|
| Start Here |
|
|
|
| Easy Setup Instructions |
|
|
|
|
| ||
| Unpack the Machine | • Please confirm the included items against the illustration printed on the lid of the packing box. |
| |
| • A USB cable is necessary to connect the machine with your computer. |
|
| |
|
|
|
| |
| 2 Install the Print Head | |||
1 Prepare the Machine |
3Install the Ink Tanks
Photo All-in-One
4Align the Print Head
a Place the machine on a flat and horizontal surface, and do not place any objects in front of the machine. Open the Sheet Feeder Cover and pull the Paper Support, then the Paper Output Tray and open the Output Tray Extension.
Caution Before turning on the machine, remove all of the shipping tapes.Important Do not connect the USB cable until after the software is installed.Note To open the Paper Output Tray, put your finger in the rounded indent of the tray and open it gently.
b Plug the power cord in the back of the machine and connect the other end to the wall outlet.
d Use the { or } button on the Operation Panel to select the language for the LCD, then press the OK button.
(1)Press the { or } button to select the language.
(2)Press the OK
button.
Important If an unintended language is displayed on the LCD, press the Back button to return to the Language selection screen.
Once the message “Install the print head and set the ink tank.” appears, go to e.
e Open the Scanning Unit (Printer Cover) until it locks into place. The Print Head Holder moves to the center.
a Remove the Print Head from its package.
Caution There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.
b Remove the orange protective cap from the Print Head and discard it.
Electrical Contacts
Protective Cap | Print Head Nozzles |
Note |
|
Do not touch the print head nozzles or the electrical | |
contacts. |
|
c Firmly raise the Print Head Lock Lever | |
until it stops.The Print Head Lock Lever | |
may feel heavy. |
|
a Peel back the orange tab completely and remove the plastic wrapper from the ink tank.
If the
b Twist off and discard the orange protective cap located on the bottom of the ink tank.
Protective Cap Do not press!
Ink Port
Electrical Contacts
Important•Do not touch the electrical contacts.•Do not touch the ink port.c Insert the ink tank into the | |
slot and press the | mark on the ink |
tank until it clicks into place. |
a Pinch the Paper Guide and slide it to the left end.
Paper Support
Extension
Paper Guide
b Load a sheet of letter- or
Paper Guide
Print Side
Hardware setup and Print Head alignment is complete.
Scanning Unit (Printer Cover)
Cover Guide
c Make sure that Yes is selected in the message requesting head alignment,
Easy-Scroll Wheel
Turn the
c Open the Operation Panel, then press the ON/OFF button to turn on the machine.
Important For your safety, always firmly grip the areas illustrated when opening the Scanning Unit (Printer Cover).
f Open the Inner Cover. Write down the serial number located inside the machine. You will need this to register your product.
d Insert the Print Head.
Do not touch!
e Lower the Print Head Lock Lever carefully.
d Make sure the ink lamp lights red.
Refer to the color guide on the Print Head Lock Lever.
e Close the Inner Cover and the Scanning Unit (Printer Cover).
then press the OK button.
For details, refer to “Basic Operation for the Operation Panel” in the Quick Start Guide.
*You can also use the {, }, [, or ] button to select.Note Print Head alignment takes about 6 minutes to complete. Do not start another operation here.
The pattern is printed. And Print Head is aligned automatically.OK
Cassette
Inner Cover Serial Number Location | Important |
| If the Scanning Unit (Printer Cover) is left open |
| for more than 10 minutes, the Print Head Holder |
| moves to the right. Close and reopen the Scanning |
| Unit (Printer Cover) to return the Holder to the |
| center. |
Important
•For your safety, always firmly grip the areas il- lustrated when closing the Scanning Unit (Printer Cover).
•The machine starts operating. Wait about 2 min- utes until the machine stops making noise.
Note
•The pattern is printed in black and blue.•When Automatic Print Head Alignment cannot be executed correctly, the message “Auto head align has failed.” is displayed on the LCD. Refer to “Error Message is Displayed on the LCD” in the User’s Guide