Operation Guide 2514/2645
Alarm Mode
Hour
5. As with the hour setting, use the D (+) and A
Using the Alarms
❚Alert Types
You can configure an alarm with an hour and minute, as well as a text message (up to eight characters long).
You can configure an alarm to perform either of the two following alert operations.
•Beeper Alert
Signals arrival of an alarm time with a beeper.
•Silent Alert
Signals arrival of an alarm time with a flashing display indicator.
•See “To turn an alarm on and off, and select an alert type” for information about using alerts.
•If you specify message text, the message is displayed for one minute in the Timekeeping Mode when the alarm time is reached.
❚Alarm Types
This watch has five alarms: four daily alarms and one snooze alarm.
❚To set an alarm time
1. In the Alarm Mode, use the D button to scroll through the alarm screens in the sequence shown below until the one you want is displayed.
• The indicator of the currently Alarm 1 Indicator selected alarm is shown on
the display.
Alarm 1 | Alarm 2 | Alarm 3 |
(ALARM1) | (ALARM2) | (ALARM3) |
Hourly Time | Snooze Alarm | Alarm 4 |
Signal (SIGNAL) | (SNOOZE) | (ALARM4) |
• This is the setting screen. |
• If the currently selected alarm |
was turned off, the beeper |
alert turns on at this time, |
indicated by the alarm |
indicator on the display. |
3. Use the D (+) and A |
buttons to change the |
hour setting. |
• Holding down either button |
scrolls characters at high |
speed. |
• When setting the hour, make |
sure you specify AM (no |
indicator) or PM (P) correctly |
when using |
timekeeping, or that you |
specify the correct |
time. |
Alarm Indicator
(Back)
(Forward)
•This causes the first character of the message text to flash, which indicates the input screen.
7.Use the D (+) and A
•Holding down either button scrolls characters at high speed.
First Message
Text Character
(Back)
(Forward)
The alert operation is performed for 10 seconds when the alarm time is reached.
Snooze Alarm (SNOOZE)With the snooze alarm, the alert operation is performed for 10 seconds when the alarm time is reached, and up to seven times at
Alarm 1
Alarm 2
Alarm 3
Alarm 4
Snooze Alarm
4. Press the C button to |
move the flashing to the |
minute digits. |
(Back)
(Forward)
Minute
Supported Characters
• Katakana: ア to ン ァ to ォ ッ ャ to ョ ゛゜
•Lower Case Alpha: a to z
•Symbols: *―_@ . /?#!%.:’,&=÷×-+
•Upper Case Alpha: A to Z
•Numerals: 0 to 9
•Holding down the D or A button while inputting katakana will jump between rows ( ア
8. When the character you want is at the current cursor position, press the C button to move the cursor to the right.
Repeat steps 7 and 8 as many times as necessary to input up to eight characters.
9. When the text is the way you want, press the B button to save it.•This exits the setting screen.
•The display also will exit the setting screen automatically if you do not perform any operation for about two or three minutes.
❚To modify alarm settings
1. In the Alarm Mode, use the D button to display the alarm you want to modify.2. Press the B button so the hour digits flash on the display.•This is the setting screen.
3.Modify the alarm settings.Use the C button to move the cursor to location of the character you want to change, and then use the D and
Abuttons to scroll through characters until the one you want to change to is displayed.
•To clear an alarm, press both the D and A buttons. This causes “CLEAR!” to appear, clears any message text, and sets the alarm time to 12:00 a.m. (midnight).
4. When the alarm is the way you want, press the B button to save it.❚To turn an alarm on and off, and select an alert type
1. In the Alarm Mode, use the D button to scroll through the alarm screens in the sequence shown below until the one you want is displayed.
•In the Alarm Mode, use the D
button to display the alarm you Alarm Indicator want to turn on or off.
2. Use the A button to cycle through the alarm settings in the sequence shown below.
Alert Indicator
No alert operation is performed.
•Beeper Alert OnA beeper sounds for 10 seconds when the alarm time is reached.
•The applicable alarm indicator flashes while the beeper is sounding.
•If there is message text, it appears on the Timekeeping Mode screen for one minute.
•Silent Alert OnThe applicable alarm indicator flashes on the display, without sounding the beeper.
•If there is message text, it appears on the Timekeeping Mode screen for one minute.
❚To test the beeper alert
In the Alarm Mode, hold down the D button to sound the beeper.
Alarm Off | Beeper Alert On | Silent Alert On |
6