REGULAR MAINTENANCE
This unit has been designed to be as
Use only the replacement batteries listed below. The unit may not operate properly with other batteries. Never use rechargeable batteries since they may not provide a constant charge.
• Test it at least once a week. |
• Clean the CO Alarm at least once a month; gently vacuum the outside |
of the CO Alarm using your household vacuum’s soft brush attachment. |
A can of clean compressed air (sold at computer or office supply stores) |
may also be used. Follow manufacturer instructions for use. Test the CO |
Alarm. Never use water, cleaners or solvents since they may damage the |
unit. |
HOW CAN I PROTECT MY FAMILY FROM CO POISONING?
A CO Alarm is an excellent means of protection. It monitors the air and sounds a loud alarm before Carbon Monoxide levels become threatening for average, healthy adults.
A CO Alarm is not a substitute for proper maintenance of home appliances.
To help prevent CO problems and reduce the risk of CO poisoning:
• Clean chimneys and flues yearly. Keep them free of debris, leaves, and |
nests for proper air flow. Also, have a professional check for rust and |
corrosion, cracks, or separations. These conditions can prevent proper |
air movement and cause backdrafting. Never “cap” or cover a chimney |
in any way that would block air flow. |
• Test and maintain all |
REGULATORY INFORMATION FOR CO ALARMS, Continued
Standards: Underwriters Laboratories Inc. Single and Multiple Station carbon monoxide alarms UL2034.
According to Underwriters Laboratories Inc. UL2034, Section
USER’S MANUAL |
ONELINK® BATTERY OPERATED |
CARBON MONOXIDE ALARM |
Features: |
ONELINK® Enabled |
Voice with Programmable Location |
Two Latching Features |
INSTALLATION
WHERE TO INSTALL CO ALARMS
The National Fire Protection Association (NFPA) recommends that a CO Alarm should be centrally located outside of each separate sleeping area in the immediate vicinity of the bedrooms. For added protection, install additional CO Alarms in each separate bedroom, and on every level of your home.
If your bedroom hallway is longer than 40 feet (12 meters), install a CO Alarm at BOTH ends of the hallway.
Refer to state and local building codes for additional requirements.
OPTIONAL LOCKING FEATURES
The optional locking features are designed to prevent unauthorized removal of the battery or alarm. It is not necessary to activate the locks in
These CO Alarms have two separate locking features: one to lock the battery compartment, and the other to lock the CO Alarm to the mounting bracket. You can choose to use either feature independently, or use them both.
Tools you will need: •
Both locking features use locking pins, which are molded into the mounting bracket. Depending on which locking features you use, remove one or both pins from the mounting bracket using
To permanently remove either locking pin, insert a flathead screwdriver between the locking pin and the lock, and pry the pin out of the lock.
• | If the CO Alarm becomes contaminated by excessive dirt, dust and/or |
| grime, and cannot be cleaned to avoid unwanted alarms, replace the unit |
| immediately. |
• | Relocate the unit if it sounds frequent unwanted alarms. See “Where CO |
| Alarms Should Not Be Installed” for details. |
Choosing a replacement battery:
Your CO Alarm requires two standard AA batteries. The following batteries are acceptable as replacements: Energizer E91. These batteries are available at many local retail stores.
Actual battery service life depends on the CO Alarm and the environment in which it is installed. All the batteries specified above are acceptable replace- ment batteries for this unit. Regardless of the manufacturer’s suggested battery life, you MUST replace the battery immediately once the unit starts “chirping” (the “low battery warning”).
To replace the batteries (without removing Alarm from the ceiling or wall):
1. Open the battery compartment.
2. Press tabs A and B as shown in the diagram and remove each battery.
3. Insert the new batteries, making sure |
they snap completely into the battery |
or oil companies and HVAC companies offer appliance inspections for |
a nominal fee. |
• Make regular visual inspections of all |
appliances for excessive rust and scaling. Also check the flame on the |
burner and pilot lights. The flame should be blue. A yellow flame means |
fuel is not being burned completely and CO may be present. Keep the |
blower door on the furnace closed. Use vents or fans when they are |
available on all |
vented to the outside. Do not grill or barbecue indoors, or in garages |
or on screen porches. |
• Check for exhaust backflow from CO sources. Check the draft hood on |
an operating furnace for a backdraft. Look for cracks on furnace heat |
exchangers. |
• Check the house or garage on the other side of shared wall. |
• Keep windows and doors open slightly. If you suspect that CO is |
escaping into your home, open a window or a door. Opening windows |
and doors can significantly decrease CO levels. |
In addition, familiarize yourself with all enclosed materials. Read this manual in its entirety, and make sure you understand what to do if your CO Alarm sounds.
