Spring onto the tapered	Steady Yellow	Microwave Activation (Walk Test)
	battery and		shaft. Do not force it down onto the	Steady Green	PIR Activation (Walk Test)
	its contact.		shaft. As you place the unit onto its
				Flashing Red	Warm-Up Period After Power-Up
			base, be sure the spring extends
			through the knockout to the wall.	Flashing Red (four-	Microwave or PIR Failure Replace Unit
				pulsed sequence)

3.11Walk test the detector. Perform this test at the time of installation and monthly thereafter. To ensure continual daily operation, the end user should be instructed to walk through the far end of the coverage pattern. This ensures an alarm output prior to arming the system.

Pattern Testing in Walk Test Mode

Watch for the yellow LED to indicate the edges of the microwave pattern. Adjust as necessary.

Removing and replacing the cover will start a 90 second Walk Test Mode. During this Test Mode, any activity in the sensor’s coverage pattern will cause a transmitted alarm and LED activation. Each alarm will also extend the Test Mode for an additional 90 seconds.

Green = PIR detect

Yellow = MW detect

Red =

Alarm

Set the adjustment as low as possible for proper catch performance

INT

STD

MIN MAX

MIN MAX

4.0Coverage Patterns

Note: The protective zone is the area where the PIR and Microwave technologies overlap.

	Meters
0		1.6			3.2		4.8	6.4	8	9.6		11.2
10														3
		SIDE VIEW
Remove											B-L		-5°
			LZ	W-X		R-U,Z		N-Q
masking for
Look-Down 0														0
Zone
0		5			10		15	20	25	30		35

Feet

	Meters
0		1.6		3.2		4.8		6.4		8	9.6		11.2
20														6
		TOP	VIEW				B			C
15											D
						N
10											E			3
					R		O
5
				W	S							F
			LZ		Z							G
0														0
				X	T
5
							P					H
10					U	Q					I			3
15						L			K		J
20														6
0		5		10		15		20		25	30		35
Feet

Pattern Masking: The PIR coverage pattern may be masked.

B C D E F G H I J K L

N RW S O Z P T X U Q

RF835E Lens

(inside view)

NOTE: Masking only eliminates the PIR portion of the coverage and has no effect on the Microwave pattern.

5.0 Panel Programming

There is a two-part ID sticker located on the housing of the RF835E. You will need the number on this sticker to program the Detector into the control panel. See your panel's Programming Guide for programming information on wireless type devices.

ID Number

167770187

167770187

Countries of Intended Use: These products are intended for use in the following countries within the European Union and in countries outside the European Union:

•RF835E Austria, Belgium, Denmark, Finland, Greece, Luxembourg, Netherlands, Norway, Spain, and Sweden.

•RF835E-CUnited Kingdom, Ireland, and France.

© 2004 Bosch Security Systems	03/04
130 Perinton Parkway, Fairport, New York, USA 14450-9199	RF835E Installation Instructions
Customer Service: (800) 289-0096; Technical Support: (888) 886-6189	P/N: 48544D Page 2