
Operating Instructions
Operating Instructions | 3. | Make sure the trigger | LOADINg the nailer | |||
(Continued) |
| and work contact | 1. | Always disconnect the tool from | ||
mode conversion |
| element (WCE) move |
| the air supply before loading | ||
| freely up and down |
| ||||
To convert the tool from one mode to |
|
| fasteners.. |
| ||
| without sticking or |
|
| |||
|
|
|
| |||
the other: |
| 2. | Pull nail pusher | Nail Pusher Latch | ||
| binding.. | |||||
1. | Remove |
|
| mechanism back | ||
|
|
| Mechanism | |||
|
|
| until pusher | |||
| pin.. |
|
|
|
| |
|
|
|
| engages with |
| |
2. | Remove trigger pin, trigger, and | 4. | Reconnect air supply |
|
| |
| magazine latch.. |
| ||||
| trigger spring.. |
| to the tool.. |
|
| |
|
|
|
|
| ||
3. Switch out only the trigger.. |
|
|
|
|
| |
4. Replace trigger spring, trigger, | 5. | Depress the Work | 3. | Load strips of |
| |
| trigger pin, and |
| fasteners into |
| ||
|
| Contact Element |
|
| ||
Do not attempt to modify the trigger |
|
| the magazine |
| ||
| (WCE) against |
|
| |||
|
| slot.. Make sure |
| |||
components in any manner and do |
| the work surface |
|
| ||
|
| that the nails are |
| |||
not attempt to use any other trigger |
| without pulling |
|
| ||
|
| placed into tool |
| |||
components other than those intended |
| the trigger.. The |
|
| ||
|
| at the proper |
| |||
for this tool.. |
| tool must not |
|
| ||
|
| orientation.. |
| |||
Contact your Campbell Hausfeld |
| operate.. Do not use the tool if it |
|
| ||
| 4. | Squeeze the |
| |||
representative if you have any |
| operates without pulling the trigger.. |
| |||
|
| pusher and the |
| |||
questions.. |
| Personal injury may result.. |
|
| ||
|
| latch together to |
| |||
|
| 6. | Remove the tool |
|
| |
Mode Conversion |
| unlatch pusher.. |
| |||
| from the work |
|
| |||
| Trigger spring |
|
| Make sure the |
| |
|
| surface.. The |
|
| ||
|
|
|
| head of the last |
| |
|
| Work Contact |
|
| ||
|
|
| nail is under the |
| ||
|
| Element (WCE) |
|
| ||
|
|
|
|
| ||
|
|
|
| head of the pusher.. | ||
| Trigger |
| must return |
| ||
|
|
|
|
| ||
|
| to its original | UNLOADING THE Nailer | |||
|
|
| ||||
|
|
| down position.. The tool must not | 1. Always unload all fasteners before | ||
|
|
| operate.. Do not use the tool if it | |||
|
|
|
| removing tool from service.. | ||
|
|
| operates while lifted from the work |
| ||
| Trigger pin |
|
| Unloading is the reverse of loading, | ||
|
| surface.. Personal injury may result.. |
| |||
|
|
| except always disconnect the air | |||
|
|
|
| |||
|
| 7. | Pull the trigger |
| hose before unloading.. | |
Operating A Sequential Trip Tool |
| and depress the | 2. | Pull nail pusher | Nail Pusher Latch | |
| Check the operation |
| work contact | |||
|
|
| mechanism back | Mechanism | ||
| of the Work Contact |
| element (WCE) |
| until pusher | |
|
|
|
| |||
Element (WCE) trip mechanism before |
| against the work surface.. The tool |
|
| ||
|
| engages with |
| |||
each use. The WCE must move freely |
| MUST NOT operate IF IN single |
|
| ||
|
| magazine latch.. |
| |||
without binding through its entire |
| cycle mode (black trigger).. The |
|
| ||
|
|
|
| |||
travel distance. The WCE spring must |
|
|
|
| ||
| tool MUST operate IF IN bottom |
|
|
| ||
return the WCE to its fully extended |
|
|
|
| ||
| trip mode (red trigger).. |
|
|
| ||
position after being depressed. Do |
| 3. | Hold tool upright |
| ||
not operate the tool if the WCE trip |
|
|
| |||
8. | Depress the |
| so nails will |
| ||
mechanism is not operating properly. |
|
| ||||
| Work Contact |
| slide backwards |
| ||
Personal injury may occur. |
|
|
| |||
| Element (WCE) |
| toward magazine |
| ||
1. | Disconnect the air |
|
|
| ||
| against the |
| slot.. |
| ||
| supply from the tool.. |
|
|
| ||
|
| work surface.. |
|
|
| |
|
|
|
|
|
| |
|
|
| Pull the trigger.. The tool MUST |
|
|
|
2. | Remove all fasteners |
| operate.. | 4. | Squeeze the |
|
| An improperly |
| pusher and |
| ||
| from the magazine |
| functioning tool |
| latch together |
|
| (see Loading / | must not be used. Do not actuate the |
| to unlatch the |
| |
| Unloading).. | tool unless the tool is placed firmly |
| pusher once all |
| |
| against the work piece. |
|
| |||
|
|
| nails have been |
| ||
|
|
|
|
|
| |
|
|
|
|
| removed.. |
|
www.chpower.com |
|
|
|
|
|
6