2358-2

4.When the character you want is at the cursor position, press Cto move the cursor to the right.

5.Repeat steps 3 and 4 until the name is complete.

•You can input up to eight characters for the name.

6.After you input the name, press C as many times as necessary to move the cursor to the number area.

•You can input up to eight characters for the name. When the cursor is located at the eighth space of the name, moving the cursor to the right causes it to jump to

the first digit of the number. When the cursor is at the 12th digit of the number, moving it to the right (by pressing C) causes it to jump to the first character in the name.

7.Use Band D to change the character (hyphen, number, or space) at the cursor position in the number area. The character changes in the following sequence.

Press .

to(space)

Press .

8.When the character you want is at the cursor position, press Cto move the cursor to the right.

9.Repeat steps 7 and 8 until you complete number input.

•You can input up to 12 digits for the number.

•The number initially contains all hyphens. You can leave the hyphens or replace them with numbers or spaces.

10.Press Ato store your data and return to the Telememo record screen (without the cursor).

• When you press Ato store data, the message may appear on the display for a while, indicating that data is being sorted. After the sort operation is complete, the Telememo record screen appears.

Hourly time signal on indicator

Timekeeping Mode time

Alarm time

Alarm on indicator

To set the alarm time

ALARM

You can set a Daily Alarm. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.

•The alarm and Hourly Time Signal operate in accordance with the current digital time (Timekeeping Mode time).

•All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.

1.In the Alarm Mode, hold down Auntil the hour digits of the alarm time start to flash.

•This automatically turns on the alarm.

2.Press Cto move the flashing between the hour and minutes.

3.While a setting is flashing, use D(+) to change it.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator).

4.Press Ato return to the alarm display screen.

To recall Telememo records

In the Telememo Mode, use D(+) and B(–) to scroll through Telememo records on the display.

To edit a Telememo record

1.In the Telememo Mode, scroll through the records and display the one you want to edit.

2.Hold down Auntil the flashing cursor appears on the display.

3.Use Cto move the flashing to the character you want to change.

4.Use Band D to change the character.

•For details on inputting characters, see “To create a new Telememo record” (step 3 for name input and 7 for number input).

5.After making the changes that you want, press Ato store them and return to the Telememo record screen.

To delete a Telememo record

1.In the Telememo Mode, scroll through the records and display the one you want to delete.

2.Hold down Auntil the flashing cursor appears on the display.

3.Press Band Dat the same time to delete the record.

• The message appears to indicate that the record is being deleted. After the record is deleted, the cursor appears on the display, ready for input.

4. Input data or press Ato return to the Telememo record screen.

Daily Alarm Operation

The alarm sounds at the preset time each day for about 20 seconds, or until you stop it by pressing any button.

•The alarm and hourly time signal sound in all modes.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn the Daily Alarm and Hourly Time Signal on and off

In the Alarm Mode, press Bto cycle through the on and off settings as shown below.

Alarm On Indicator/Hourly Time Signal On Indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Alarm On

 

 

Alarm Off

 

 

Alarm On

 

 

Alarm Off

 

 

Signal On

 

 

Signal Off

 

 

Signal Off

 

 

Signal On

 

 

 

 

 

 

 

 

 

 

 

 

 

STOPWATCH

WORLD TIME

1/100 second

The stopwatch lets you measure elapsed time, split times, and two finishes.

•

The display range of the stopwatch is 23 hours, 59

•

minutes, 59.99 seconds.

The stopwatch continues to run, restarting from zero

 

after it reaches its limit, until you stop it.

GMT differential

World map

World Time shows the current time in 27 cities (29 time zones) around the world.

•For full information on city codes, see the “CITY CODE TABLE”.

•The time zone that corresponds to the selected city code flashes on the world map.

•All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.

To view the time in another city code

Hours Seconds

Minutes

•

The stopwatch measurement operation continues even

•

if you exit the Stopwatch Mode.

All of the operations in this section are performed in the

•

Stopwatch Mode, which you enter by pressing C.

The time on the screen may not appear to stop

 

immediately when you press the button to stop an

 

elapsed time operation or perform a split time operation

 

in the Stopwatch Mode. Despite this, the time recorded

 

by your button operation is accurate.

City code

Current time in the selected city code

While in the World Time Mode, press Dto scroll forward through the city codes (time zones) and Bto scroll back.

•If the current time shown for a city is wrong, check your Timekeeping Mode time and Home City code settings and make the necessary changes.

To measure times with the stopwatch

Elapsed Time

Start

Stop

Re-start

Stop

Clear

Split Time

To toggle a city code time between standard time and Daylight Saving Time

1. In the World Time Mode, use Band Dto display the city code (time zone) whose standard time/Daylight Saving Time setting you want to change.

2. Hold down Afor about two seconds to toggle Daylight Saving Time (DST displayed) and standard time (DST not displayed).

• The DST indicator is on the display whenever you display a city code for which Daylight Saving Time is turned on.

•Note that the DST/Standard Time setting affects only the currently displayed city code. Other city codes are not affected.

•Note that you cannot switch between standard time

and Daylight Saving Time while

is selected as

the city code.

 

Start

Split

Split release

Stop

Clear

Two Finishes

Start

Split

Stop

Split release

Clear

 

First runner

Second runner

Record time of

 

 

finishes.

finishes.

second runner.

 

 

 

Record time of

 

 

 

 

first runner.