REGULATORY INFORMATION FOR CO ALARMS
Gas Detection at Typical Temperature and Humidity Ranges: The CO Alarm is not formulated to detect CO levels below 30 ppm typically. UL tested for false alarm resistance to Methane (500 ppm), Butane (300 ppm), Heptane (500 ppm), Ethyl Acetate (200 ppm), Isopropyl Alcohol (200 ppm) and Carbon Dioxide (5000 ppm). Values measure gas and vapor concentrations in parts per million.
Audible Alarm: 85 dB minimum at 10 feet (3 meters).
GENERAL LIMITATIONS OF CO ALARMS
This CO Alarm is intended for residential use. It is not intended for use in industrial applications where Occupational Safety and Health Administration (OSHA) requirements for carbon monoxide detectors must be met.
CO alarms may not waken all individuals. If children or others do not readily waken to the sound of the CO alarm, or if there are infants or family members with mobility limitations, make sure that someone is assigned to assist them in the event of an emergency.
CO Alarms will not work without power. This alarm requires a two (2) AA batteries to operate.
CO Alarms for Solar or Wind Energy users and battery backup power systems: AC powered CO Alarms should only be operated with true or pure sine wave inverters. Operating this Alarm with most
Two Silence Features |
UL STANDARD |
2034 |
Model CO511 |
Printed in Mexico |
IMPORTANT! PLEASE READ CAREFULLY AND SAVE.
This user’s manual contains important information about your Carbon Monoxide Alarm’s operation. If you are installing this Alarm for use by others, you must leave this
BEDROOM | BEDROOM | BEDROOM |
| KITCHEN | GARAGE |
LIVING ROOM | HALL |
|
| BASEMENT |
|
REQUIRED TO MEET NFPA RECOMMENDATIONS
SUGGESTED AREAS FOR INSTALLING ADDITIONAL CO ALARMS
In a
•Install at least one CO Alarm near or within each separate sleeping area.
•For added protection, install an additional CO Alarm at least 20 feet (6 meters) away from the furnace or fuel burning heat source.
In a
• Install at least one CO Alarm near or within each separate sleeping area. |
TO LOCK THE BATTERY COMPARTMENT
Do not lock the battery compartment until you install the batteries and test the CO Alarm.
If the unit does not alarm during testing, DO NOT lock the battery compartment! Install new batteries and test again.
If the CO Alarm still does not alarm, replace it immediately.
1. Using
2. After batteries are inserted, then push the locking pin through the hole near the battery door latch on the back of the CO Alarm.
TO UNLOCK THE BATTERY COMPARTMENT
1. Remove the CO Alarm from the mounting bracket. If the unit is locked to the bracket, see the section
“To Unlock the Mounting Bracket.”
2. Insert a flathead screwdriver under the head of the locking pin, and gently pry it out of the battery compartment lock. (If you plan to relock the battery compartment, save the locking pin.)
3. To relock the battery compartment, close the battery door and reinsert locking pin in lock.
4. Reattach the CO Alarm to the mounting bracket.
When replacing the batteries, always test the Alarm before relocking the battery compartment.
compartment. Match the terminals on | AB |
the ends of the batteries with the | |
terminals on the unit. |
|
4. Close the battery compartment, and then test the unit by pressing the Test/Silence button.
WHAT YOU NEED TO KNOW ABOUT CO
WHAT IS CO?
CO is an invisible, odorless, tasteless gas produced when fossil fuels do not burn completely, or are exposed to heat (usually fire). Electrical appliances typically do not produce CO.
These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline, kerosene, and propane.
Common appliances are often sources of CO. If they are not properly main- tained, are improperly ventilated, or malfunction, CO levels can rise quickly. CO is a real danger now that homes are more energy efficient.
UNDERWRITERS LABORATORIES INC. UL2034
WHAT LEVELS OF CO CAUSE AN ALARM?
Underwriters Laboratories Inc. Standard UL2034 requires residential CO Alarms to sound when exposed to levels of CO and exposure times as described below. They are measured in parts per million (ppm) of CO over time (in minutes).
UL2034 Required Alarm Points*:
•If the alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN 4 and 15 MINUTES.
•If the alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN 10 and 50 MINUTES.
•If the alarm is exposed to 70 ppm of CO, IT MUST ALARM BETWEEN 60 and 240 MINUTES.
*Approximately 10% COHb exposure at levels of 10% to 95% Relative Humidity (RH).
The unit is designed not to alarm when exposed to a constant level of 30 ppm for 30 days.
CO Alarms are designed to alarm before there is an immediate life threat. Since you cannot see or smell CO, never assume it’s not present.
