Operation Guide 2760 2761
To measure lap times
1. When the stopwatch display shows all zeros, press A to display the lap time screen (indicated by LAP).
2.Press Bto start a time measurement.
3.Press Ato record the time of the first lap.
• This freezes the current lap time on the digital display for about five seconds, while measurement of the next lap time continues internally and elapsed time continues to be indicated by the analog hands.
•After five seconds, the lap number of the displayed
time appears for one second, and then the elapsed time display for the next lap appears.
4. Repeat step 3 to record more lap times.
To delete all stopwatch time records
In the Recall Mode, hold down A and Bfor about two seconds. During that time
–
–
•If you release A and Bbefore –
•The lap number will show LAP – – after all of the stopwatch time records are deleted.
•Note that lap and split times cannot be deleted individually.
•Stopwatch time records can be deleted only when the Stopwatch Mode elapsed time display is cleared to all zeros.
Dual Time
5.Press Bto stop the stopwatch.
6.Press Ato clear the stopwatch to all zeros.
•Lap numbers are automatically incremented starting from 1 whenever you press A in step 3 of the above procedure. The maximum lap number is 99. Recording a lap after that causes the lap number count to restart from 00.
To measure split times
1. When the stopwatch display shows all zeros, press A to display the split time screen (indicated by SPL).
2. Press Bto start a time measurement.
3.Press Ato record the time of the first split.
• This freezes the current split time on the digital
display for about five seconds, while measurement of the next split time continues internally and elapsed time continues to be indicated by the analog hands.
• After five seconds, the elapsed time display for the |
next split appears. |
GMT differential value
Current time in the selected time zone
The Dual Time Mode lets you view the current time in 29 time zones around the world.
•Time zones are indicated on the digital display by their GMT differential values.
•For full information on time zones, see the “Time Zone Table”.
•The watch will perform a signal receive operation even if it is in the Dual Time Mode when a calibration time is reached. If this happens, the Dual Time Mode time settings will be adjusted in accordance with the current time in the Timekeeping Mode’s Home Time Zone.
•All of the operations in this section are performed in the Dual Time Mode, which you enter by pressing C.
4. Repeat step 3 to record more split times. |
5. Press Bto stop the stopwatch. |
6. Press Ato clear the stopwatch to all zeros. |
To time first and second place finishes
1.When the stopwatch display shows all zeros, press Ato display the split time screen (indicated by SPL).
2.Press Bto start a time measurement.
3.Press Awhen the first finisher crosses the finish line.
•This freezes the time of the first finisher on the digital display for about five seconds. After that, the display returns to elapsed time measurement.
4.Press Bwhen the second finisher crosses the finish line, and display the time.
5.Press Ato clear the stopwatch to all zeros.
Memory Management
Any time you start a new elapsed time measurement (from all zeros) in the Stopwatch Mode, the watch automatically deletes all of the stopwatch time records currently in memory.
•The following table shows Stopwatch Mode operations, and how they affect memory storage.
To do this: | Press this button: |
Clear all stopwatch times from memory and | B (when all zeroes are displayed) |
start elapsed time measurement |
|
Pause an elapsed time measurement without | B |
storing data in memory |
|
Restart a paused elapsed time measurement | B |
without storing data in memory |
|
Record a lap or split time in memory during | A |
ongoing elapsed time measurement |
|
Record the currently paused elapsed, lap, or | A (clears display to all zeros) |
To view the time in another time zone
While in the Dual Time Mode, press B to scroll westward through time zones.
•When you release B, the displayed GMT differential value is replaced by the current time in that time zone after about one second.
•Pressing A causes the applicable GMT differential value of the currently selected time zone to appear on the digital display for about one second.
•If the current time shown for a time zone is wrong, check the Timekeeping Mode time setting and your Home Time Zone setting, and make the necessary changes.
To toggle a time zone between Standard Time and Daylight Saving Time
1. In the Dual Time Mode, use B to display the time zone
DST indicator | whose Standard Time/Daylight Saving Time setting you |
| |
| want to change. |
| 2. Hold down A to toggle between Daylight Saving Time |
| (DST indicator displayed) and Standard Time (DST |
| indicator not displayed). |
•The DST indicator appears on the display whenever you display a time zone for which Daylight Saving Time is turned on.
•The DST/Standard Time setting you configure affects only the currently displayed time zone. Other time zones are not affected.
•Note that you cannot use the Dual Time Mode to change the DST setting of the Home Time Zone you currently have selected in the Timekeeping Mode. See “To change the Daylight Saving Time (summer time) setting” for information about turning the Home Time Zone DST setting on and off.
•The G0.0 time (Greenwich Mean Time) zone cannot be switched between Standard Time and Daylight Saving Time.
Alarms
split time in memory |
•The watch has enough memory to hold up to 50 lap/split time records. Recording a lap or split time while there are already 50 records in memory deletes the oldest record to make room for the new one.
•See “Recall Mode” for details on how to recall time records from memory.
Recall Mode
Alarm number
The Alarm Mode gives you a choice of four
Also use the Alarm Mode to turn the Hourly Time Signal on and off.
• There are five alarms numbered AL1, AL2, AL3, AL4 |
(target alarm), and AL5 (snooze alarm). You can |
Lap number
Use the Recall Mode to recall and delete time records stored in the Stopwatch Mode. You can use the Recall Mode to view both lap and split time records.
• All of the operations in this section are performed in the |
Recall Mode, which you enter by pressing C. |
• Entering the Recall Mode displays the number of the |
Alarm time On/Off status (Hour : Minutes)
configure AL5 as a snooze alarm only. Alarms AL1, |
AL2, AL3, and AL4 can be used as |
only. |
• All of the operations in this section are performed in the |
Alarm Mode, which you enter by pressing C. |
Minutes 1/100 second Seconds
last lap recorded in the Stopwatch Mode. After that, the |
applicable lap time appears. If there are no stopwatch |
time records in memory, LAP – – appears on the |
display. |
Hourly Time
Signal Screen
To set an alarm time
1. In the Alarm Mode, use Bto scroll through the alarm | ||
screens until the one whose time you want to set is | ||
displayed. |
|
|
AL 1 | AL 2 | AL 3 |
To recall stopwatch time records
1. In the Recall Mode, press Ato select the either lap time or split time format.
| Press A. |
▲ | ▲ |
Lap Time Format | Split Time Format |
2. Press Bto scroll through the stopwatch time records from the newest to the oldest.
•Each press of B displays the next lap or split number for about one second, and then displays the applicable lap or split time.
•Regardless of whether you are viewing time records using lap time format or split time format, the lap/split number is indicated on the display as LAP 1, LAP 2, etc.
|
|
|
| :00 |
|
| AL 5 |
|
| AL 4 |
| |
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| ||
l |
|
|
| 2. After you select an alarm, hold down A until the hour | ||||||||
|
|
| setting of the alarm time starts to flash, which indicates | |||||||||
l ll |
|
| ||||||||||
l | l |
|
|
|
|
|
|
|
|
|
|
|
l | l |
|
| the setting screen. |
|
|
|
|
|
| ||
l |
|
|
|
|
|
|
|
| ||||
l | l |
|
| • This operation automatically turns on the alarm. | ||||||||
ll | l |
|
| |||||||||
|
|
| ||||||||||
3. Press Cto move the flashing between the hour and minute settings.
4. While a setting is flashing, use D(+) and
• When setting the alarm time using the
5. Press Ato exit the setting screen.
• With the target alarm (AL4), the time starts to countdown as soon as you set the alarm time.
Target Alarm Time | Countdown (Hours, Minutes, Seconds) |
3