Casio 2895 Alarms, Countdown Timer Examples, Alarm Operation, OFF, OFF, :00, OFF, :00, Note, Screen, Setting, Do this:, Do this:, ON or OFF, To do this:, To do this:

One-time alarm on indicator

Operation Guide 2895

Countdown Timer Examples

Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat;

Progress beeper: On

					Reset Period
Start Time		Reset Time		Reset Period Progress Beeper					Countdown
									End Beeper
10'00"		5'00"	4'00"	3'00"		2'00"	1'00"	0'30"	0'00"
	Reset Time Beeper

Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time;

Progress beeper: Off

Start Time	Reset Time						Elapsed time
							measurement
10'00"	5'00"			Countdown		0'00"
				End Beeper
To configure the countdown timer
		1. While the countdown start time is on the display in the
			Countdown Timer Mode, hold down Auntil the
			countdown start time setting starts to flash, which
			indicates the setting screen.
			• If the countdown start time is not displayed, use the
			procedure under “To use the countdown timer” to
			display it.
		2. Press Cto move the flashing in the sequence shown
			below to select other settings.
			Start	Reset	Timer			Progress
			Time	Time	Mode			Beeper

3.When the setting you want to change is flashing, use D and Bto change it as described below.

Setting	Screen	Button Operations
Start Time		Use D (+) and B(–) to change the setting.
		• You can set a start time in the range of 1 to 60 minutes
		in 1-minute increments.
Reset Time		Use D (+) and B(–) to change the setting.
		• You can set a reset time in the range of 1 to 5 minutes
		in 1-minute increments.
Timer Mode		Press D to toggle between the auto-repeat mode (ON)
		and the elapsed time mode (OFF).
		• An auto-repeat indicator ( ) appears when the auto-
		repeat mode is selected.
Progress		Press Dto toggle progress beeper on (ON) and off (OFF).
Beeper		• A progress beeper indicator ( ) appears when this
		setting is turned on.

4. Press A to exit the setting screen.

•The reset time setting must be less than the countdown start time setting.

To use the countdown timer

In the Countdown Timer Mode, press D to start the countdown timer.

•The countdown timer measurement operation continues even if you exit the Countdown Timer Mode.

•The table below describes button operations you can perform to control countdown operations.

To do this:	Do this:
Stop the countdown operation	Press D.
Resume a stopped countdown operation	Press Dagain.
Display the countdown start time	While the countdown is
	stopped, press B.
Stop the countdown operation and display the reset time	Press B.
Start the countdown from the displayed reset time	Press D.

•The table below describes button operations you can perform during an elapsed

time measurement operation in the elapsed time mode.

To do this:	Do this:
Stop the elapsed time operation	Press D.
Resume a stopped elapsed time operation	Press Dagain.
Display the countdown start time	While the elapsed time is
	stopped, press B.
Stop the elapsed time operation and display the reset time	Press B.
Start the countdown from the displayed reset time	Press D.

Alarms

	Alarm number		You can set five independent Daily Alarms. When an
Alarm time			alarm is turned on, the alarm tone sounds when the
(Hour : Minutes)			alarm time is reached. One of the alarms can be
			configured as a snooze alarm or a one-time alarm,
			while the other four are one-time alarms.
			You can also turn on an Hourly Time Signal that causes
			the watch to beep twice every hour on the hour, and a
			brightness alarm that beeps whenever the watch is
			moved from an area where it is dark to an area where it
Mode		Timekeeping	is light.
indicator	Mode time

•There are five alarm screens numbered 1 through 5. The hourly time signal screen is indicated by :00. The brightness alarm screen shows ON or OFF.

•When you enter the Alarm Mode, the screen you were viewing when you last exited the mode appears first.

•All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.

To set an alarm time

1. In the Alarm Mode, use Dto scroll through the alarm screens until the one whose time you want to set is displayed.

x1 x2 x3 x4

ON or OFF :00 x5

•You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2 through 5 can be used as one-time alarms only.

•The snooze alarm repeats every five minutes.

2.After you select an alarm, hold down Auntil the hour setting of the alarm time starts to flash. This indicates the setting screen.

3.Press Cto move the flashing between the hour and minute settings.

4.While a setting is flashing, use D(+) and B(–) to change it.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator).

5.Press Ato exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, or until you turn the alarm off or change it to a one-time alarm.

The watch also has a brightness alarm. When turned on, the brightness alarm causes the watch to beep for 10 seconds when the watch is brought from the dark into the light. The following are the conditions for brightness alarm operation.

•The watch needs to be in the dark for about 30 to 35 minutes for the brightness alarm to become activated.

•The brightness alarm sounds for about 10 seconds, about 15 to 20 minutes after the watch is next exposed to light.

•The brightness alarm sounds only once and then turns off automatically.

Note

•Pressing any button stops the alarm tone operation.

•Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen Displaying the Alarm 1 setting screen

To test the alarm

In the Alarm Mode, hold down Dto sound the alarm.

To turn Alarms 2 through 5 on and off

1. In the Alarm Mode, use D to select a one-time alarm (alarm number 2 through 5).

2. Press B to toggle the displayed alarm on and off.

• Turning on a one-time alarm (2 through 5) displays the one-time alarm on indicator ( ) on its screen.

• The one-time alarm on indicator is displayed in all modes.

• If any alarm is on, the one-time alarm on indicator is shown on the display in all modes.

To select the operation of Alarm 1

1.In the Alarm Mode, use D to select Alarm 1.

2.Press Bto cycle through the available settings in the sequence shown below.

Snooze alarm on indicator ( ) and one-time alarm on indicator ( )

One-time alarm on Snooze alarm on Alarm off

•The applicable alarm on indicator ( or ) is displayed in all modes when an alarm is turned on.

•The snooze alarm on indicator flashes during the 5-minute intervals between alarms.

•Displaying the Alarm 1 setting screen while the snooze alarm is turned on automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).

To turn the hourly time signal and the brightness alarm on and off

Hourly time signal on	1. In the Alarm Mode, use Dto select the Hourly Time
	Signal or the brightness alarm.
indicator
	2. Press Bto toggle the displayed item on and off.
	• Turning on the Hourly Time Signal displays the hourly
	time signal on indicator ( ) on its screen.
	• Turning on the brightness alarm displays the brightness
	RIG
	alarm on indicator (B	HT ) on its screen.

•The hourly time signal on indicator and brightness alarm on indicator are displayed in all modes.

Brightness alarm on indicator

2