• An exposure to 100 ppm of CO for 20 minutes may not affect average, |
healthy adults, but after 4 hours the same level may cause headaches. |
(uninterruptible power supply) products or square wave or “quasi sine wave” inverters will damage the Alarm. If you are not sure about your inverter or UPS type, please consult with the manufacturer to verify.
This CO Alarm will not sense carbon monoxide that does not reach the sensor. This CO Alarm will only sense CO at the sensor. CO may be present in other areas. Doors or other obstructions may affect the rate at which CO reaches the CO Alarm. For this reason, if bedroom doors are usually closed at night, we recommend you install a CO Alarm in each bedroom and in the hallway between them.
CO Alarms may not sense CO on another level of the home. For example, a CO Alarm on the second level, near the bedrooms, may not sense CO in the basement. For this reason, one CO Alarm may not give adequate warning.
Complete coverage is recommended. Place CO Alarms on each level of the home.
CO Alarms may not be heard. The alarm horn loudness meets or exceeds current UL standards of 85 dB at 10 feet (3 meters). However, if the CO Alarm is installed outside the bedroom, it may not wake up a sound sleeper or one who has recently used drugs or has been drinking alcoholic beverages. This is especially true if the door is closed or only partly open. Even persons who are awake may not hear the alarm horn if the sound is blocked by distance or closed doors. Noise from traffic, stereo, radio, television, air conditioner, or other appliances may also prevent alert persons from hearing the alarm horn. This CO Alarm is not intended for people who are hearing impaired.
INTRODUCTION
Thank you for choosing First Alert® for your Carbon Monoxide Alarm needs. You have purchased a
ONELINK® Enabled. Alarm automatically communicates with other ONELINK® enabled alarms when installed.
Exclusive Voice Warning with Location will tell you the preprogrammed location of the initiating unit and danger detected. Programmable up to 11 locations (ex. "basement"). When alarms sounds, if programmed for basement it will say "Warning, evacuate, carbon monoxide in basement" along with all other installed ONELINK® Voice alarms.
Spread Spectrum Horn Tone. Lower and varying horn frequency makes it easier for elderly with normal age related hearing loss to hear horn. Sweeps through the 2200 – 3400 Hz range.
RF Interconnect. Reliable and secure radio frequency communication between alarms. 915MHz frequency with 65,000 security codes and 3 channel frequency hopping.
Single Button Test/Silence eliminates confusion. Depending on what mode the alarm is in, pushing the button provides different functions such as testing the alarm, silencing the alarm,
• | For added protection, install at least one CO Alarm on each level of the |
| home. If you have a basement, install that CO Alarm at the top of the |
| basement stairs. |
• | For added protection, install an additional CO Alarm at least 20 feet |
| (6 meters) away from the furnace or fuel burning heat source. |
In Mobile Homes:
•Install CO Alarms on inside walls ONLY. Uninsulated outside walls and roofs of mobile homes often transfer heat and cold from outdoors.
WHERE CO ALARMS SHOULD NOT BE INSTALLED
Do NOT locate this CO Alarm:
• In garages, kitchens, furnace rooms, or in any extremely dusty, dirty or |
greasy areas. |
• Closer than 15 feet (4.6 meters) from a furnace or other fuel burning heat |
source, or fuel burning appliances like a water heater. |
• Within 5 feet (1.5 meters) of any cooking appliance. |
• In areas where temperature is colder than 40˚ F (4˚ C) or hotter than 100˚ F |
(38˚ C). These areas include unconditioned crawl spaces, unfinished attics, |
uninsulated or poorly insulated ceilings, porches, and garages. |
• In turbulent air, like near ceiling fans, heat vents, air conditioners, fresh air |
returns, or open windows. Blowing air may prevent CO from reaching the |
TO LOCK THE MOUNTING BRACKET | TO UNLOCK THE MOUNTING BRACKET | ||
1. | Using | 1. | Insert a flathead screwdriver into the |
| locking pin from the mounting bracket. |
| rectangular |
|
|
| bracket nearest to the locking pin. |
2. | Insert the locking pin through the hole on | 2. | Pry the CO Alarm away from the |
| the back of the CO Alarm as shown in the | ||
|
| bracket by pushing up on the screw- | |
| diagram. |
| |
|
| driver and turning the CO Alarm | |
|
|
| |
3. | When you attach the CO Alarm to the |
| counterclockwise (left) at the same |
| time. | ||
| mounting bracket, the locking pin’s head |
|
|
| will fit into a notch on the bracket. |
|
|
ADDING AND LINKING ADDITIONAL ONELINK® ALARMS | |
NOTE: Steps 1 through 3 need to be completed within two minutes. If | If you hear the CO alarm horn and the CO red light is flashing, |
more than two minutes pass, the Green power LED will stop blinking. | move everyone to a source of fresh air. |
Simply open the battery drawer of the second Alarm and repeat | DO NOT remove the batteries! |
steps 1 through 3. |
|
|
SYMPTOMS OF CO POISONING
These symptoms are related to CO POISONING and should be discussed with ALL household members.
