INSTALLATION INSTRUCTIONS
MODEL: 62BK244CBK, 62BK244CCN, 62BK244CCY, 62BK244CMP, 62BK244TBK, 62BK244TCY, 62BK244TGK, 62BK244TMP
RECESSED MOUNTED,
STEEL MEDICINE CABINETS
For help, call us
toll free!
MODEL | WALL OPENING | OVERALL SIZE | ||||
NO. | W | H | D | W | H | D |
62BK244CBK | 141/4 24 | 4 | 161/2 261/2 51/4 | |||
62BK244CCN | 141/4 24 | 4 | 161/2 261/2 51/4 | |||
62BK244CCY | 141/4 24 | 4 | 161/2 261/2 51/4 | |||
62BK244CMP | 141/4 24 | 4 | 161/2 261/2 51/4 | |||
62BK244TBK | 141/4 24 | 4 | 161/2 261/2 51/4 | |||
62BK244TCY | 141/4 | 24 | 4 | 161/2 | 261/2 | 51/4 |
62BK244TGK | 141/4 | 24 | 4 | 161/2 | 261/2 | 51/4 |
62BK244TMP | 141/4 | 24 | 4 | 161/2 | 261/2 | 51/4 |
1.Carefully remove all packing material. Place hardware packages, shelves and door aside until needed. Hardware and shelves are located in the fillers identified by “Hardware Enclosed” tape.
2.Determine desired location of cabinet on wall. Mark wall to show wall opening size (see dimension chart). Generally, the recommended height to the center of the cabinet is 64” from the floor. (Fig. 1)
3.CAUTION: Wall studs, plumbing or electrical lines that interfere must be removed or relocated. Cut wall opening, being careful not to damage the surrounding wall surface. Insert framing to support all plaster board edges.
4.Prepare the mounting screws by placing the screws into the plastic bases. (Fig. 2)
5.Note: For ease of installation, an additional person is recommended. Insert cabinet into wall opening. (Fig.3) Ensure the cabinet is plumb and level. If necessary use a carpenter’s level and shim corners of cabinet. Secure to wall studs through the four (4) mounting holes inside cabinet, using the screws that have been placed into the plastic bases. (Fig. 4) Do not over tighten the mounting screws as the body side wall may bend and prevent proper shelf installation. Only tighten screws until they are flush with the body.
6.Snap the screw covers over the screw bases. (Fig.5)
INSTALLATION of DOORS1. Remove hinges and screws from hardware bag. Mount |
hinge unit on door as shown in Fig. 6 securing with screws |
provided. |
Fig. 1 | Fig. 2 |
Insert screw through clear plastic base
Fig. 3 | Wall | Fig. 4 |
| Opening | |
|
| |
|
| Mounting |
|
| Screws |
|
| Mounting |
|
| screw into |
|
| mounting |
|
| hole |
Cabinet |
|
|
Body |
|
|
Fig. 5 |
| Fig. 6 |
|
| Hinge Mounted |
Snap on Cover |
| to Door |
Cover |
| |
|
| |
Screw |
|
|
Base
2. | Install the door by inserting door side of the hinge into the |
| bracket on the body shown in Fig. 7. |
3. | Check door for proper alignment. If the door needs to be |
| adjusted please refer to the adjustment procedures in Fig. 8. |
1. | Select where you want the shelves to be placed. |
2. | Insert two (2) shelf brackets at each end of the shelf |
Fig. 7
Hinge Mounted to Cabinet
Press down on hinge until it clips in place
Hook bottom of hinge into place on the bracket
Fig. 8
This screw for
Door Adjustment up and down adjustments
This screw for depth adjustments
This screw
for left and right adjustments
| location. (Fig. 9). |
3. | Set shelves in place on the shelf brackets, pressing down |
| on the shelf to lock in place. (Fig. 9). |
4. | Remove hole plugs from hardware bag and place in |
| remaining holes. (Fig. 10). |
5. | Remove bumpers from hardware bag and position to |
| body. (Refer to Service Parts Drawing - Key No. 9 for |
| bumper locations). |
Fig. 9 | Fig. 10 |