USER’S GUIDE 2611
To use the countdown timer
In the Countdown Timer Mode, press D to start the countdown timer.
• The countdown timer measurement operation continues even if you exit the Countdown Timer Mode.
• The table below describes button operations you can perform to control countdown operations.
To do this: | Do this: |
Stop the countdown operation | Press D. |
|
|
Resume a stopped countdown operation | Press D again. |
|
|
Display the countdown start time | While the countdown is |
| stopped, press B. |
|
|
Stop the countdown operation and display the reset time | Press B. |
|
|
Start the countdown from the displayed reset time | Press D. |
|
|
• The table below describes button operations you can perform during an elapsed |
time measurement operation in the elapsed time mode. |
•The snooze alarm on indicator () flashes during the
•Displaying the Alarm 1 setting screen while the snooze alarm is turned on automatically turns off the snooze alarm (making Alarm 1 a
To turn the hourly time signal on and off
1.In the Alarm Mode, use D to select the Hourly Time Signal.
2. Press B to toggle it on and off.
• Turning on the Hourly Time Signal displays the hourly time signal on indicator () on its screen.
• The hourly time signal on indicator is displayed in all modes.
Hourly time signal on indicator
Stopwatch
To do this: | Do this: |
|
|
Stop the elapsed time operation | Press D. |
|
|
Resume a stopped elapsed time operation | Press D again. |
|
|
Display the countdown start time | While the elapsed time is |
| stopped, press B. |
|
|
Stop the elapsed time operation and display the reset time | Press B. |
|
|
Start the countdown from the displayed reset time | Press D. |
|
|
Alarms
Minutes
Seconds
1/100 Second
The stopwatch lets you measure elapsed time, split times, and two finishes.
•The display range of the stopwatch is 59 minutes, 59.99 seconds.
•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.
•Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.
•All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.
Alarm time (Hour : Minutes)
Alarm number
SNZTo set an alarm time
You can set five independent Daily Alarms. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. One of the alarms can be configured as a snooze alarm or a
You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.
•There are five alarm screens numbered 1 through 5. The hourly time signal screen is indicated by :00.
•When you enter the Alarm Mode, the screen you were viewing when you last exited the mode appears first.
•All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.
1.In the Alarm Mode, use D to scroll through the alarm screens until the one whose time you want to set is displayed.
To measure times with the stopwatch
Elapsed Time
D | ➤D | ➤D | ➤D | ➤B |
Start | Stop |
| Stop | Clear |
Split Time |
|
|
|
|
D | ➤B | ➤B | ➤D | ➤B |
Start | Split | Split release | Stop | Clear |
| (SPL displayed) |
|
|
|
Two Finishes |
|
|
|
|
D | ➤B | ➤D | ➤B | ➤B |
Start | Split | Stop | Split release | Clear |
| First runner | Second runner | Display time of |
|
| finishes. | finishes. | second runner. |
|
| Display time of |
|
|
|
| first runner. |
|
|
|
x1 x2 x3
Backlight
:00 x5 x4
•You can configure Alarm 1 as a snooze alarm or a
•The snooze alarm repeats every five minutes.
2.After you select an alarm, hold down A until the hour setting of the alarm time starts to flash. This indicates the setting screen.
•This operation automatically turns on the alarm.
3.Press C to move the flashing between the hour and minute settings.
4.While a setting is flashing, use D (+) and B
•When setting the alarm time using the
5.Press A to exit the setting screen.
Auto light switch on indicator
The backlight uses an EL
•The auto light switch must be turned on (indicated by the auto light switch on indicator) for it to operate.
•See “Backlight Precautions” for other important information about using the backlight.
To turn on the backlight manually
In any mode, press L to illuminate the display for about one second.
•The above operation turns on the backlight regardless of the current auto light switch setting.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, or until you turn the alarm off or change it to a
Note
•Pressing any button stops the alarm tone operation.
•Performing any one of the following operations during a
Displaying the Timekeeping Mode setting screen Displaying the Alarm 1 setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn Alarms 2 through 5 on and off
1.In the Alarm Mode, use D to select a
2. Press B to toggle the displayed alarm on and off.
• Turning on a
• The
•If any alarm is on, the alarm on indicator is shown on
the display in all modes.
To select the operation of Alarm 1
1.In the Alarm Mode, use D to select Alarm 1.
2.Press B to cycle through the available settings in the sequence shown below.
Snooze alarm on indicator () and one-time alarm on indicator ()
Snooze alarm on | Alarm off |
•The applicable alarm on indicator ( or ) is displayed in all modes when an alarm is turned on.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one second, whenever you position your wrist as described below in any mode. Note that this watch features a “Full Auto EL Light,” so the auto light switch operates only when available light is below a certain level. It does not turn on the backlight under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes the backlight to turn on.
Parallel to | More than |
ground | 40° |
Warning!
•Always make sure you are in a safe place whenever you are reading the display of the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not surprise or distract others around you.
•When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light switch on ( displayed) and off ( not displayed).
•The auto light switch on indicator () is on the display in all modes while the auto light switch is turned on.
3