Mild Exposure: Slight headache, nausea, vomiting, fatigue
Medium Exposure: Throbbing headache, drowsiness, confusion, fast heart rate.
Extreme Exposure: Convulsions, unconsciousness, heart and lung failure. Exposure to Carbon Monoxide can cause brain damage, death.
Some individuals are more sensitive to CO than others, including people with cardiac or respiratory problems, infants, unborn babies, pregnant mothers, or elderly people can be more quickly and severely affected by CO. Members of sensitive populations should consult their doctors for advice on taking additional precautions.
FINDING THE SOURCE OF CO AFTER AN ALARM
• An exposure to 400 ppm of CO may cause headaches in average, healthy |
adults after 35 minutes, but can cause death after 2 hours. |
This CO Alarm measures exposure to CO over time. It alarms if CO levels are extremely high in a short period of time, or if CO levels reach a certain minimum over a long period of time. The CO Alarm generally sounds an alarm before the onset of symptoms in average, healthy adults.
Why is this important? Because you need to be warned of a potential CO problem while you can still react in time. In many reported cases of CO exposure, victims may be aware that they are not feeling well, but become dis- oriented and can no longer react well enough to exit the building or get help. Also, young children and pets may be the first affected. The average healthy adult might not feel any symptoms when the CO Alarm sounds. However, people with cardiac or respiratory problems, infants, unborn babies, pregnant mothers, or elderly people can be more quickly and severely affected by CO. If you experience even mild symptoms of CO poisoning, consult your doctor immediately!
CO Alarms are not a substitute for a smoke alarm. Although fire is a source of carbon monoxide, this CO Alarm does not sense smoke or fire. This CO Alarm senses CO that may be escaping unnoticed from malfunctioning furnaces, appliances, or other sources. Early warning of fire requires the installation of smoke alarms.
CO Alarms are not a substitute for life insurance. Though these CO Alarms warn against increasing CO levels, BRK Brands, Inc. does not warrant or imply in any way that they will protect lives from CO poisoning. Homeowners and renters must still insure their lives.
CO Alarms have a limited life. Although the CO Alarm and all of its parts have passed many stringent tests and are designed to be as reliable as possible, any of these parts could fail at any time. Therefore, you must test your CO Alarm weekly.
CO Alarms are not foolproof. Like all other electronic devices, CO Alarms have limitations. They can only detect CO that reaches their sensors. They may not give early warning to rising CO levels if the CO is coming from a remote part of the home, away from the CO Alarm.
Two Silence Features. Temporarily silence low battery chirp for up to eight hours before replacing low battery or silence an unwanted alarm for several minutes.
Two Latching Features. Alarm Latch: Easily identifies initiating alarm even
after alarm condition has subsided. Low Battery Latch: Identifies which unit is in low battery condition.
Perfect Mount System includes a gasketless base for easy installation and a mounting bracket that keeps the alarm secure over a wide rotation range to allow for perfect alignment.
6 Year End of Life Timer. Every 24 hours of operation a counter stored in memory is updated. When the count equals 6 years of true operation meaning actually
© 2007 BRK Brands, Inc., a subsidiary of Jarden Corporation 3901 Liberty Street Road, Aurora, IL
All rights reserved.
Consumer Affairs: (800)
sensors. |
• In direct sunlight. |
• This CO Alarm is designed for use inside a |
or apartment. It is not meant to be used in common lobbies, hall- |
ways, or basements of |
Alarms are also installed in each family living unit. CO Alarms in |
common areas may not be heard from inside individual family |
living units. |
• This CO Alarm alone is not a suitable substitute for complete |
detection systems in places which house many people, like hotels |
or dormitories, unless a CO Alarm is also placed in each unit. |
• DO NOT use this CO Alarm in warehouses, industrial or commercial |
buildings, |
airplanes. This CO Alarm is specifically designed for residential |
use, and may not provide adequate protection in |
applications. |
1.Insert the batteries into the battery
drawer of the next Alarm.
DO NOT CLOSE THE DRAWER.
2. Press and hold the test button and then close the battery drawer.
3. Once you hear the unit chirp, release the test button.
The Green power LED will start to blink indicating the ONELINK® Alarm is waiting for program data
from one of the other setup ONELINK® Alarms.
4.Press and hold the test button on the first Alarm, until the second Alarm chirps and its Green power LED stops blinking. Then release the test button.
