Q T 5 0 1 4 4 V 0 2

 

Start Here

 

series

 

 

 

 

 

 

Easy Setup Instructions

 

Photo Printer

 

 

 

 

1 Unpack the Printer

2 Prepare the Printer

3 Install the Print Head

4 Install the Ink Tanks

Connect the Printer

5 and Load Paper
1Carefully remove all items from the box.

PIXMA Pro9500 series

Photo Printer

Documentation and

Software Kit

1Plug the power cord into the back of the printer and connect the other end to a power outlet. Press the POWER button. The printer will initialize. Wait until the POWER lamp displays a steady blue light.

POWER Lamp

POWER Button

2Open the Front Tray. Raise the Top Cover.

NOTE: Gently press the mark on the Front Tray. The Front Tray automatically opens.

Top Cover

1Firmly raise the print head lock lever.2Remove the Print Head from its package.

Nozzles

Tear at notch to open

CAUTION: There might be some transparent or light color ink on the inside of the bag the Print Head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.

NOTE: Do not touch the nozzles.3Remove and discard the orange protective cap from the Print Head.
1Remove the Red Ink Tank (PGI-9R) from its package.

2Remove and discard the orange protective cap located on the bottom of the ink tank.

IMPORTANT: Do not touch the electrical contacts.

NOTE:

·To avoid spilling ink, never press on the sides of an ink tank.

·Do not touch the open ink port once the protective cap is removed, as this may prevent the ink from being ejected properly.

Electrical Contacts

Protective Cap

Ink Port

3Insert the ink tank into the rightmost slot.

Press the mark on the ink tank until it clicks into place and then its lamp lights red.

IMPORTANT: When the POWER lamp flashes blue and the printer vibrates, the printer is shaking the ink tanks. Once you have installed the ink tanks and have closed the Top Cover, wait for about 2 minutes 30 seconds until the POWER lamp stops flashing and stays lit, and the printer has stopped making operating noises before proceeding. Do not open the Top Cover while the printer is operating (the POWER lamp is flashing blue).

1TURN THE PRINTER OFF.

IMPORTANT: Be sure the printer is off before continuing, or the computer will attempt to install the printer driver before the printer is ready.

2Connect one end of the USB cable to the computer, the other to the appropriate USB port on the printer.

NOTE: The Pro9500 series Photo Printer is equipped with USB 2.0 Hi-Speed port. If your PC does not support USB 2.0 Hi-Speed, or if any non-certified USB 2.0 cable or driver is used for the connection, the printer will operate at a lower speed provided under USB 1.1.

USB Port

USB Port USB Cable

PIXMA Pro9500 series

Print Head

Power Cord

Front Tray

3The Print Head Holder automatically moves to the center. Remove the protective tape from the Print Head Holder. The tape position is subject to change.

CAUTION: There might be some transparent or light color ink on the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.

NOTE:

·Do not touch the print head nozzles and the electrical contacts.·Do not attempt to reattach the protective cap once it has been removed.

Print Head

Electrical

Contacts

Nozzles

 

click

Ink Lamp

4Insert the remaining nine ink tanks into their assigned slots. Ensure that ink lamps light red.

Refer to the color guide on the print head lock lever.

5 Close the Top Cover. Lift open the Paper
Support and the Paper Support Extension, then
pull out the Front Tray Extension.

USB Cable

3Pinch the Paper Guide and slide it to the left. Load two sheets of plain paper into the Auto Sheet Feeder, align the paper with the right edge of the Auto Sheet Feeder, then slide the Paper Guide toward the left edge of the paper.

Auto Sheet

 

 

PGI-9MBK

 

 

 

PGI-9PBK

Matte

PGI-9PC

 

 

Black

 

PGI-9PM

Photo

Photo

PGI-9GY

 

Photo

Black

 

Cyan

Gray

Magenta

 

 

 

 

Protective Tape

4Write down the serial number located inside the printer. You will need this to register your products.

4Slide the Print Head into the holder. The Print Head will rest at a slight angle.

Paper Support

Extension

Paper Support

Top Cover

Feeder

Paper

Guide

Print Side

 

PGI-9C

 

PGI-9Y

Cyan

PGI-9G

PGI-9M Yellow

 

Green PGI-9R

Magenta

 

Red

2Remove the tapes from the printer.

NOTE:

·It takes about an hour to complete the setup of the printer.·A USB cable is necessary to connect the printer with your computer.

Electrical

Contacts

NOTE: Do not touch the electrical contacts.5 Lower the print head lock lever carefully.

Serial Number Location

IMPORTANT: If the Top Cover is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Top Cover to return the holder to the center.

Front Tray Extension

NOTE: If the ALARM lamp on the printer flashes orange after you have closed the Top Cover, an ink tank may not be installed properly. Open the Top Cover and make sure that the ink tanks are installed in the correct order directed on the label.

IMPORTANT: Print Head Alignment (Step 6) requires that letter size paper is loaded in the Auto Sheet Feeder (top paper feeder).

Continue with Step 6 on the back page.