Campbell Hausfeld IFN21950 6

Operating Instructions

OPERATING INSTRUCTIONS		3.	Make sure the trigger	LOADING THE NAILER
(Continued)			and work contact	1.	Always connect the tool to the air
MODE CONVERSION			element (WCE) move		supply before loading fasteners.
MODE CONVERSION			freely up and down		supply before loading fasteners.
To convert the tool from one mode to			freely up and down	2.	Pull nail pusher	Nail Pusher Latch
To convert the tool from one mode to			without sticking or	2.	Pull nail pusher
the other:			without sticking or		mechanism back
the other:			binding.		mechanism back	Mechanism
1. Remove o-ring on the side of trigger			binding.		until pusher	Mechanism
					until pusher
					engages with
	pin.				engages with
	pin.				magazine latch.
2. Remove trigger pin, trigger, and		4.	Reconnect air supply		magazine latch.
2. Remove trigger pin, trigger, and		4.	Reconnect air supply
	trigger spring.		to the tool.
3. Switch out only the trigger.				3.	Load strips of
4.	Replace trigger spring, trigger,	5.	Depress the Work		fasteners into
	trigger pin, and o-ring.	5.	Depress the Work		the magazine
	trigger pin, and o-ring.		Contact Element		the magazine
Do not attempt to modify the trigger			Contact Element		slot. Make sure
			(WCE) against		slot. Make sure
			(WCE) against		that the nails are
components in any manner and do			the work surface		that the nails are
components in any manner and do			the work surface		placed into tool
not attempt to use any other trigger			without pulling		placed into tool
not attempt to use any other trigger			without pulling		at the proper
components other than those intended			the trigger. The		at the proper
components other than those intended			the trigger. The		orientation.
for this tool.			tool MUST NOT		orientation.
for this tool.			tool MUST NOT	4.	Squeeze the
Contact your Campbell Hausfeld			OPERATE. Do not use the tool if it	4.	Squeeze the
Contact your Campbell Hausfeld			OPERATE. Do not use the tool if it		pusher and the
representative if you have any			operates without pulling the trigger.		pusher and the
representative if you have any			operates without pulling the trigger.		latch together to
questions.			Personal injury may result.		latch together to
questions.			Personal injury may result.		unlatch pusher.
		6.	Remove the tool		unlatch pusher.
Mode Conversion		6.	Remove the tool		Make sure the
Mode Conversion			from the work		Make sure the
	Trigger spring		from the work		head of the last
	Trigger spring		surface. The		head of the last
			surface. The		nail is under the
	O-ring		Work Contact		nail is under the
			Work Contact		head of the pusher.
			Element (WCE)


	Trigger		must return	UNLOADING THE NAILER
	Trigger		to its original
			to its original	1. Always unload all fasteners before
			down position. The tool MUST NOT	1. Always unload all fasteners before
			down position. The tool MUST NOT		removing tool from service.
			OPERATE. Do not use the tool if it		removing tool from service.
			OPERATE. Do not use the tool if it		Unloading is the reverse of loading,
			operates while lifted from the work		Unloading is the reverse of loading,
	Trigger pin		operates while lifted from the work		except always disconnect the air
	Trigger pin		surface. Personal injury may result.		hose before unloading.
			surface. Personal injury may result.		hose before unloading.
		7.	Pull the trigger	2.	Pull nail pusher Nail Pusher Latch
OPERATING A SEQUENTIAL TRIP TOOL			and depress the	2.	Pull nail pusher Nail Pusher Latch
OPERATING A SEQUENTIAL TRIP TOOL			and depress the		mechanism back	Mechanism
	Check the operation		work contact		until pusher	Mechanism
	Check the operation		work contact		until pusher
	of the Work Contact		element (WCE)		engages with
Element (WCE) trip mechanism before			against the work surface. The tool		engages with
Element (WCE) trip mechanism before			against the work surface. The tool		magazine latch.
each use. The WCE must move freely			MUST NOT OPERATE IF IN SINGLE		magazine latch.
each use. The WCE must move freely			MUST NOT OPERATE IF IN SINGLE
without binding through its entire			CYCLE MODE (black trigger). The
travel distance. The WCE spring must			CYCLE MODE (black trigger). The
travel distance. The WCE spring must			tool MUST OPERATE IF IN BOTTOM
return the WCE to its fully extended			tool MUST OPERATE IF IN BOTTOM	3.	Hold tool upright
return the WCE to its fully extended			TRIP MODE (red trigger).	3.	Hold tool upright
position after being depressed. Do			TRIP MODE (red trigger).		so nails will
not operate the tool if the WCE trip					so nails will
not operate the tool if the WCE trip		8.	Depress the		slide backwards
mechanism is not operating properly.		8.	Depress the		slide backwards
mechanism is not operating properly.			Work Contact		toward magazine
Personal injury may occur.			Work Contact		toward magazine
Personal injury may occur.			Element (WCE)		slot.
1.	Disconnect the air		Element (WCE)		slot.
1.	Disconnect the air		against the
	supply from the tool.		against the
	supply from the tool.		work surface.
			work surface.
			Pull the trigger. The tool MUST	4.	Squeeze the
2.	Remove all fasteners		OPERATE.		pusher and
2.	Remove all fasteners		An improperly		latch together
	from the magazine		functioning tool		to unlatch the
	(see Loading /	must not be used. Do not actuate the			pusher once all
	Unloading).	tool unless the tool is placed ﬁrmly			nails have been
	Unloading).	against the work piece.			nails have been
		against the work piece.			removed.
					removed.
www.chpower.com