Start Here

Easy Setup Instructions

 

 

Unpack the Machine

• Please confi rm the included items against the illustration printed on the lid of the packing box.

 

 

 

 

 

 

 

 

 

 

• A USB cable is necessary to connect the machine with your computer.

 

 

 

 

 

 

 

 

 

 

 

 

QT5-0786-V01

 

 

2 Install the Print Head

 

3 Install the Ink Tanks

1 Prepare the Machine

 

 

 

 

 

 

 

 

 

 

 

Office All-In-One

4Align the Print Head

a Place the machine on a fl at and horizontal surface, and do not place any objects in front of the machine. Open the Sheet Feeder Cover and pull the Paper Support, then the Paper Output Tray and open the Output Tray Extension.

Caution

e Use the { or } button on the Operation Panel to select the language for the LCD, then press the OK button.

a Remove the Print Head from its

a Peel back the orange tab completely

package.

and remove the plastic wrapper from

 

the ink tank.

a Pinch the Paper Guide and slide it to the left end.

Paper SupportExtension
Hardware setup and Print Head alignment is complete.
Before turning on the machine, remove all of the shipping tapes. ImportantDo not connect the USB cable until after the software is installed. Note
(1)Press the { or } button to select the language.(2)Press the OK button.

Caution

There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.

If the orange-colored protective fi lm is not removed completely, problems with printing may occur.

b Twist off and discard the orange protective cap located on the bottom of the ink tank.

Paper Guide

To open the Paper Output Tray, put your fi nger in the rounded indent of the tray and open it gently.

Important

If an unintended language is displayed on the LCD, press the Back button to return to the Language selection screen.

b Remove the orange protective cap from the Print Head and discard it.

Electrical Contacts
Do not press!
Protective CapInk Port

b Load two sheets of supplied paper

b Unlock the Scanning Unit (Printer Cover).

(1)Open the Document Cover.

(2)Move the Scanner Lock Switch towards the release mark to unlock the Scanning Unit (Printer Cover).

Caution

●Make sure to unlock the Scanning Unit (Printer Cover) before turning the machine on.

●Before transporting the machine, always lock the Scanning Unit (Printer Cover) by moving the Scanner Lock Switch towards the lock mark.

(2)(1)

Scanning Unit (Printer Cover)

c Plug the power cord in the back of the machine and connect the other end to the wall outlet.

Important

Make sure that the Document Cover is closed.

d Open the Operation Panel, then press the ON/OFF button to turn on the machine.

Once the message “Install the print head and set the ink tank.” appears, go to f.

f Open the Scanning Unit (Printer Cover) until it locks into place. The Print Head Holder moves to the center.

Important

●For your safety, always firmly grip the areas illus- trated when opening the Scanning Unit (Printer Cover).

●If the Document Cover is opened, you cannot open the Scanner Unit (Printer Cover). Be sure to open the Scanner Unit (Printer Cover) and the Document Cover at the same time.

g Open the Inner Cover. Write down the serial number located inside the machine. You will need this to register your product.

Inner Cover Serial Number Location

Protective Cap

Print Head Nozzles

Note

Do not touch the print head nozzles and the electrical contacts.

c Firmly raise the Print Head Lock Lever until it stops.The Print Head Lock Lever may feel heavy.

d Insert the Print Head.

Do not touch!

e Push the Print Head to hold it in place, and lower the Print Head Lock Lever.

Important

If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center.

Electrical Contacts

Important

•Do not touch the electrical contacts.•Do not touch the ink port.

c Insert the ink tank into the right-hand slot and press the mark on the ink tank until it clicks into place.

d Make sure the ink lamp lights red.

Refer to the color guide on the Print Head Lock Lever.

e Close the Inner Cover and the Scanning Unit (Printer Cover).

Important

•For your safety, always firmly grip the areas il- lustrated when closing the Scanning Unit (Printer Cover).

•The machine starts operating. Wait about 2 min- utes until the machine stops making noise.

(MP-101) into the Auto Sheet Feeder with the printing side (whiter side) facing up, align the paper with the right side of the Cover Guide, then slide the Paper Guide against the paper stack.

Paper Guide

Print Side
Cover Guide

c Make sure that Yes is selected in the message requesting head alignment, then press the OK button.

Note

Print Head alignment takes about 14 minutes to complete. Do not start another operation here.

The pattern is printed. And Print Head is aligned automatically.

OK

Note

•The pattern is printed in black and blue.

•When Automatic Print Head Alignment cannot be executed correctly, the message “Auto head align has failed.” is displayed on the LCD. Refer to “Error Message is Displayed on the LCD” in the User’s Guide on-screen manual.

Easy-Scroll Wheel

Turn the Easy-Scroll Wheel left or right to easily select a menu or a setting item. For details, refer to “Basic Operation for the Operation Panel” in the Quick Start Guide.

*You can also use the {, }, [, or ] button to select.

Cassette

For information on how to load paper in the Cassette, refer to “Loading Paper in the Cassette” in “Loading Printing Paper” of the Quick Start Guide.