OPERATING INSTRUCTIONS and parts explosions

CRT Models

Unpacking and Assembly

Your rototiller comes fully assembled except for a few parts. The fol- lowing instructions will help you unpack your tiller and assemble and adjust your tiller’s depth regulator lever, cable tension and handlebar height. You will need 2- 9/16” wrenches.

Unpack tiller

1.Open top of carton and remove handlebar assembly.

2.Find parts packet. Parts packet contains:

4- 3/8-16 x 3/4” hex head bolts 4- 3/8-16 locknuts

1- 5/16-18 x 3/4” hex head bolt 1- detent pin

1- five star knob

3.Cut open end of carton and remove machine by:

a.Removing lock pins on wheels.

b.Roll tiller from carton.

IMPORTANT

The right and left sides ofyour rototiller are determined from the operating position as you face the direction of forward travel.

Engine is shipped from factory without oil.You must add engine oil before starting engine.

!CAUTION

DO NOT TRY TO LIFT THE ROTOTILLER FROM THE CARTON.

DO NOT ADD ENGINE OIL INTO GEAR CASE DIP- STICK HOLE.

INSTALL BATTERY BOX (6065VE)

NOTE:The battery box assembly comes already mounted on the lower handlebar mount.

1.Remove and discard bolts and nuts that are holding the battery box assembly to the lower handlebar mount. Carefully set aside battery box so that wiring remains intact.

attach handlebar to tiller

1.Place handlebar stems on outside of lower handlebar mount and align lower holes.

2.Insert one 3/8-16 x 3/4” bolt for each side in lower holes at the desired handlebar height.

3.Start 3/8-16 nuts on each bolt.

4.Insert one 3/8-16 x 3/4” bolt for each side in upper holes.

5.Start 5/16” washers and 3/8-16 nuts on each bolt.

6.Place notches of battery box support over the four bolts between lower handlebar mount and nuts.

7.Tighten all 3/8-16 nuts.

8.Remove the battery box cover and plug the white plastic connec- tor from the battery into the mating white plastic connector in the battery box. Make sure the ignition key is removed from the ignition before connecting the wiring for the battery. Replace battery box cover.

Fill engine CRANKCASE

1.Add oil according to engine manual. Do not overfill. Use a clean, high quality detergent oil. Container must be marked A.P.I. Service SF - SJ. Use no special additives with recommended oils. Do not mix oil with gasoline. Oil level must be full. Check the oil level by removing oil fill plug. Oil level should be up to the bottom of the fill plug opening.

2.Always check oil level before starting engine. Refer to engine manual for capacity and type of oil to use.

3/8-16

lower handlebar

 

mount

 

nuts

3/8-16 x 3/4”

 

 

 

bolts

height

handlebar

adjustment

stem

holes

 

 

gear case

 

dipstick

 

gear case

 

dipstick hole

NO ENGINE OIL!

Page

800-345-6007

Page 6
Image 6
Briggs & Stratton R5055H 5.5 HP, 5155 6 HP, 5055 6 HP Unpacking and Assembly, Unpack tiller, Install Battery BOX 6065VE

R5055H 5.5 HP, 5055 6 HP, 5155 6 HP specifications

Briggs & Stratton has long been recognized as a leader in small engine manufacturing, known for durable and reliable power solutions. Among their impressive lineup, the Briggs & Stratton 5155 6 HP, 5055 6 HP, and R5055H 5.5 HP engines stand out due to their performance, efficiency, and innovative technologies. These engines are designed for a wide range of applications, from lawn mowers and generators to pressure washers and garden equipment.

The Briggs & Stratton 5155 6 HP engine is characterized by its robust design, ensuring longevity and consistent performance under demanding conditions. With a displacement of 205cc, this engine is equipped with a solid cast iron cylinder sleeve that enhances durability and reduces wear. The overhead valve (OHV) configuration allows for better airflow, which results in improved efficiency and better fuel economy. It also features a dual clean air cleaner system, providing superior filtration and extending the life of the engine.

The 5055 6 HP model shares many similarities with the 5155 but is tailored for different applications, providing a reliable power source with remarkable torque. Its 206cc displacement along with an overhead valve design ensures effective combustion and efficient fuel usage. The 5055 is equipped with a recoil start, making it user-friendly for quick and easy startup, while also including a heavy-duty steel base for improved stability during operation.

Meanwhile, the R5055H 5.5 HP engine is specially designed for high-performance demands. With a slightly lower horsepower of 5.5, it still offers excellent power output thanks to its strategic engineering. The R5055H features a compact design that allows it to fit into tighter spaces, making it ideal for lightweight equipment without compromising on performance. Like the other models, it includes an OHV design for efficient fuel consumption and reduced emissions.

All three models incorporate advanced technologies that enhance serviceability and performance. The Easy Clean fuel system minimizes maintenance while ensuring effective operation in various conditions. Their user-friendly designs and operation features provide ease of use, making them suitable for both professional landscapers and residential users alike. Additionally, Briggs & Stratton engines are known for their strong customer support and warranty options, providing peace of mind with each purchase.

In summary, the Briggs & Stratton 5155 6 HP, 5055 6 HP, and R5055H 5.5 HP engines highlight the company's commitment to quality and innovation. With impressive specifications, advanced technologies, and an emphasis on durability, these engines are excellent choices for anyone seeking dependable power solutions for various outdoor applications.