Operation Guide 3239/3240
Alarm Types
The alarm type is determined by the settings you make, as described below.
•Daily alarmSet the hour and minutes for the alarm time. This type of setting causes the alarm to sound everyday at the time you set.
•Date alarmSet the month, day, hour and minutes for the alarm time. This type of setting causes the alarm to sound at the specific time, on the specific date you set.
•Set the month, hour and minutes for the alarm time. This type of setting causes the alarm to sound everyday at the time you set, only during the month you set.
•Monthly alarmSet the day, hour and minutes for the alarm time. This type of setting causes the alarm to sound every month at the time you set, on the day you set.
4.While a setting is flashing, press Dto increase it.
•To set an alarm that does not include a month (Daily alarm, Monthly alarm), set x for the month. Press D until the x mark appears (between 12 and 1) while month setting is flashing.
•To set an alarm that does not include a day (Daily alarm,
set xx for the day. Press Duntil the xx mark appears (between the end of the month and 1) while the day setting is flashing.
•When setting the alarm time using the
5.Press A to exit the setting screen.
To select the alarm type
1. In the Alarm Mode, press Dto display the alarm
Alarm on/off indicator | screen. |
|
|
| 2. Press Ato cycle through the available alarm settings | ||
| shown below. |
|
|
| Alarm off | Snooze | |
|
| alarm on | alarm on |
•The alarm on indicator and the snooze alarm on indicator are shown on the display in all modes while these functions are turned on.
•The snooze alarm on indicator flashes during the
•Displaying the Alarm Mode setting screen (page
To test the alarm
In the Alarm Mode, hold down Dto sound the alarm.
To set an alarm time
1. In the Alarm Mode, press Dto display the alarm screen.
2. Hold down Auntil the hour setting of the alarm time starts to flash, which indicates the setting screen.
• This operation automatically turns on the
3. Press Cto move the flashing in the sequence shown below to select other settings.
Hour Minutes Month Day
Alarm Operation
The alarm tone sounds at the preset time for about 10 seconds. In the case of the snooze alarm, the alarm repeats up to seven times every five minutes.
•Pressing any button stops the alarm tone operation.
•The alarm and the Hourly Time Signal sound in all modes.
•Changing the Timekeeping Mode setting screen (page
•If a snooze alarm time is reached while you are setting the current time in the Timekeeping Mode, the alarm sounds only once. Subsequent snooze alarm operations are not performed.
Stopping a Snooze Alarm OperationAfter a snooze alarm time is reached, you can perform the following steps during any
To stop a Snooze Alarm Operation
1.While in the Alarm Mode, press Dto display the alarm screen.
2.Next, press Ato turn off the alarm or to select the
•Note that this also changes the alarm type setting. If you want to use the snooze alarm again, you must
Stopwatch
To turn the Hourly Time Signal on and off
1.In the Alarm Mode, press Dto display the Hourly Time Signal screen.
2.Press A to turn it on and off.
Indicates Hourly Time Signal is on.
Indicates Hourly Time Signal is off.
•The Hourly Time Signal on indicator is shown on the display in all modes while this function is turned on.
Minutes
Hour Seconds
1/100 second
The stopwatch lets you measure elapsed time, split times, and two finishes.
•The display range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds.
•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even if you exit the Stopwatch Mode.
•Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement.
•All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C(page
To measure times with the stopwatch
Elapsed timeStart | Stop | Stop | Clear | |
Split time |
|
|
|
|
Start | Split | Split release | Stop | Clear |
| (SPL displayed) |
|
|
|
Two Finishes |
|
|
|
|
Start | Split | Stop | Split release | Clear |
| First runner | Second runner | Display time of |
|
| finishes. | finishes. | second runner. |
|
| Display time of |
|
|
|
| first runner. |
|
|
|
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone.
•In the Dual Time Mode, the seconds count is synchronized with the seconds count of the Timekeeping Mode.
To set the Dual Time
1. Press Cto enter the Dual Time Mode (page
2. In the Dual Time Mode, hold down A until the hour setting starts to flash, which indicates the setting screen.
3. Press Cto change the selection in the following sequence.
Hour : Minutes Seconds | Hour |
|
|
| Minutes |
|
|
|
4.Press Dto increase the setting.
5.Press Ato exit the setting screen.