
Operating Instructions |
|
|
|
|
|
|
| NB006401 | |||
User - Maintenance | Technical Service |
|
| Assembly Procedure For Seals | |||||||
Instructions | Please call our Tool Hotline at | When repairing a tool, the internal | |||||||||
Clearing A Jam From The Tool | parts must be cleaned and lubricated. | ||||||||||
1. | Disconnect the air | the operation or repair of this tool or | Parker | ||||||||
for additional copies of this manual. | used on all | ||||||||||
| supply from the | ||||||||||
|
|
|
|
| coated with | ||||||
| tool. | Fastener And Replacement |
| ||||||||
|
| A small amount of oil must be used on | |||||||||
|
| Parts |
|
|
| ||||||
|
|
|
|
| all moving surfaces and pivots. After | ||||||
|
|
| Use only headless | ||||||||
2. | Remove all nails |
| reassembling, a few drops of 30W |
| |||||||
| micropins, 16 gauge. |
| |||||||||
| |||||||||||
| from the magazine | Tool performance, safety and durability | |||||||||
| be added through the air line before | ||||||||||
| (see Loading/ | could be reduced if improper fasteners | |||||||||
| are used. When ordering replacement | testing. |
|
|
| ||||||
| Unloading). Failure |
|
|
| |||||||
| parts or fasteners, specify by part |
|
|
|
|
|
| ||||
| to do so will cause |
| Storage |
|
|
| |||||
| number. |
|
|
|
|
|
| ||||
| the nails to eject |
|
|
|
|
|
| ||||
| Tool Repair |
|
|
| The tool should be stored in a cool dry | ||||||
| from the front of the tool. |
|
|
| |||||||
|
|
|
| place. |
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
3. | Undo hook by | Only qualified personnel should repair |
|
|
|
| |||||
|
|
|
|
| |||||||
the tool and they should use genuine |
|
|
|
|
| ||||||
| pushing down on |
|
|
|
|
| |||||
| Campbell Hausfeld replacement parts |
|
|
|
|
| |||||
| the buttons on |
|
|
|
|
| |||||
| and accessories, or parts and accessories |
|
|
|
|
| |||||
| the sides of the |
|
|
|
|
| |||||
| which perform equivalently. |
|
|
|
|
|
| ||||
| magazine. The |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
| buttons will disengage the hook |
|
|
|
|
|
|
|
|
| |
| from the nose. | Fasteners |
|
|
|
|
|
|
|
| |
4. | The door can |
|
|
|
|
|
|
|
| ||
The following Campbell Hausfeld finishing nails are available at local retail stores. | |||||||||||
| now be rotated, | ||||||||||
| If you need help locating any item, call customer service at |
| |||||||||
| exposing the |
| |||||||||
| Campbell Hausfeld nails meet or exceed ASTM Standard F1667. |
|
| ||||||||
| jammed fastener. |
|
| ||||||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| Nails | Nails | |
5. | Remove the |
|
| Shank |
|
|
|
| Per | Per | |
Model | Length | Gauge | Finish | Head | Collation | Stick | Box | ||||
| jammed fastener, | ||||||||||
| FB005060 | 2 | 16 | Galvanized | Brad | Adhesive | 50 | 2500 | |||
| using pliers or | ||||||||||
| a screwdriver if |
| inch | Gauge |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
| required. | FB160025 | 1 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | ||
6. Rotate door back into the closed |
| inch | Gauge |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
| position. | FB160040 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | |||
7. Push buttons down again to lift the |
| inch | Gauge |
|
|
|
|
|
| ||
FB160050 | 2 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | ||||
| hook. Close the door and release the | ||||||||||
| buttons to reengage the hook with |
| inch | Gauge |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
| the nose. | FB160065 | 16 | Galvanized | Brad | Adhesive | 50 | 1000 | |||
8. | Make sure the |
| inch | Gauge |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
| trigger and work | Interchange Information |
|
|
|
|
|
| |||
| contact element |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
| (WCE) move freely | Nails used in the Campbell Hausfeld NB006401 Finishing Nailer will also work in | |||||||||
| up and down | Hitachi NT65A, Paslode | |||||||||
| without sticking or binding. | Cable FN200 and FN250. |
|
|
|
|
|
|
www.chpower.com | 6 |