5.If you have purchased the hardwired battery
6.Repeat steps
USING THE SILENCE FEATURES
Never remove the batteries to quiet an unwanted alarm. Removing the batteries disables the alarm and removes your protection.
The Silence Feature is intended to temporarily silence the horn while you identify and correct the problem. Do not use the Silence Feature in emergency situations. It will not correct a CO problem.
The Silence Feature can temporarily quiet an unwanted alarm for several minutes. You can silence this Alarm by pressing the Test/Silence button on the alarm cover for at least
After the Test/Silence button is released, the Red LED blinks during the silence mode.
When the CO Alarm is Silenced the CO Alarm will remain silent for up to
4 minutes. After 4 minutes, if CO levels remain potentially dangerous the horn will start sounding again.
®
SILENCING THE LOW BATTERY WARNING
Carbon monoxide is an odorless, invisible gas, which often makes it difficult to locate the source of CO after an alarm. These are a few of the factors that can make it difficult to locate sources of CO:
•House well ventilated before the investigator arrives.
•Problem caused by “backdrafting.”
•Transient CO problem caused by special circumstances.
Because CO may dissipate by the time an investigator arrives, it may be difficult to locate the source of CO. BRK Brands, Inc. shall not be obligated to pay for any carbon monoxide investigation or service call.
POTENTIAL SOURCES OF CO IN THE HOME
TROUBLESHOOTING GUIDE
|
|
|
|
| If the Alarm... | Problem... | You should... |
|
|
|
|
|
|
|
|
|
|
|
|
| Horn "chirps" about once per minute. | Low battery warning. | Install two new AA batteries*. |
|
|
|
|
|
|
|
|
| Horn does three rapid "chirps" every minute; | MALFUNCTION SIGNAL. Device is not working | Units under warranty should be returned to |
| LED has 3 rapid flashes with "chirps". | properly, and needs to be replaced. | manufacturer for replacement. See “Limited |
|
|
| Warranty” for details. |
|
|
|
|
|
|
|
|
|
|
|
|
| The Alarms are linked but do not communicate with | Possible interference. Reference the Wireless | Move Alarms to different locations. Add an additional |
| each other. | Operation section of this manual. | Alarm between the unresponsive Alarms to route the |
|
|
| signal around obstructions. |
|
|
|
|
|
|
|
|
| CO Alarm goes back into alarm 4 minutes after you | CO levels indicate a potentially dangerous | IF YOU ARE FEELING SYMPTOMS OF CO |
| Silence it. | situation. | POISONING, EVACUATE your home and call 911 |
|
|
| or the Fire Department. Refer to "If The CO Alarm |
|
|
| Sounds" for details. |
|
|
|
|
|
|
|
|
| CO Alarm sounds frequently even though no high | The CO Alarm may be improperly located. Refer to | Relocate your Alarm. If frequent alarms continue, |
| levels of CO are revealed in an investigation. | “Where to Install CO Alarms” for details. | have home rechecked for potential CO problems. |
|
|
| You may be experiencing an intermittent CO problem. |
|
|
|
|
|
|
|
|
*For a list of acceptable replacement batteries, see “Regular Maintenance.”
If you have questions that cannot be answered by reading this manual, call Consumer Affairs at
BASIC SAFETY INFORMATION
• Dangers, Warnings, and Cautions alert you to important operating | ||
| instructions or to potentially hazardous situations. Pay special | |
| attention to these items. | |
• This CO Alarm is approved for use in | ||
|
| |
|
|
|
• | The CO Alarm is not designed to detect fire or any other gas. It will | |
| only indicate the presence of carbon monoxide gas at the sensor. | |
| Carbon monoxide gas may be present in other areas. | |
|
| |
|
| |
• This CO Alarm cannot operate without working batteries. | ||
| Removing the batteries for any reason, or failing to replace the | |
| batteries at the end of their service life, removes your protection. | |
• NEVER ignore any alarm. See “If Your CO Alarm Sounds” for more | ||
| information on how to respond to an alarm. Failure to respond can | |
| result in injury or death. | |
• The Silence Features are for your convenience only and will not | ||
| correct a problem. See "Using the Silence Features" for details. | |
| Always check your home for a potential problem after any alarm. | |
| Failure to do so can result in injury or death. | |
• Test this CO Alarm once a week. If the Alarm ever fails to test | ||
| correctly, have it replaced immediately! If the Alarm is not working | |
| properly, it cannot alert you to a problem. | |
• | This product is intended for use in ordinary indoor locations of | |
HOW TO INSTALL THIS ALARM
For quick installation instructions see the “Quick Installation Instructions” included.
This CO Alarm was designed to be mounted on the ceiling or wall. It is not a tabletop device. You must install this device on the ceiling or wall as outlined below. Read “Where To Install CO Alarms” before starting.
