Light Installation
Note: Clear light is mounted facing forward, on side closest to traffic. Red light is mounted facing rear, on the side closest to traffic.
Note: Make sure on/off light switches are accessible.
1.Remove clips and screws from back of lights.
2.Using screws, fasten brackets and lights together.
3.Mount clear light/bracket diagonally on front of roll bar and red light/bracket on rear of roll bar, both on side closest to traffic. Photo 1
Front of Trailer
Red Light
Roll Bar
Clear Light
PHOTO 1: Light Installation
Light Installation
Note: Clear light is mounted facing forward, on side closest to traffic. Red light is mounted facing rear, on the side closest to traffic.
Note: Make sure on/off light switches are accessible.
1.Remove clips and screws from back of lights.
2.Using screws, fasten brackets and lights together.
3.Mount clear light/bracket diagonally on front of roll bar and red light/bracket on rear of roll bar, both on side closest to traffic. Photo 1
Front of Trailer
Red Light
Roll Bar
Clear Light
PHOTO 1: Light Installation
Locking Quick Release/
Wheel Installation
and Operation
1.With quick release lever in “open” position, insert wheel axle completely into trailer axle receiver.
2.Close quick release lever, with lever aimed towards rear of trailer. Photo 2
3.Verify that tires are inflated to pressure marked on the tire side wall.
4.To remove wheel from trailer axle, push locking button on side of quick release lever and open lever.
Note: The locking quick release lever securely attaches the wheel to the trailer. If you have difficulty removing the wheel, release pressure on the quick release by pushing the end of lever in toward the trailer before pushing the locking button.
Quick
Release
Lever
| Rear of Trailer |
| Locking |
| Button | ||
PHOTO 2: Wheel Installation |
| ||
Locking Quick Release/
Wheel Installation
and Operation
1.With quick release lever in “open” position, insert wheel axle completely into trailer axle receiver.
2.Close quick release lever, with lever aimed towards rear of trailer. Photo 2
3.Verify that tires are inflated to pressure marked on the tire side wall.
4.To remove wheel from trailer axle, push locking button on side of quick release lever and open lever.
Note: The locking quick release lever securely attaches the wheel to the trailer. If you have difficulty removing the wheel, release pressure on the quick release by pushing the end of lever in toward the trailer before pushing the locking button.
Quick
Release
Lever
| Rear of Trailer |
| Locking |
| Button | ||
PHOTO 2: Wheel Installation |
| ||
WARNING
MAKE SURE WHEELS ARE HELD SECURELY,
WITH WHEEL SHAFT FULLY INSERTED INTO
AXLE RECEIVER. YOU SHOULD NOT BE ABLE
TO ROCK OR SHIFT WHEELS. IMPROPERLY
INSTALLED WHEELS CAN FALL OFF, CAUSING
AN ACCIDENT OR SERIOUS INJURY.
BURLEY DESIGN
Copyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC : Rev 06/08 : 170056 Euro d’lite, Encore and Solo Installation Instructions r1
4020 Stewart Rd. Eugene, OR 97402 : PH 541. 687.1644 800.423. 8445 FAX 541.687.0436 : burley@burley.com : www.burley.com
WARNING
MAKE SURE WHEELS ARE HELD SECURELY,
WITH WHEEL SHAFT FULLY INSERTED INTO
AXLE RECEIVER. YOU SHOULD NOT BE ABLE
TO ROCK OR SHIFT WHEELS. IMPROPERLY
INSTALLED WHEELS CAN FALL OFF, CAUSING
AN ACCIDENT OR SERIOUS INJURY.
BURLEY DESIGN
Copyright © 2008 by Burley Design LLC. “Burley” is a registered trademark of Burley Design LLC : Rev 06/08 : 170056 Euro d’lite, Encore and Solo Installation Instructions r1
4020 Stewart Rd. Eugene, OR 97402 : PH 541. 687.1644 800.423. 8445 FAX 541.687.0436 : burley@burley.com : www.burley.com
