☞Continued from front side

10.Read the software license agreement, and click [Yes] if you consent to its conditions.

11.Confirm the installation destination, and click [Next].
Installation of CapturePerfect 3.0 starts.
12.Click [Finish] to complete the installation of CapturePerfect 3.0.
Next, the installation wizard for the User Manual appears.
13.Click [Next].
Installation of the User Manual starts.
14.Click [Finish] to complete the installation of the User Manual.

15.When all installations are complete, the installation completed screen appears.

Click [Exit] to exit the installer. Click [Back] to return to the menu screen.
This completes the software installation.
Next, you need to connect the scanner to your computer. (☞ STEP 4)

Connecting the Scanner to the

Computer

There are two methods for connecting the DR-X10C scanner to a computer: a USB connection to a standard USB port built in to the computer, or SCSI connection to a SCSI card installed in an expansion slot of the computer. Select the method that is best suited to your computer environment.

USB Connector

SCSI Connector (D-sub, 50-pin half-pitch)

DIP Switches for SCSI ID

Power Connector

CAUTION

❏Do not connect both USB and SCSI cables to the scanner at the same time.
❏Use only the supplied power cord.
❏The scanner and computer should both be turned OFF when making connections.

❏Make sure that the computer is turned OFF before connecting the SCSI cable. The scanner may not be properly recognized by the computer if it is connected while the computer is turned ON.

❏A SCSI cable is not supplied with the scanner. Obtain a cable with connectors that match the SCSI connectors on both the scanner and the computer.

Connecting the Power Cord

1.Connect the supplied power cord into the power connector on the back of the scanner. (1)

2.Connect the power cord into an AC outlet. (2)
When Connecting by USB

3.Use the supplied USB cable to connect the scanner to the computer. Connect the square plug (Type B) of the USB cable to the scanner.

Type A

Type B

When Connecting by SCSI
3.Use the SCSI cable to connect the scanner to the computer.

A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner.

CAUTION

❏Observe the following when connecting the scanner with other devices in a “daisy chain”.

•The SCSI ID of the scanner is set to “SCSI ID = 2” by default. When using a daisy-chain configuration with other SCSI devices, set the DIP switches so that SCSI ID numbers are not duplicated in the system.

DIP Switches

Default Position (SCSI ID=2)

•The DR-X10C scanner incorporates a SCSI terminator which is permanently set to ON. When using a daisy-chain configuration with other SCSI devices, make sure that the DR-X10C scanner is connected as the last device in the chain. Set the terminators of all other devices to OFF.

The scanner is now connected to your computer.

Next, you need to turn on the scanner and ensure Windows recognizes it. (☞ STEP 5)

Turning the Power ON (Scanner

Recognition)

When you turn ON the computer and the scanner, the Windows Plug and Play function recognizes the scanner and automatically installs the required device driver.

CAUTION

❏When connecting the scanner to the computer using a SCSI cable, be sure to turn ON the scanner first, and then turn ON the computer. If you turn ON the computer first, the scanner may not be properly recognized by the computer.

❏Be sure to log on to Windows using an account with Administrator privileges.

❏After turning the scanner OFF, wait at least 10 seconds before turning it ON again.

❏If you will not be using the scanner for an extended period, disconnect the power cord from the AC outlet for safety.

1.Make sure that the scanner and computer are connected properly.

2.Press the power switch to turn the scanner ON. The Document Feed Tray opens automatically.

Power Switch
3.Turn ON the computer.

4.Windows automatically recognizes the scanner and performs the device driver installation.

Windows 2000

Windows XP

Windows Vista

IMPORTANT

●With Windows Vista, installation proceeds automatically regardless of the displayed “Check here for status” balloon help.

You can click “Check here for status” to display the installation progress.

●With Windows XP and Vista, a message appears when installation is finished. Windows XP

Windows Vista

●The DR-X10C device driver is installed in Device Manager under [Imaging Devices] as [CANON DR-X10C USB] or [CANON DR-X10C SCSI].

●From the Control Panel, you can display the Device Manager using the following procedure:

–With Windows 2000, open [System] and click [Device Manager] on the Hardware tab sheet.

–With Windows XP, first switch the Control Panel to the Classic View to display [System]. Then open [System] and click [Device Manager] on the Hardware tab sheet.

–With Windows Vista, open [System Maintenance] and click [Device Manager]. Or, switch the Control Panel to the Classic View and click the [Device Manager] icon.

●By enabling the User Mode function for Auto USB Power Switch, you can have the computer’s power switch turn the scanner ON and OFF. For details on User Mode and USB-linked power switching, refer to the User Manual.

<USB-linked power switch>

Turning the computer ON or OFF turns the scanner ON (document feed tray opens) or OFF.

The computer should now recognize the scanner properly.
Next, you need to select the scanner from your application program. (☞ STEP 6)

Selecting the Scanner

To use the scanner with an ISIS/TWAIN-compliant application program, the scanner must first be selected.

The menus and procedures used for selecting scanners vary depending on the application used. For detailed information on selecting scanners, refer to the user’s manual for your application.

This section describes how to select the scanner when using CapturePerfect 3.0. For details on how to use CapturePerfect 3.0, refer to CapturePerfect 3.0 Operation Guide located in the Windows program menu.

1.Launch CapturePerfect 3.0 from the Windows program menu.
CapturePerfect3.0
2.From the [Scan] menu, select [Select Scanner].
The [Select Scanner] dialog box appears.
3.Select [CANON DR-X10C], and click [Settings].
The [Configure Device Settings] dialog box appears.
4.Set the default page size.
5.Click [OK] to finish scanner selection.

The setup is now complete

●This completes the setup of the DR-X10C. Before you start using the scanner, make sure to thoroughly read the Reference Guide or the User Manual.

●For details on how to use CapturePerfect 3.0, refer to CapturePerfect 3.0 Operation Guide located in the Windows program menu.