PARTS OF THIS CO ALARM
1 Test/Silence Button
2 Battery Compartment
3 Power LED
4 CO Alarm LED
Tools you will need: pencil, drill with 3/16” (5mm) drill bit,
Phillips screwdriver, hammer.
1. | Hold the mounting bracket against the ceiling (or wall) so the vertical |
| mounting slot is aligned in the 12 o’clock position and trace around the |
| inside of the mounting slots (vertical and horizontal mounting). |
2. | Put the unit where it won’t get covered with dust when you drill the |
| mounting holes. |
You have now successfully linked your new ONELINK Alarms. To add additional Alarms at a later time, follow steps 1 through 5.
WHAT YOU WILL SEE AND HEAR WITH THIS ALARM
Under Normal Operations
Voice: Silent
Horn: Silent
Power LED: Flashes Green once/minute
When You Test the Alarm
Voice: “Testing.” Horn: 4 fast beeps, pause, 4 fast beeps;
Voice: “Warning, evacuate carbon monoxide in [Location, example: “Basement”]. Evacuate.” Pause. “Highest carbon monoxide level was [CO level example: _0_ ppm]”.
CO LED: Flashes Red in sync with the horn pattern
If Battery Becomes Low or is Missing
Voice: “Replace battery in [Location, example “Basement”].” Repeated every 5 hours
Horn: chirps once a minute
Power LED: Flashes Green On for 2 seconds/Off for 2 seconds. Low Battery Latch is now engaged.
If Alarm is Not Operating Properly (MALFUNCTION SIGNAL)
Voice: “Detector error in [Location, example “Basement”], please see manual.” Repeated every 5 hours
Horn: Three rapid chirps every minute
CO LED: Flashes approximately once a minute
This silence feature can temporarily quiet the low battery warning “chirp” for up to 8 hours. You can silence the low battery warning “chirp” by pressing the Test/Silence button on the alarm cover.
Once the low battery warning “chirp” silence feature is activated, the unit continues to flash the Green light twice a minute for 8 hours. After 8 hours, the low battery “chirp” will resume. Replace the batteries as soon as possible; this unit will not operate without battery power!
To deactivate this feature: Press the Test/Silence button again. The unit will go into Test Mode and the low battery warning will resume (LED flashes and unit sounds “chirp” once a minute).
LATCHING FEATURES
Alarm Latch is activated after an Alarm is exposed to alarm levels of carbon monoxide. After CO levels drop below alarm levels, the “CO” Red LED will begin to flash On for 2 seconds/Off for 2 seconds. It will continue to flash or “latch” for about 15 minutes, to give you time to determine which unit initiated the alarm.
Low Battery Latch is activated when the Alarm is in the "low battery condition". When this occurs, the Power LED flashes Green On for 2 seconds/Off for 2 seconds for about 15 minutes. This feature is designed to help you identify which Alarm needs to have the battery replaced. Although, the Alarm will sound the low battery chirp approximately once every minute, sometimes during the initial stages of "low battery", the Alarm will chirp in greater intervals than one minute, sometimes up to several hours, until the battery reaches a steady low battery level. This innovative feature eliminates the frustration of waiting for and/or identifying which unit is chirping.
Damaged or insufficient venting: corroded or disconnected water heater vent pipe, leaking chimney pipe or flue, or cracked heat exchanger, blocked or clogged chimney opening.
Improper use of appliance/ device: operating a barbecue grill or vehicle in an enclosed area (like a garage or screened porch).
