Operating Instructions

 

 

 

 

 

PN001000

Important Safety Instructions

 

 

 

 

 

use detergent oils, oil additives, or

(Continued)

Do not use any type of

 

O CO2

 

air- tool oils. Air tool oils contain

 

 

solvents which will damage the

Service

reactive gases, including, but

 

 

 

 

tool's internal components.

 

a.

Tool service must be performed only

not limited to, oxygen and

 

 

 

 

 

 

 

 

 

 

by qualified repair personnel.

combustible gases, as a power source.

3.

After adding oil, run

 

 

Use filtered, lubricated, regulated

 

tool briefly. Wipe off

 

b.

When servicing a tool, use only

 

 

compressed air only. Use of a reactive

 

 

 

any excess oil from

 

 

identical replacement parts. Use

gas instead of compressed air may

 

 

 

 

the cap exhaust.

 

 

only authorized parts.

cause the tool to explode which will

 

 

 

cause death or serious personal injury.

 

 

 

c. Use only the lubricants supplied

Recommended Hookup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

with the tool or specified by the

 

 

 

 

The illustration below shows the

 

 

manufacturer.

Use only a pressure-regulated

 

recommended hookup for the tool.

 

Do not make any

compressed air source to limit

125 psi

1.

The air compressor

50 psi

 

modifications to

the air pressure supplied to

 

 

 

must be able to

Min.

the tool without first obtaining written

the tool. The regulated pressure must

 

125 psi

 

maintain a minimum

approval from Campbell Hausfeld. Do

not exceed 125 psi. If the regulator

 

Max.

not use the tool if any shields or guards

fails, the pressure delivered to the

 

of 50 psi when the

 

are removed or altered. Do not use the

tool must not exceed 200 psi. The tool

 

tool is being used. An inadequate air

tool as a hammer. Personal injury or

could explode which will cause death or

 

supply can cause a loss of power and

tool damage may occur.

serious personal injury.

 

 

 

inconsistent driving.

 

 

 

 

Save These Instructions

 

 

Air Source

 

2.

An oiler can be

 

 

Do Not Discard

 

 

a. Never connect to an air source that

 

 

 

used to provide oil

 

 

 

 

 

 

 

 

is capable of exceeding 200 psi.

Operating Instructions

 

 

circulation through

 

 

Over pressurizing the tool is able

 

 

the tool. A filter can

 

 

 

 

 

 

 

 

 

to result in bursting, abnormal

Lubrication

 

 

 

be used to remove

 

 

operation, breakage of the tool or

This tool requires lubrication before

 

liquid and solid impurities which can

 

serious injury to persons. Use only

 

rust or “gum up” internal parts of

 

using the tool for the first time and

 

 

clean, dry, regulated compressed air

 

the tool.

 

 

before each use. If an inline oiler is

 

 

 

at the rated pressure or within the

3.

Always use air supply hoses with

 

used, manual lubrication through the

 

rated pressure range as marked on

 

a minimum working pressure

 

 

air inlet is not required on a daily basis.

 

 

 

the tool. Always verify prior to using

 

rating equal to or greater than the

 

 

The work surface

 

 

the tool that the air source has been

 

 

pressure from the power source if a

 

 

can become

 

 

 

adjusted to the rated air pressure or

damaged by excessive lubrication.

 

regulator fails, or 150 psi, whichever

 

within the rated air-pressure range.

Proper lubrication is the owner’s

 

is greater. Use 1/4 inch air hose for

b. Never use oxygen, carbon dioxide,

responsibility. Failure to lubricate the

 

runs up to 50 feet. Use 3/8 inch or

tool properly will dramatically shorten

 

 

combustible gases or any bottled

 

greater air hoses for 50 foot run or

 

the life of the tool and void your

 

 

gas as an air source for the tool.

 

longer.

 

 

warranty.

 

 

 

 

 

Such gases are capable of explosion

1.

Disconnect the

 

 

 

 

 

 

and serious injury to persons.

 

 

 

150 psi or greater

 

 

 

air supply from

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the tool to

 

 

4. Use a pressure regulator on the

 

 

 

add lubricant.

 

 

 

 

 

 

 

 

compressor, with an operating

 

 

 

 

 

 

 

 

 

2. Turn the tool so the

 

 

 

pressure of 0 psi - 125 psi. A pressure

 

 

 

air inlet is facing up.

OIL

 

 

regulator is required to control

 

 

 

Place 4-5 drops of 30

 

 

 

the operating pressure of the tool

 

 

 

W non-detergent oil

 

 

 

between 50 psi and 125 psi.

 

 

 

 

into air inlet. Do not

 

 

 

 

 

Minimum Recommended Hookup

 

 

 

 

 

 

 

Quick

 

 

 

 

 

 

 

 

Quick Plug Coupler

Quick Plug

 

 

 

 

 

Quick

Coupler

Air Hose

www.chpower.com

4