Operating Instructions

Important Safety Instructions

operation, breakage of the tool or

 

Operating Instructions

(Continued)

serious injury to persons.. Use only

 

Lubrication

 

Clean and check all

clean, dry, regulated compressed air

 

This tool requires lubrication before

air supply hoses

at the rated pressure or within the

 

and fittings before connecting the

rated pressure range as marked on

 

using the tool for the first time and

tool to an air supply. Replace any

the tool.. Always verify prior to using

before each use.. If an inline oiler is

damaged or worn hoses or fittings.

the tool that the air source has been

used, manual lubrication through the

Tool performance or durability may be

adjusted to the rated air pressure or

air inlet is not required on a daily basis..

reduced.

Service

within the rated air-pressure range..

 

The work surface

b.. Never use oxygen, carbon dioxide,

 

 

can become

 

a.. Tool service must be performed only

 

damaged by excessive lubrication.

combustible gases or any bottled

 

by qualified repair personnel.

 

Proper lubrication is the owner’s

gas as an air source for the tool.

 

 

responsibility. Failure to lubricate the

b.. When servicing a tool, use only

 

Such gases are capable of explosion

tool properly will dramatically shorten

identical replacement parts. Use

and serious injury to persons..

 

the life of the tool and void your

only authorized parts.

 

 

 

 

warranty.

 

 

 

 

 

 

 

 

c.. Use only the lubricants supplied

 

Do not use

 

1.

Disconnect the air

 

 

 

 

supply from the tool

 

with the tool or specified by the

any type of reactive gases,

O CO2

 

 

 

manufacturer.

including, but not limited to,

 

 

to add lubricant..

 

oxygen and combustible

 

 

 

 

 

Do not make any

 

 

 

 

 

gases, as a power source. Use filtered,

 

 

 

 

modifications to

 

2.

Turn the tool so the air

 

lubricated, regulated compressed air

 

 

the tool without first obtaining written

 

 

inlet is facing up.. Place

 

only. Use of a reactive gas instead of

 

 

OIL

approval from Campbell Hausfeld. Do

compressed air may cause the tool

 

 

4-5 drops of 30 W non-

 

not use the tool if any shields or guards

 

 

 

to explode which will cause death or

 

 

detergent oil into air inlet..

 

are removed or altered. Do not use the

 

 

 

serious personal injury.

 

 

 

 

 

 

 

Do not use detergent

 

tool as a hammer. Personal injury or

 

 

 

 

 

 

 

 

 

 

tool damage may occur.

 

 

 

 

 

oils, oil additives, or air- tool oils..

Disconnect air

Use only a pressure-regulated

 

 

Air tool oils contain solvents which

supply and release

 

 

will damage the tool's internal

compressed air source to limit the

 

 

tension from the pusher before

 

 

components..

 

pressure supplied to the

120 psi

 

 

attempting to clear jams because

 

 

 

 

 

tool. The regulated pressure must not

 

3. After adding oil, run

 

fasteners can be ejected from the front

 

 

of the tool. Personal injury may occur.

exceed 120 psi. If the regulator fails, the

 

tool briefly.. Wipe off

 

 

pressure delivered to the tool must not

 

any excess oil from

 

Air Source

exceed 200 psi. The tool could explode

 

 

 

 

 

the cap exhaust..

 

a.. Never connect to an air source that

which will cause death or serious

 

 

 

 

 

 

 

personal injury.

 

 

Recommended Hookup

 

is capable of exceeding 200 psi.

 

 

 

 

 

 

 

 

Save These Instructions

 

 

 

 

Over pressurizing the tool is able

 

The illustration below shows the

 

Do Not Discard

 

to result in bursting, abnormal

 

 

recommended hookup for the tool..

 

 

 

 

Recommended Hookup

 

 

 

 

 

 

 

 

 

 

Quick

Regulator

 

 

 

 

 

 

 

 

 

Quick

Quick Plug

Coupler

 

 

 

 

Quick Plug

Coupler

(Optional)

(Optional)

 

 

 

 

Air Hose

Lubricator

Filter

www.chpower.com

4