Transient CO Problems: “transient” or
The following conditions can result in transient CO situations:
1. Excessive spillage or reverse venting of fuel appliances caused by outdoor |
conditions such as: |
• Wind direction and/or velocity, including high, gusty winds. Heavy air in |
the vent pipes (cold/humid air with extended periods between cycles). |
• Negative pressure differential resulting from the use of exhaust fans. |
• Several appliances running at the same time competing for limited |
fresh air. |
• Vent pipe connections vibrating loose from clothes dryers, furnaces, |
or water heaters. |
• Obstructions in or unconventional vent pipe designs which can amplify |
LIMITED WARRANTY
BRK Brands, Inc., ("BRK") the maker of First Alert® brand products warrants | BRK shall not be liable for any incidental or consequential damages caused | |
that for a period of five years from the date of purchase, this product will be | by the breach of any express or implied warranty. Except to the extent | |
free from defects in material and workmanship. BRK, at its option, will repair | prohibited by applicable law, any implied warranty of merchantability or fitness | |
or replace this product or any component of the product found to be | for a particular purpose is limited in duration to the duration of the above | |
defective during the warranty period. Replacement will be made with a new or | warranty. Some states, provinces or jurisdictions do not allow the exclusion or | |
remanufactured product or component. If the product is no longer available, | limitation of incidental or consequential damages or limitations on how long | |
replacement may be made with a similar product of equal or greater value. | an implied warranty lasts, so the above limitations or exclusion may not apply | |
This is your exclusive warranty. | to you. This warranty gives you specific legal rights, and you may also have | |
This warranty is valid for the original retail purchaser from the date of initial | other rights that vary from state to state or province to province. | |
How to Obtain Warranty Service | ||
retail purchase and is not transferable. Keep the original sales receipt. Proof | ||
of purchase is required to obtain warranty performance. BRK dealers, service | Service: If service is required, do not return the product to your retailer. | |
centers, or retail stores selling BRK products do not have the right to alter, | In order to obtain warranty service, contact the Consumer Affairs Division at | |
modify or any way change the terms and conditions of this warranty. | ||
This warranty does not cover normal wear of parts or damage resulting from | Friday. To assist us in serving you, please have the model number and date of | |
purchase available when calling. For Warranty Service return to: | ||
any of the following: negligent use or misuse of the product, use on improper | ||
voltage or current, use contrary to the operating instructions, disassembly, | BRK Brands, Inc., 25 Spur Drive, El Paso, TX 79906 | |
repair or alteration by anyone other than BRK or an authorized service center. | Battery: BRK Brands, Inc. make no warranty, express or implied, written or | |
Further, the warranty does not cover Acts of God, such as fire, flood, | oral, including that of merchantability or fitness for any particular purpose with | |
hurricanes and tornadoes or any batteries that are included with this unit. | respect to battery. |
family living units. It is not designed to measure CO levels in com- |
pliance with Occupational Safety and Health Administration (OSHA) |
commercial or industrial standards. Individuals with medical condi- |
tions that may make them more sensitive to carbon monoxide may |
consider using warning devices which provide audible and visual |
signals for carbon monoxide concentrations under 30 ppm. |
For additional information on carbon monoxide and your medical |
condition contact your physician. |
WIRELESS OPERATION
First Alert® ONELINK® Technology is the easy,
The communication distance (range) between any two ONELINK® Alarms is typically 50 feet (15 meters) inside of a home. Some features of a home, such as the number of floors, number/size of rooms, furniture and types of building materials used may reduce the range of the Alarms. Examples include: sus- pended ceilings, ductwork, large metallic appliances (refrigerators) and metal studs. A feature of ONELINK® Alarms is that they operate as a mesh network. All Alarms will repeat any alarm signal that is received to all other ONELINK® Alarms. Interference from structural conditions can be overcome by adding
3. | Using a 3/16” (5 mm) drill bit, drill a hole through the center of the oval |
| outlines you traced. |
4. | Insert the plastic screw anchors (in the plastic bag with screws) into the |
| holes. Tap the screw anchors gently with a hammer, if necessary, until they |
| are flush with the ceiling or wall. |
5. | Line the mounting bracket up over the plastic screw anchors. |
6. | Screw the mounting bracket to the ceiling or wall through the mounting |
| slots using the two screws provided. |
7. | Attach the CO Alarm to the mounting |
bracket. Line up the guides on the alarm’s base with the guides on the mounting bracket. When guides are lined up, turn the base clockwise (right) until it snaps into place.
NOTE: Once the Alarm is snapped onto the mounting bracket, you can rotate the Alarm to adjust the alignment.
8. Test the CO Alarm. See “Weekly Testing” for details.
Alarm Levels of CO are Detected
Horn: 4 fast beeps, pause, 4 fast beeps, pause*
Voice: “Warning, evacuate carbon monoxide in [Location, example: “Basement”]. Evacuate.” Pause. “Highest carbon monoxide level was [CO level example: ___ ppm]”.
Horn: 4 beeps, pause, 4 beeps, pause repeating 2 times followed by Voice Warning above.
CO LED: During Alarm: Flashes Red in sync with the horn pattern. After Alarm: Flashes Red On for 2 seconds/Off for 2 seconds. CO Alarm Latch is now engaged.
*NOTE: If unit goes into CO alarm, the regular 4
CO Alarm is Silenced
Horn: Off
CO LED: Flashes Red
IF YOUR CO ALARM SOUNDS
What You See and Hear
WEEKLY TESTING
•Test the CO Alarm once a week. If the CO Alarm ever fails to test properly, have it replaced immediately! If the CO Alarm is not working properly, it cannot alert you to a problem.
•DO NOT stand close to the Alarm when the horn is sounding. Exposure at close range may be harmful to your hearing. When testing, step away when horn starts sounding.
