2169/2299-2

Mode indicator

Minutes

Seconds

1/100 second

STOPWATCH MODE

The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. You also get Auto-Start function. The range of the stopwatch is 59 minutes, 59.99 seconds.

•In the Stopwatch Mode, press B to illuminate the display for about three seconds.

To measure elapsed time

1.Press E to start the stopwatch.

2.Press E to stop the stopwatch.

•You can resume the measurement operation by pressing E again. 3. Press D to clear the stopwatch to all zeros.

Mode indicator – Alarm No. Graphic area

Hour : Minutes

Alarm on indicator

ALARM MODE

You can set five independent Daily Alarms. When a Daily Alarm is turned on, the watch beeps for 20 seconds at the alarm time each day. Press any button to stop the alarm after it starts to sound.

When the Hourly Time Signal is turned on, the watch beeps every hour on the hour.

•In the Alarm Mode (including alarm time setting), press E to illu- minate the display for about three seconds.

•The graphic area in the Alarm Mode shows the current on/off sta- tus of each of the five alarms.

To record split times

1.Press E to start the stopwatch.

2.Press D to display the timing up to that point. Stopwatch timing continues internally.

3.Press D to clear the split time and to continue time measurement on the display.

•You can repeat steps 2 and 3 as many times as you want. 4. Press E to stop the time measurement.

5. Press D to clear the stopwatch to all zeros.

To time first and second place finishes

1.Press E to start the stopwatch.

2.Press D when the first finisher crosses the line, and record the time.

3.Press E when the second finisher crosses the line.

4.Press D to display the finishing time of the second finisher.

5.Press D again to clear the stopwatch to all zeros.

About the Auto-Start function

With the Auto-Start function, the watch performs a 5-second countdown. When the countdown reaches zero, stopwatch operation starts automatically. During the final three seconds of the countdown, a beeper sounds with each second.

To use the Auto-Start function

1.While the stopwatch display is showing all zeros (00'00"00) in the Stopwatch Mode, press D.

• At this time the auto-start indicator appears on the display to indicate that auto-start is on. Press D again to turn auto-start off (in- dicated when the auto-start indicator is not on the display).

2. Press E to start the countdown.

AM indicator

To set an alarm time

1.Press D while in the Alarm Mode to select the alarm whose time you want to set.

Alarm 1 Alarm 2 Alarm 3 Alarm 4

 

Hourly Time Signal

 

 

Alarm 5

 

 

 

2. After you select an alarm, hold down A until the hour digits start to flash on the display. The hour digits flash because they are selected.

•This operation automatically turns on the alarm.

3.Press C to change the selection in the following sequence.

Hour Minutes

4.Press D to increase the selected digits. Holding down D changes the selection at high speed.

•The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (A indicator) or p.m. (P indicator).

5. After you set the alarm time, press A to return to the Alarm Mode.

•If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Alarm Mode automatically.

To turn an alarm and the Hourly Time Signal on and off

•Pressing E also causes the countdown time to appear on the display.

Auto-start indicator

•When the countdown reaches zero, a tone sounds, the backlight illuminates the display, and a stopwatch timing operation starts automatically.

•To stop the Auto-Start countdown and return to the all-zeros display, press D.

•Pressing E while the Auto-Start countdown is in progress immediately starts the stopwatch.

Graphic area

Alarm on indicator

Alarm 5 (off)

Alarm 2 (off)

Alarm 1 (on)

Alarm 3 (on)

Alarm 4 (off)

1.In the Alarm Mode, press D to select an alarm or the Hourly Time Signal.

2.Press B to toggle the select item on and off.

• The indicators ALM and

appear on the display whenever

an alarm is turned on.

 

• The indicators SIG and

appear on the display whenever

the Hourly Time Signal is turned on.

•Indicators in the graphic area of the Alarm Mode show which alarms are turned on.

•In other modes (besides the Alarm Mode), the ALM indicator remains on the display as long as at least one of the alarms is on, while the SIG indicator remains on the display while the Hourly Time Signal is on.

To test the alarm

Hold down B while in the Alarm Mode to sound the alarm.