B100 TWO CHANNEL POWER AMPLIFIER

batteries are correctly oriented and properly seated in the battery holder.

The B100 remote is a full function remote. It allows selection of all sources, volume up or down (the volume control is a motor-driven design), mute ,left/right balance, power on/off and discrete code entry.

We recommend maintaining a direct line-of-sight between the hand held remote unit and the front of the B100 to ensure the most efficient operation of the remote features.

PROGRAMMING the HANDHELD REMOTE CONTROL:

The automatic motion-sensing backlight function in the handheld infra-red remote control unit can be disabled by entering the 3 digit code “792” as follows:

1)Press and hold the CODE button for 5 seconds. Release when the LED flashes red.

2)After the LED stops flashing, enter the 3 digit code “792” by pressing the buttons D1, D3 then AUX/PH (see illustra- tion on page 3)

3)To re-enable the motion-sensing backlight function, repeat steps 1 and 2 above

To completely disable the backlight, enter the 3 digit code “797” as follows:

1)Press and hold the CODE button for 5 seconds. Release when the LED flashes red.

2)After the LED stops flashing, enter the 3 digit code “797” by pressing the buttons D1, D3 then D1 (see illustration on page 3)

3)To re-enable the backlight repeat steps 1 and 2 above

SENDING CODES to the B100 via the IR HANDHELD REMOTE CONTROL:

Press the CODE button on the remote control (the red LED will light) and then enter the 3 digt code, as listed in the “Wired RS232 Remote Control” section” below . The LED will flash to confirm transmission and then extinguish.

WIRED RS232 REMOTE CONTROL:

Using the DB9-female connector at the rear of the unit, the B100 can receive commands via a null modem cable at 9600 baud, 8 data bits, no parity and 1 stop bit (9600,8,N,1). Valid commands will return the “>” character indicating that the unit is ready to receive a new command. An invalid command will return the “!” character. These serial data

commands are as follows:

 

 

 

- select digital source 1 (D1)

000

- power off

015

- power on/off toggle

081

001

- select analog source 1 (A/D)

019

- balance left

082

- select digital source 2 (D2)

002

- select analog source 2 (AUX/PH)

020

- balance right

083

- select digital source 3 (D3)

003

- select analog source 3 (CD)

029

- power on

084

- select digital source 4 (D4)

004

- select analog source 4 (TUNER)

058

- mute on

245

- set/reset Pass Through mode

005

- select analog source 5 (TV)

059

- mute off

247

- Set Trigger 2 for current source

006

- select analog source 6 (VIDEO)

061

- record monitor toggle

248

- Clear Trigger 2 for current source

007

- volume up

062

- record monitor on

255

- System reset; restore defaults

008

- volume down

063

- record monitor off

 

 

PASS THROUGH MODE:

PASS THROUGH mode sets the pre-amp gain to 1 (unity gain) and locks out the volume & balance controls for any single analog audio source. For example, if the Front Left and Front Right outputs of a home theater surround sound processer were connected to the TV input of the B100, and then PASS THROUGH was engaged then whevever TV input is selected the volume and balance controls would be locked at unity gain. If other inputs were subsequently selected, volume and balance controls return to normal operation for those other input sources. Only the TV inputs would be locked at unity gain. PASS THROUGH mode, therefore, can only be assigned to one input at a time, but that input can be any one of the analog audio inputs. The power amplifier stage is not affected by PASS THROUGH mode. PASS THROUGH mode can only be set (or reset) by sending the 3 digit code “245” to the B100 either from the handheld IR remote control or via the RS232 serial data input. See “Sending Codes to the B100 via the IR Handheld

4

Page 6
Image 6
Bryston B100, B100-DA, B100-P Programming the Handheld Remote Control, Wired RS232 Remote Control, Pass Through Mode

B100, B100-DA, B100-P, B100 specifications

Bryston, a Canadian audio company renowned for its high-performance audio products, offers an impressive line of integrated amplifiers, with the B100 series standing out for audiophiles. The B100, B100-DA, and B100-P models incorporate advanced features designed to deliver exceptional sound quality and versatility.

The Bryston B100 is a powerful integrated amplifier that combines the performance of a high-end power amplifier with a preamplifier's flexibility. It features an impressive power output of 120 watts per channel into 8 ohms, ensuring it can drive a wide range of speakers effortlessly. Its all-brass construction and meticulous engineering ensure low distortion and high reliability, which are hallmarks of Bryston products. Furthermore, the B100 employs a classic analog design that retains the warmth and character associated with traditional audio systems.

The B100-DA model enhances this already excellent foundation by integrating a high-quality digital-to-analog converter (DAC). This addition allows direct connections to digital sources, such as computers and streaming devices, supporting various digital formats with ease. The B100-DA features USB and optical inputs, eliminating the need for an external DAC while ensuring superb sound quality from digital sources. This combination of analog and digital capabilities makes the B100-DA an exceptionally versatile choice for modern audiophiles.

Adding to the lineup is the B100-P, which offers even more flexibility with an optional phono stage. This model is tailored for vinyl enthusiasts, providing a dedicated input designed to optimize the sound quality of vinyl playback. With the B100-P, users can connect their turntables directly, enjoying the rich, warm sound that only analog vinyl can provide. This model further exemplifies Bryston’s commitment to accommodating traditional and contemporary audio setups.

All B100 models incorporate Bryston’s proprietary circuit designs that minimize noise and distortion, resulting in an ultra-clean audio signal. The robust build quality and attention to detail ensure longevity, with Bryston's renowned 20-year warranty adding peace of mind for users.

In summary, the Bryston B100 series represents the pinnacle of integrated amplifier design, catering to a diverse range of listening preferences and technologies while maintaining the high-fidelity audio performance that has become synonymous with the Bryston brand. Whether you choose the standard B100, the digital-friendly B100-DA, or the vinyl-focused B100-P, you are guaranteed a premium audio experience that is sure to impress.