Assembly Instructions and Parts List | PW158010AV |
Instrucciones de Montaje y Lista de Piezas | PW158010AV |
Garden Hose Connection
GARDEN HOSE CONNECTION INSTRUCTIONS
1.Attach nipple adapter to inlet fitting on the unit (this may already be attached to the pump).
2.Attach quick connect fitting to garden hose.
3.Pull side “A” of quick connect fitting toward garden hose and push onto nipple adapter.
4.Push side “A” of quick connect fitting towards nipple adapter and release.
"A"
Quick Connect Fitting
Garden Hose
Nipple
Adapter
! IMPORTANT !
This pressure washer is equipped with a microswitch sensitive to water flow. This Instant Start/Stop switch (ISS) senses water flow in the pump. When the trig- ger is released, water stops flowing through the pump. The ISS then auto- matically turns the motor off to protect pump from overheating.
OPERATION
1.Pull trigger on gun.
2.Turn the “ON/OFF” switch to “ON”.
3.Release trigger. The pressure washer motor will stop running.
4.To spray again, pull trigger and motor and pump will restart.
Note: Occasionally the motor may run for a short time to bring fresh, cool water into the pump even if trigger is released. This is part of normal opera- tion and will not damage the unit.
Cable de Corriente Eléctrica Continuación
2.SE DEBE HACER ESTO CADA VEZ QUE LA UNIDAD SE ENCHUFE EN UN TOMACOR- RIENTE.
System Connection
1.Inserte la lanza en la pistola y gírela en el sentido de las agujas del reloj hasta que llegue a su tope, como se muestra en la Figura 4.
Figura 4 - Conexión de la pistola y lanza
2.Verifique que el interruptor de energía esté en la posición "OFF" ("APAGADO").
3.Conecte la manguera de alta presión y el conjunto de pistola en la unidad.
4.Conecte la manguera de jardín según se explica en Instrucciones de conex- ión de la manguera de jardín.
5.Enchufe el cordón de corriente en un tomacorrientes de 120 V con conex- ión a tierra, que se encuentre en un circuito dedicado.
6.Abra la llave del agua.
7.Presione el gatillo y manténgalo pre- sionado por 1 minuto para liberar la presión y remover el aire atrapado en el sistema.
8.Mueva el interruptor "ON/OFF" (“ENCENDIDO/APAGADO”) a la posi- ción "ON" ("ENCENDIDO").
NOTA: PARA OBTENER INSTRUC- CIONES DE OPERACIÓN, CONSULTE EL MANUAL DEL PRODUCTO.
Figure 2 - Garden Hose Connection
Power Cord
1.Plug the power cord into a grounded 120V outlet and press the reset button as shown in Figure 3.
2.THIS MUST BE DONE EACH TIME THE UNIT IS PLUGGED IN AN OUTLET.
Reset
Figure 3 - Grounded plug/reset button
Always turn the
!CAUTION “ON/OFF” switch to “OFF” then trigger gun to release hose pres- sure before unplugging power cord.
Risk of equipment dam-
!CAUTION age. Always make sure the “ON/OFF” switch on the unit is “OFF” and unit is unplugged prior to storage.
Risk of Injection.
Unit will start spraying
when trigger is squeezed if on/off switch is in “ON” position. Always point gun in safe direction.
Call
Interruptor | Pistola |
"On/Off" |
|
(Encendido/ |
|
Apagado) |
|
SALIDA |
|
13 mm |
|
| Manguera de |
| alta presión |
| ENTRADAINLET |
Manguera |
|
de jardín |
|
Figura 5
www.chpower.com | 2 | 11 Sp |
|
|