It is important to test this unit every week to make sure it is working properly. Using the test button is the recommended way to test this CO Alarm.
You can test this CO Alarm by pressing and holding the Test/Silence button on the Alarm cover (typically
During testing, you will see and hear the following sequence:
•The Horn will sound 4 beeps, pause, 4 beeps. The Power LED will be Off and the CO LED flashes Red.
If the unit does not alarm, make sure the batteries are correctly installed, and test again. If the unit still does not alarm, replace it immediately.
| the above situations. |
2. | Extended operation of unvented fuel burning devices (range, oven, |
| fireplace). |
3. | Temperature inversions, which can trap exhaust close to the ground. |
4. | Car idling in an open or closed attached garage, or near a home. |
These conditions are dangerous because they can trap exhaust in your home. Since these conditions can come and go, they are also hard to recreate during a CO investigation.
5
For your records, please record:
Date Purchased: _______________Where Purchased: __________________
Date Installed: ____________/____________Month/Year
Replacement date is five years after installation:
_____________/____________Month/Year
NOTE: End of Life Signal — Once the unit reaches the end of its lifecycle, the MALFUNCTION SIGNAL will sound once a minute to indicate the need to immediately replace the Alarm.
First Alert® is a registered trademark of the First Alert Trust used under license. ONELINK® is a trademark of BRK Brands, Inc.
6
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Basic Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Wireless Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Where to Install This Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Where CO Alarms Should NOT Be Installed . . . . . . . . . . . . . . . . . . . . . .2 How to Install This Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Step By Step Guide to Programming This Alarm | |
Adding and Linking Additional ONELINK® Alarms | . .3 |
What You Will See and Hear With This Alarm | . .3 |
Optional Locking
If Your CO Alarm
Weekly Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 What You Need To Know About CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 What is CO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Symptoms of CO Poisoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Finding the Source of CO after an Alarm . . . . . . . . . . . . . . . . . . . . . . . .5 Potential Sources of CO in the Home . . . . . . . . . . . . . . . . . . . . . . . . . . .5
How Can I Protect My Family From CO Poisoning? | . .6 |
Regulatory Information For CO Alarms | |
Underwriters Laboratories Inc. UL 2034 |
General Limitations Of CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Troubleshooting
Limited
Printed in Mexico
7
additional Alarms to route the wireless signal around obstructions.
•The range and proper operation of any wireless device will vary depending on its surroundings. It is very important that each Alarm is tested individually before and after installation to make sure that all Alarms respond properly.
•The ONELINK® Alarms are not to be used outdoors or to transmit between buildings. The Alarms will not communicate properly under these conditions.
•Metal objects and metallic wallpaper may interfere with signals from wireless Alarms. Alarms should be tested after changes to your home such as remodeling, moving furniture, and with metal doors opened and closed.
Your First Alert® ONELINK® CO Alarm will automatically communicate both potential fires and carbon monoxide presence with all other First Alert® ONELINK® Smoke/CO Alarms.
FCC NOTICE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC ID: M7U5001L
Changes or modifications not expressly approved by BRK Brands, Inc. could void the user’s authority to operate the equipment.
1
STEP BY STEP GUIDE TO PROGRAMMING THIS ALARM
FOR FIRST TIME AND WHEN CHANGING BATTERIES
| Action: | Alarm Will Say: |
|
| 1. Insert batteries (2, AA batteries). | “Welcome, First Alert Carbon | |
|
| Monoxide Alarm.” | |
|
| “No location programmed” if first | |
|
| time or “[Location, example: | |
|
| “Basement”] location programmed” | |
|
| when changing batteries. | |
|
| “To select location, press and hold | |
|
| test button now.” | |
| 2. Press & Hold Test Button if you | “To save location, press and hold test | |
| would like to program the location | button after location is heard.” Alarm | |
| or change the location of the | will speak list of locations (see | |
| Alarm. Release button after Alarm | below). | |
| responds. |
|
|
|
|
|
|
| 3. After you hear the location of where | “[Location, example: “Basement”] | |
| you are placing the Alarm, Press & | location saved.” | |
| Hold the Test Button. | If no location is chosen: | |
|
| “No location saved.” | |
Refer to section “What You Will See and Hear With This Alarm”.
Actuation of your CO Alarm indicates the presence of carbon monoxide (CO) which can kill you. In other words, when your CO Alarm sounds, you must not ignore it!
IF THE ALARM SIGNAL SOUNDS
1.Operate the Test/Silence button.
2.Call your emergency services, fire department or 911. Write down the number of your local emergency service here:
________________________________________________________________
3.Immediately move to fresh
4.After following steps
________________________________________________________________
Alarms have various limitations. See "General Limitations of CO Alarms" for details.
3 | 4 |
