ELECTRICAL REQUIREMENTS

WARNING - The dispenser must be disconnected from the power source until specified in Initial Set-Up.

Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.

WHITE

NEUTRAL WHITE

NEUTRAL

N

 

L1 BLACK

L1

 

 

L1 BLACK

 

GREEN

 

G

120 volt ac models

POWER CORD

 

L2 RED

 

 

L1 BLACK

 

 

 

NEUTRAL BLUE

POWER CORD

L2 RED

L2 RED

POWER CORD

N

 

 

 

L2

L1

L1 BLACK

L1

L1 BROWN

L1 BLACK

GREEN/YELLOW

GREEN

 

G

G

230 volt ac models

208 & 240 volt ac models

Note: This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate conductor for earth ground.

Note: This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate conductor for earth ground.

Note: This electrical service consists of 2 current carrying conductors (L1 and L2) and a separate conductor for earth ground.

Electrical Hook-Up

CAUTION – Improper electrical installation will damage electronic components.

1.An electrician must provide electrical service as specified.

2.Using a voltmeter, check the voltage and color coding of each con- ductor at the electrical source.

3.Turn off master switch (if equipped).

4.Remove the upper and lower rear panels (side panel on H10X).

5.Install the proper electrical wiring to the terminal block.

6.On Dual Volt models, make sure the toggle switch below the circuit board is set to the desired voltage (120 volts or 208/240 volts) and the red switch on the circuit board is in the “SET” position.

7.Connect the dispenser to the power source and verify the voltage at the terminal block before proceeding. Reinstall both rear panels.

8.If plumbing is to be hooked-up later be sure the dispenser is discon- nected from the power source. If Plumbing has been hooked-up, the dispenser is ready for Initial Set-Up.

L2 RED

L2 RED

POWER CORD

 

L2

 

WHITE

NEUTRAL WHITE

 

NEUTRAL

N

 

 

 

L1 BLACK

L1 BLACK

 

 

L1

 

GREEN

G

120/208 & 120/240V ac

single phase models

Note: This electrical service consists of 3 current carrying conductors (Neutral, L1 and L2) and a separate conductor for earth ground.

DUAL VOLT TOGGLE SWITCH

CE REQUIREMENTS

This appliance must be installed in locations where it can be overseen by trained personnel.

For proper operation, this appliance must be installed where the tem- perature is between 5°C to 35°C.

Appliance shall not be tilted more than 10° for safe operation.

An electrician must provide electrical service as specified in conformance with all local and national codes.

This appliance must not be cleaned by water jet.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experi-

ence and knowledge, unless they have been given instructions concerning use of this appliance by a person responsible for its safety.

Children should be supervised to ensure they do not play with the appliance.

If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.

4

39338.1 072409

 

Page 4
Image 4
Bunn H5E, H5X, DV PC manual Electrical Requirements, CE Requirements, Electrical Hook-Up, Dual Volt Toggle Switch

DV PC, H5E, H5X specifications

The Bunn H5E and H5X coffee machines represent a leap forward in brewing technology, specifically tailored for commercial use. Both models focus on delivering high-quality coffee while maximizing efficiency, making them ideal choices for busy cafés and restaurants.

The Bunn H5E features a unique 5-liter dual tank system, which allows for faster brewing times and reduces wait periods for customers. This dual tank setup facilitates the simultaneous preparation of multiple coffee types, catering to a diverse clientele. The H5X, on the other hand, is equipped with advanced electronic controls that permit precise temperature adjustments to ensure that the ideal brewing conditions are maintained, enhancing flavor extraction.

One of the standout features of both models is the patented BrewOptimized Technology. This technology helps maintain optimal water temperature and consistent flow rates throughout the brewing process, ensuring that each cup of coffee meets the high standards expected in commercial settings. Additionally, the units utilize a patented stainless steel brew basket that enhances durability and simplifies cleaning, making maintenance less of a chore for busy staff.

Another significant characteristic of the H5E and H5X is their programmable settings, which allow operators to customize brewing parameters according to their specific preferences or customer needs. This flexibility means that establishments can experiment with various coffee profiles, ensuring that they serve only the best products to their patrons.

Safety is also a priority in the design of these machines. The H5E and H5X come equipped with built-in safety features such as automatic shut-off and thermal overload protection, which help to prevent accidents and enhance longevity. Moreover, their compact design allows for easy installation in a variety of settings, whether it's a small coffee stand or a large restaurant operation.

Both the Bunn H5E and H5X models are energy-efficient, with features that minimize power consumption without compromising performance. This focus on sustainability not only helps reduce overhead costs but also appeals to environmentally conscious consumers.

In summary, the Bunn H5E and H5X coffee machines are engineered for high performance, reliability, and versatility. With features designed to provide quick, quality coffee while ensuring ease of operation and maintenance, these machines are ideal for any establishment that takes its coffee seriously. Whether you’re brewing for a crowd or crafting specialty drinks, the H5E and H5X stand ready to deliver excellent results every time.